Husqvarna 333R Operator's Manual
Husqvarna grass trimmer operator's manual
Hide thumbs
Also See for 333R:
- Workshop manual (62 pages) ,
- Operator's manual (44 pages) ,
- Operator's manual (40 pages)
Related Manuals for Husqvarna 333R
Summary of Contents for Husqvarna 333R
- Page 1 Oper ator’s manual (EPA) 333R 335R X-series Please r ead the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
-
Page 2: Key To Symbols
Arrows which show limits for handle positioning. Always wear approved protective gloves. Wear sturdy, non-slip boots. Only use non-metallic, flexible cutting attachments, i.e. trimmer heads with trimmer cord. 2 – English KEY T O SYMBOLS Star ting instructions Other symbols/decals on the mac hine refer to special certification requirements for certain markets. -
Page 3: Table Of Contents
Fitting the guard extension ... Fitting a blade guard, grass blade and grass cutter ... Fitting the blade guard and saw blade ... Fitting a trimmer guard and Superauto II 1" trimmer head ... Fitting other guards and cutting attachments ... -
Page 4: Intr Oduction
Dear customer! Cong ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant. -
Page 5: Wha T Is What
What is what on the c learing saw? 1 Trimmer head 2 Grease filler cap, bevel gear 3 Bevel gear 4 Cutting attachment guard 5 Shaft 6 Handlebar 7 Throttle control 8 Stop switch 9 Throttle lock 10 Suspension 11 Cylinder cover... -
Page 6: General Safety Preca Utions
Personal protective equipment IMPOR TANT! A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of this operator’s manual. -
Page 7: Machine ' S Safety Equipment
GENERAL SAFETY PRECA UTIONS Mac hine ′ ′ ′ ′ s safety equipment This section descr ibes the machine ′ s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is what?”... -
Page 8: Vibration Damping System
GENERAL SAFETY PRECA UTIONS Vibration damping system Your machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier. Using incorrectly wound cord or a blunt or incorrect cutting attachment (wrong type or incorrectly filed, see instructions under the heading Filing the blade) increases the level of vibration. -
Page 9: Locking Nut
GENERAL SAFETY PRECAUTIONS Regularly check that the muffler is securely attached to the machine. If the muffler on your machine is fitted with a spark arrestor mesh this must be cleaned regularly. A blocked mesh will cause the engine to overheat and may lead to serious damage. - Page 10 Saw blades are intended for cutting fibrous types of wood. Grass blades and grass cutters are intended for cutting coarse grass. A trimmer head is intended for trimming grass. General rules Only use cutting attachments with the guards we recommend! See the chapter on Technical data.
-
Page 11: Trimmer Head
• Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the correct length. • To increase the life of the cord it can be soaked in water for a couple of days. -
Page 12: Assembly
Fitting the guard extension CAUTION! The guard extension shall always be fitted when using the trimmer head/plastic blades and combination guard. The guard extension shall always be removed when using the grass blade and combination guard. -
Page 13: Fitting A Blade Guard, Grass Blade And Grass Cutter
Fitting a blade guard, grass blade and grass cutter • Hook the blade guard/combination guard (A) onto the fitting on the shaft and secure with the bolt. CAUTION! Ensure that the guard extension is removed. Use the recommended blade guard. See the Technical data section. -
Page 14: Fitting A Trimmer Guard And Superauto Ii 1" Trimmer Head
(Caution! left-hand thread). • Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover. -
Page 15: Adjusting The Harness And Clearing Saw
Adjusting the harness and clearing WARNING! When using a clearing saw it must always be hooked securely to the harness. Otherwise you will be unable to control the clearing saw safely and this can result in injury to yourself or others. Never use a harness with a defective quick release. -
Page 16: Fuel Handling
When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For best results and performance use HUSQVARNA two- stroke engine oil, which is specially formulated for our air- cooled two stroke-engines. • Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW). -
Page 17: Fueling
Mixing • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. •... -
Page 18: Starting And Stopping
• Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked. • Never use the machine without a guard nor with a defective guard. -
Page 19: For Throttle Handles With A Start Throttle Lock
STARTING AND STOPPING Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!). Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (the starter pawls grip), now quickly and powerfully pull the cord. -
Page 20: Working Techniques
General working instructions IMPORTANT! This section describes the basic safety precautions for working with clearing saws and trimmers. If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop. Avoid all usage which you consider to be beyond your capability. -
Page 21: Forestry Clearing Using A Saw Blade
WARNING! Sometimes branches or grass get caught between the guard and cutting attachment. Always stop the engine before cleaning. Working methods WARNING! Avoid cutting with the area of the blade between the 12 o’clock and 3 o’clock positions. Because of the speed of rotation of the blade kickback can occur if you attempt to cut thick stems with this area of the blade. -
Page 22: Brush Cutting With A Saw Blade
Grass trimming with a trimmer head Trimming • Hold the trimmer head just above the ground at an angle. It is the end of the cord that does the work. Let the cord work at its own pace. Never press the cord into the area to be cut. - Page 23 Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. CAUTION! This technique increases the wear on the cord.
-
Page 24: Carburetor
Carburetor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions... -
Page 25: High Speed Jet H
H. You should therefore fit the trimmer head T35 (2.7 mm cord) before adjusting the high speed jet. The cord length should be standard, i.e. to the knife on the trimmer guard. Apply full throttle and turn the high speed jet H very slowly clockwise until the engine slows down. -
Page 26: Cooling System
See instructions under the heading Oiling the air filter. Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact. -
Page 27: Spark Plug
• Adjust the blade setting. This should be 1 mm. Note: Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically... -
Page 28: Maintenance Schedule
Check that the trimmer head is undamaged and not cracked. Replace the trimmer head if necessary. Check that the locking nut of the cutting equipment is tighten correctly. -
Page 29: Technical Data
1/2 idle and 1/2 max. speed. NOTE! Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting equipment fitted. The table indicates the highest and lowest values. TECHNICAL DATA 333R 2,11/34,6 1,50/38,0 1,20/30,5... -
Page 30: Technical Data
Approved accessories Centre hole in blades/cutters, Ø 25,4 mm Output shaft thread M12 Grass blade/grass cutter Saw blade Plastic blades Trimmer head Support cup 30 – English TECHNICAL DATA Type Multi 255-3 (Ø 255 3 teeth) Grass 255-4 (Ø 255 4 teeth) Multi 275-4 (Ø... -
Page 31: Federal Emission Control Warranty Statement
The warranty period begins on the date small nonroad engine is delivered. LENGTH OF COVERAGE Husqvarna Forest & Garden warrants to the initial owner and each subsequent purchaser that the engine is free from defects in materials and workmanship which cause the failure of a warranted part for a period of two years. - Page 32 Super Auto II Super Auto II 1 " 4,0 m 15 cm ~2,0 m 6 " 6,5 ' 15 cm 6 "...
- Page 34 8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...
- Page 35 4,25 m 4,25 m 15 cm 6" 15 cm 6"...
- Page 36 15 cm 6" 8,5 m 10 cm 4" 4,3 m "Clic"...
- Page 38 ´®z+HAe¶5f¨ ´®z+HAe¶5f¨...
- Page 40 1140336-95 ´®z+HAe¶5f¨ ´®z+HAe¶5f¨ 2005-09-14...
Need help?
Do you have a question about the 333R and is the answer not in the manual?
Questions and answers