Table of Contents
Advertisement
Quick Links
2005 Hutchison Harbour Ring Enterprises Limited
This device complies with Part 15 of the FCC Rules.
All rights in this publication are reserved and no part may
Operation is subject to the following two conditions:
be reproduced without the prior written permission of
(1) this device may not cause harmful interference, and
the publisher. The contents of this publication are
(2) this device must accept any interference received,
believed to be correct at the time of going to press, but
including interference that may cause undesired
any information, specifications, products or services
operation.
mentioned may be modified, supplemented or
Caution: Changes or modifications not expressly
withdrawn without further notice.
approved by the party responsible for compliance could
void the user's authority to operate the equipment.
The Stylized i.Tech logos are trademarks owned by
Hutchison Harbour Ring Enterprises Limited or its
i.Tech declares under our sole responsibility that the
affiliates.
headset is in conformity with the provisions of the
following Council Directives: 1999/5/EC
Bluetooth
®
and the Bluetooth logos are trademarks
owned by Bluetooth SIG, Inc, USA and licensed to i.Tech
Dynamic Limited.
01/2006
i.Tech Clip V
User Guide
S3J-51A05054-03
Advertisement
Table of Contents
Related Manuals for i. Tech Dynamic Clip V
Summary of Contents for i. Tech Dynamic Clip V
- Page 1 Council Directives: 1999/5/EC Bluetooth ® and the Bluetooth logos are trademarks owned by Bluetooth SIG, Inc, USA and licensed to i.Tech Dynamic Limited. 01/2006 S3J-51A05054-03 i.Tech Clip V User Guide...
-
Page 2: Table Of Contents
Table of Contents i.Tech Clip V Overview ... 1 Getting Started ... 2 Charging Your Headset ... 3-5 Charging Time ... 4 Talk and Stand-by Time ... 4 Low Battery ... 5 Turning your Headset On and off ... 5-6 Pairing Your Headset ... -
Page 3: I.tech Clip V Overview
Volume Key Status Indicator Built-in Buzzer Charging Socket Built-in Rechargeable Battery Multi-function Button (MFB) Earphone Getting Started To use your i.Tech Clip V (“the headset”), please follow these simple steps: Charge your headset Pair your headset with a Bluetooth-enabled mobile handset... -
Page 4: Charging Your Headset
Charging Your Headset The Headset comes with a built-in Charger rechargeable battery. Prior to using the headset, it is recommendable to charge the battery fully for the first time. Charging Socket Charger Plug (fig.1) (fig.2) Charging Your Headset Connect the charger to an AC wall outlet (mains socket) and the charger plug to the headset’s charging socket (fig.1). -
Page 5: Turning Your Headset On And Off
Low Battery When the headset is on and the battery becomes low, the status indicator flashes red and the headset emits a beep every 1 minute. Please recharge the battery as described above. If you are setting up the headset and your mobile phone in a noisy environment, we advise you to put on the earphone first so that the beep will be more audible. -
Page 6: Pairing
5. Set the mobile handset to search for Bluetooth devices within 1 meter range as instructed in the mobile handset user guide and select “i.Tech Clip V” from the list. 6. Enter the preprogrammed passkey “0000” and press “OK” to pair your headset and mobile handset. When the... -
Page 7: Using Your Headset
7. Press “Return” to go back to your mobile handset’s main menu. For certain mobile handset models, a headset icon will be shown on the screen. You should now be able to make and receive calls using your headset. IMPORTANT If the pairing cannot be completed within 2 minutes while the pairing mode is activated, the headset status indicator flashes purple followed by 3 beeps and the headset is turned off. -
Page 8: Transferring A Call (Handsfree Profile Only)
Using Your Headset Muting the Microphone You can put a call on hold by muting the microphone. Press and hold the volume key for two seconds until status indicator flashes Red to mute built in Microphone and press and hold the volume key for 3 seconds to deactivate the muting function while conversation. Voice Dialling from Your Headset If your mobile handset is equipped with a voice dialling function, simply press the MFB on your headset, and when you hear a beep say the voice tag. -
Page 9: Adjusting The Volume
Adjusting the Volume Press the Volume Key repeatedly until you reach the desired volume level. The listening volume may be affected by the volume setting of the caller’s phone as well. Re-adjust the listening volume again when necessary. Resetting the Headset You may reset the headset to its original settings at anytime, in doing this you also clear all current pairing settings. -
Page 10: Safety Information
Built-in Battery Do not attempt to replace the headset’s battery yourself as it is built into the headset and is not changeable. • Charge the battery in accordance with the instruction supplied with this user guide. • Only use the manufacturer supplied charger when charging the headset. •... -
Page 11: Troubleshooting
Then start pairing again. Troubleshooting The i.Tech Clip V Headset is compliant with and adopts the Bluetooth Specification 1.2. However, interoperability between the device and other Bluetooth-enabled products is not guaranteed because it depends on compatibility. For more information on the compatibility between the device with other Bluetooth-enabled products, please check with the manufacturer or browse: http://www.itechdynamic.com... -
Page 12: Product Specifications
16.7 grams Declaration of Conformity ( DoC ) We, i.Tech Dynamic Ltd., declare that the following product: Product Name: i.Tech Clip V Model No.: C51-A05054-XX Is in conformity with the following essential requirements of Council Directive 1999/5/EC ( referred to as R&TTE Directive ) : Article 3.1a, 3.1.b and 3.2.
Need help?
Do you have a question about the Clip V and is the answer not in the manual?
Questions and answers