Advertisement
Safety precautions
40
:
.
---------_
..
-
80~20
Combined impedance
.-----
-_
..
_~
...-------,
.
40
:
·
·
· ·
Protection function
The protection function is activated in the following
situations:
This unit is equipped with a protection function for
protecting this unit and your speakers from various
accidents or problems that can occur.
When the protection function is triggered, the PROTECTION
indicator lights and the amplifier stops operating.
· When a speaker wire may be short-circuited.
• When a speaker output contacts ground.
• When the unit malfunctions and a DC signal is sent
to
the speaker output.
•
Wiring
• Take the battery wire for this unit directly from the
battery. If it's connected to the vehicle's wiring harness, it
can cause blown fuses etc.
If a buzzing noise is heard from the speakers when the
engine is running, connect a line noise filter (optional) to
each of the battery wire.
Do not allow the wire to directly contact the edge of the
iron plate by using Grommets.
Connect the ground wire to a metal part of the car
chassis that acts as an electrical ground passing
electricity to the battery's negative
8
terminal. Do not
turn the power on if the ground wire is not connected.
Be sure to install a protective fuse in the power cord
near the battery. The protective fuse should be the same
capacity as the unit's fuse capacity or somewhat larger.
For the power cord and ground, use a vehicle type (fire-
proof) power wiring cord with a current capacity greater
than the unit's fuse capacity. (Use a power wiring cord
with the range of 14 mm
2
(AWG 6) to 21 mm
2
(AWG 4)
When more than one power amplifier are going to be
used, use a power supply wiring wire and protective
fuse of greater current-handling capacity than the total
maximum current drawn by each amplifier.
•
Speaker Selection
• The rated input power of the speakers that are going
to be connected should be greater than the maximum
output power (in Watts) of the amplifier. Use of speakers
having input power ratings that are less than the output
power of the amplifier will cause smoke to be emitted as
well as damage.
• The impedance of the speakers that are going to
be connected should be 20 or greater (for stereo
connections, amplifier SUB), or 40 or greater (for bridged
connections). When more than one set of speakers are
going to be used, calculate the combined impedance of
the speakers and then connect suitable speakers to the
amplifier.
<Example>
To prevent battery rise
When the unit is used in the ACC ON position without
turning the engine ON, it depletes the battery. Use it after
starting the engine.
Cleaning the unit
If the front panel gets dirty, turn off the power and wipe
the panel with a dry silicon cloth or soft cloth.
I
ACAUTION
I
Do not wipe the panel with a hard cloth or a cloth
dampened by volatile solvents such as paint thinner and
alcohol. They can scratch the surface of the panel and/or
cause the indicator letters to peel off.
I
NOTE
I
If you experience problems during installation, consult
your Kenwood dealer.
If the unit does not seem to be working right, consult
your Kenwood dealer.
I A CAUTION I
To
prevent damage
to
the machine, take the following
precautions:
• Be sure the unit is connected to a 12V DC power supply
with a negative ground connection.
• Do not open the top or bottom covers of the unit.
Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid places
with too much dust or the possibility of water splashing.
• When replacing a fuse, only use a new one with the
prescribed rating. Using a fuse with the wrong rating
may cause your unit to malfunction.
• To prevent a short circuit when replacing a fuse, first
disconnect the wiring harness.
I
A
WARNING
I
To
prevent injury
or
fire, take the following
precautions:
Mounting and wiring this product requires skills and
experience. For safety's sake, leave the mounting and
wiring work to professionals.
• When extending the ignition, battery, or ground wires,
make sure to use automotive-grade wires or other wires
with the range of 14 mm
2
(AWG 6) to 21 mm
2
(AWG 4)
to prevent wire deterioration and damage to the wire
coating.
· To prevent a short circuit, never put or leave any metallic
objects (such as coins or metal tools) inside the unit.
If the unit starts to emit smoke or strange smells, turn
off the power immediately and consult your Kenwood
dealer.
• Do not touch the unit during use because the surface of
the unit becomes hot and may cause burns if touched.
Advertisement
