Pioneer Premier PRS-D1200SPL Owner's Manual
  1. Manuals
  2. Brands
  3. Pioneer Manuals
  4. Car Amplifier
  5. PRS-D1200SPL - Premier Amplifier
  6. Owner's manual
Pioneer Premier PRS-D1200SPL Owner's Manual

Pioneer Premier PRS-D1200SPL Owner's Manual

Class d mono amplifier
Hide thumbs Also See for Premier PRS-D1200SPL:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual, Owner's Manual
CLASS D MONO AMPLIFIER
AMPLIFICATEUR MONO DE CLASSE D
Owner's Manual
PRS-D1200SPL
Mode d'emploi

Advertisement

Table of Contents
loading

Related Manuals for Pioneer Premier PRS-D1200SPL

Summary of Contents for Pioneer Premier PRS-D1200SPL

  • Page 1 CLASS D MONO AMPLIFIER AMPLIFICATEUR MONO DE CLASSE D Owner’s Manual PRS-D1200SPL Mode d’emploi...

  • Page 2: Table Of Contents

    Contents Before Using This Product Before Using This Product ...... 1 Thank you for purchasing this PIONEER product. It is designed to give you many Information to User .......... 1 years of enjoyment. Important ............1 PIONEER SUGGESTS USING A PRO- Product Registration ..........

  • Page 3: Product Registration

    Product Registration WARNING Visit us at the following site: • Handling the cord on this product or cords associ- ated with accessories sold with the product may expose you to chemicals listed on proposition 65 known to the State of California and other gov- ernmental entities to cause cancer and birth defects or other reproductive harm.

  • Page 4: Setting The Unit

    Setting the Unit Terminal Cover MODE SELECT Switch Before setting up the unit, unfas- You can select amplifier’s sync mode from ten the screws with a 4 mm MASTER, SYNC and SYNC INV. Set the hexagonal wrench and remove MODE SELECT switch to the MASTER posi- the terminal cover.

  • Page 5: Gain Control

    • When using with an RCA equipped car stereo (standard output of 500 mV), set to the NORMAL position. When using with an RCA equipped Pioneer car stereo with max. output of 4 V or more, adjust level to match the car stereo output level.

  • Page 6: Setting The Gain Properly

    • If you decrease the volume of the head unit and set the gain control of the amplifier to the proper position but still the sound cuts out from time to time, contact the nearest authorized PIONEER Service Station.

  • Page 7: Connecting The Unit

    Connecting the Unit CAUTION • Disconnect the negative (–) terminal of the bat- • Make sure that wires will not interfere with mov- tery to avoid the risk of short-circuit and damage ing parts of the vehicle, such as the gearshift, to the unit.

  • Page 8: Connection Diagram

    Connecting the Unit Connection Diagram • In the case of connecting the external output from a car stereo to an RCA input, use the jack used for full- range output. This is because the LPF of the amplifier cannot be turned OFF. If this jack cannot be used, connect the subwoofer output jack to the RCA input.

  • Page 9: Solderless Terminal Connections

    Solderless Terminal Connections 1. Expose the end of the speaker wires using nippers or a cutter by about 18 • Since the wire will become loose over time, it mm to 20 mm (3/4 in.). must be periodically inspected and tightened as necessary.

  • Page 10: Connecting The Power Terminal

    Connecting the Unit Connecting the Power Terminal 2. Expose the end of wires using nip- pers or a cutter. • Always use the recommended battery and ground • Battery wire, ground wire: wire, which is sold separately. Connect the bat- 18 mm to 20 mm (3/4 in.) tery wire directly to the car battery positive termi- •...

  • Page 11: Setting The Gain For Synced Amplifier

    Setting the Gain for synced amplifier After connecting the speaker wires, adjust each synced amplifier’s gain control. All synced amplifiers follow the master amplifier’s settings. Quick Setup of the Gain Set each synced amplifier’s gain control to the NORMAL position. This setting will balance output volumes sufficiently for most applications.
  • Page 12 Connecting the Unit CAUTION Amplifier Amplifier Diagram A - Proper Diagram B - Improper 4 Ω 4 Ω 2 Ω 2 Ω Speaker Speaker Speaker Speaker 1 Ω Bridged Mode 2 Ω Bridged Mode Amplifier Amplifier DO NOT install or use this amplifier by wiring speakers rated at 2 Ω (or lower) in parallel to achieve a 1 Ω (or lower) bridged mode (Diagram B).
  • Page 13 Two Amplifier (Ex. Bridge) Connect to a car stereo. MODE SELECT switch SYNC OUTPUT For details, see the “Connection Diagram”. must be in MASTER position. Connecting wire with RCA pin plugs (sold 2 Ω to separately). MODE SELECT switch 16 Ω must be in SYNC INV 2 400 W position.
  • Page 14 Connecting the Unit Four Amplifier (Ex. Bridge) Connect to a car stereo. For details, see the MODE SELECT switch SYNC “Connection Diagram”. must be in MASTER OUTPUT position. MODE SELECT Connecting wire with switch must be in RCA pin plugs (sold separately).
  • Page 15 Four Amplifier Connect to a car stereo. For details, see the MODE SELECT switch “Connection Diagram”. SYNC OUTPUT must be in MASTER position. MODE SELECT Connecting wire with 1 Ω to 8 Ω switch must be in RCA pin plugs (sold 1 200 W separately).

  • Page 16: Installation

    Installation CAUTION CAUTION • Do not install in: To prevent malfunction and/or injury —Places where it could injure the driver or pas- • To ensure proper heat dissipation of the amplifier, sengers if the vehicle stops suddenly. be sure of the following during installation. —Places where it may interfere with the driver, —Allow adequate space above the amplifier for such as on the floor in front of the driver’s...

  • Page 17: Example Of Installation On The Floor Mat Or On The Chassis

    Example of installation on the floor Replacing the terminal cover mat or on the chassis 1. Align the unit and terminal cover, and insert the screw. 1. Place the amplifier where it is to be installed. Insert the supplied tap- 2.

  • Page 18: Additional Information

    Additional information Troubleshooting The following indicators light momentarily when the amplifier is turned on. This is not a malfunction. HEAT Indicator • This indicator lights up in yellow when the temperature within the amplifier rises. When this happens, immediately discontinue use of the amplifier and check the location where the amplifier is installed (see the “WARNING”...

  • Page 19: Specifications

    Specifications Power source ......................14.4 V DC (10.8 V to 15.1 V allowable) Grounding system ............................Negative type Current consumption ......................44 A (at continuous power, 4 Ω) Average current drawn* ......................12 A (4 Ω for one channel) 26 A (2 Ω for one channel) 34 A (1 Ω...
  • Page 20 300 Allstate Parkway, Markham, Ontario L3R OP2, Canada Copyright © 2007 by Pioneer Corporation. TEL: 1-877-283-5901 All rights reserved. PIONEER ELECTRONICS DE MEXICO, S.A. de C.V. Publication de Pioneer Corporation. Blvd.Manuel Avila Camacho 138 10 piso Copyright © 2007 Pioneer Corporation.

Table of Contents