Identification Of Controls - NAD D 1050 Owner's Manual

1
DIGITAL AUDIO INPUT
COAXIAL 1 COAXIAL 2
1 DIGITAL AUDIO INPUT (COAXIAL 1, COAXIAL 2, OPTICAL 1,
OPTICAL 2)
•
Connect to the corresponding optical or coaxial digital output of
sources such as CD or BD/DVD players, digital cable box, digital
tuners and other applicable components.
2 USB
• Asynchronous USB 24 bit/192 kHz input assures lowest jitter for best
musical performance.
• Using Type A to Type B cable connector (not supplied), interface
computer audio to this asynchronous Type B USB input to directly
stream 24/192 PCM content from your PC or MAC.
• Ensure that the Sound or Audio device setting of your computer is
set to "NAD USB Audio".
MINIMUM PC SYSTEM REQUIREMENT
Microsoft Windows XP Service Pack 2 or higher, Microsoft Windows 7
FOR MAC USERS
Minimum Mac OS X Snow Leopard (version 10.6) and later versions
NOTE
Download and install to your PC the NAD USB Audio driver from the
Manuals/Downloads tab of the NAD web address http://nadelectronics.
com/products/digital-music/D-1050-USB-DAC.
3 5V DC IN
• Connect corresponding end of the Switch Mode Power Supply
(SMPS) to the 5V DC IN of D 1050 and then connect the SMPS plug
to a mains power source.
• Before connecting the SMPS plug to the mains power source,
ensure first that the other end of the SMPS connected to the 5V DC
IN socket is firmly connected.
•
Always disconnect the SMPS plug from the mains power source
first, before disconnecting from the 5V DC IN socket the other end
of the SMPS.
2
USB
1 OPTICAL 2 SERVICE
BALANCED
UNBALANCED
R L
R L
2 CHANNEL AUDIO OUT
4

IDENTIFICATION OF CONTROLS

3
-
+
5V DC IN
© NAD D1050
4 2 CHANNEL AUDIO OUT (BALANCED, UNBALANCED)
• Connect to corresponding balanced and/or unbalanced audio input
of compatible devices such as receivers, amplifiers, audio processors
or music system.
•
Audio output from 2 CHANNEL AUDIO OUT (BALANCED and
UNBALANCED) is fixed.
•
Adjust audio level via the volume control of the device that D 1050
is hooked up.
5 (STANDBY)
• With the corresponding end of the SMPS connected to the 5V DC
IN socket of the D 1050 and the SMPS plug connected to a mains
power source, press (Standby) to switch ON the D 1050 from
standby mode. The Standby indicator will turn from amber to
bright/white color. Pressing
to standby mode.
6 S (SOURCE)
• Toggle to cycle through the Sources (COAXIAL 1, COAXIAL 2,
OPTICAL 1, OPTICAL 2 and USB) and select desired Source.
7 VOLUME (applicable for headphone listening only)
•
Adjust headphone audio level by turning clockwise or
counterclockwise. This volume control does not affect the 2
CHANNEL AUDIO OUT level.
8 DISPLAY
• Illuminate the selected or active Source (COAX 1, COAX 2, OPT 1,
OPT 2 or USB) and corresponding sample rate of selected audio
source (32, 44.1, 48, 96 or 192).
9 PHONES
• A 3.5 mm stereo jack socket is supplied for headphone listening.
•
Specially designed low noise headphone circuitry can
accommodate a wide range of phones, even 600 Ohm studio
models.
• Ensure that the volume control is turned to minimum (fully
counterclockwise) before connecting or disconnecting
headphones. Listening at high levels can damage your hearing.
• When a headphone is connected to PHONES, 2 CHANNEL AUDIO
OUT is muted.
5
6
7
8
9
(Standby) again turns the unit back
5