Omron R1 Instruction Manual

2. Preparation
2.1 Installing/Replacing the Batteries
1.
Remove the battery compartment cover
by pulling it off in the direction of the
Wrist Blood
arrow.
Pressure Monitor
1) Push the hook on the bottom of the
battery cover.
R1
Model
2) Pull the cover off the main unit.
Instruction Manual
IM-HEM-6114-RU-04-07/2011
2.
Insert two identical 1.5V "AAA"
5329529-5B
alkaline (LR03) batteries in the
Introduction
battery compartment.
Thank you for purchasing the OMRON R1 Wrist Blood Pressure Monitor.
Make sure their polarity (+/-) is
This remarkable, compact and easy to use instrument is ideal for people who aligned with the polarity (+/-) as
frequently monitor their own blood pressure. The small, pre-formed wrist cuff is
indicated in the battery compartment.
very convenient and easy to apply.
3.
Put the battery cover back in place.
The OMRON R1 is a compact and easy to use blood pressure monitor,
operating on the oscillometric principle. It measures your blood pressure and Note: The measurement values continue to be stored in memory even
after the batteries are replaced.
pulse rate simply and quickly. For comfortable controlled inflation without the
need of pressure pre-setting or re-inflation the devices uses its advanced
"IntelliSense" technology.
2.2 Battery Life & Replacement
The unit also stores the last measurement value in memory.
If the battery low symbol (
Intended Use
replace both batteries at the same time.
This product is designed to measure the blood pressure and pulse rate of
people within the range of the designated wrist cuff, following the instructions in
this instruction manual.
- When the battery low symbol (
It is mainly designed for general household use. Please read the Important
the unit for a short while. You should replace the batteries with new ones
Safety Information in this instruction manual before using the unit.
as soon as possible.
- When the symbol (
Please read this instruction manual thoroughly before using the unit. For
replace the batteries with new ones at once.
specific information about your own blood pressure, CONSULT YOUR
DOCTOR. • Turn the unit off before replacing the batteries.
• Remove the batteries if the unit will not be used for three months or more.
• Dispose of batteries according to applicable local regulations.
Important Safety Information
• Two new identical 1.5V "AAA" alkaline batteries will last for approximately
300 measurements, when used to take two measurements a day.
Consult your doctor prior to using in pregnancy or if diagnosed with arrhythmia
• Since the supplied batteries are for monitoring use only, they may have a
or arteriosclerosis.
shorter life and do not last for 300 measurements.
Please read this section carefully before using the unit.
Warning:
• Indicates a potentially hazardous situation which, if not avoided, could result
3. Using the Unit
in death or serious injury.
(General Usage)
3.1 Applying the Wrist Cuff
• Always consult your doctor. Self-diagnosis of measurement results and
You can take a measurement on either your left or right wrist.
self-treatment are dangerous.
• People with severe blood flow problems, or blood disorders, should consult a Notes:
doctor before using the unit, as cuff inflation can cause internal bleeding. • You can take a measurement on either your left or right arm.
The blood pressure can differ between the right arm and the left arm
(Battery Usage)
and therefore also the measured blood pressure values can be
• If battery fluid should get in your eyes, immediately rinse with plenty of clean
different. Omron recommends to always use the same arm for
water. Consult a doctor immediately.
measurement. If the values between the two arms differ
Caution:
substantially, please check with your physician which arm to use for
• Indicates a potentially hazardous situation which, if not avoided, may result in minor or
your measurement.
moderate injury to the user or patient or damage to the equipment or other property.
• To ensure correct measurement, apply the wrist cuff so that it fits
(General Usage)
comfortably around your wrist.
• Do not leave the unit unattended with infants or persons who cannot express their consent.
• Do not apply over clothing.
• Do not use the unit for any purpose other than measuring blood pressure.
• Do not disassemble the unit or wrist cuff. 1. Place the wrist cuff over your left wrist with your left thumb
• Do not inflate the wrist cuff over 299 mmHg.
facing upward.
• Do not use a mobile phone or other devices that emit electromagnetic fields,
near the unit. This may result in incorrect operation of the unit.
• Do not operate unit in a moving vehicle (car, airplane).
(Battery Usage)
• If battery fluid should get on your skin or clothing, immediately rinse with
plenty of clean water.
• Use only two "AAA" alkaline batteries with this unit. Do not use other types of batteries.
• Do not insert the batteries with their polarities incorrectly aligned.
• Replace old batteries with new ones immediately. Replace both batteries at
the same time.
• Remove the batteries if the unit will not be used for three months or more.
Note: Make sure that the wrist cuff does not cover the protruding part of
• Do not use new and used batteries together.
the wrist bone (ulna) on the outside of the wrist.
General Precautions
• Do not apply strong shocks and vibrations to or drop the unit.
2.
Hold the bottom part of the wrist
• Do not take measurements after bathing, drinking alcohol, smoking,
cuff and wrap it around the wrist
exercising or eating.
• Do not inflate the wrist cuff when it is not wrapped around your wrist. while pulling so that it fits
• Do not wash the wrist cuff or immerse it in water.
comfortably.
• Read and follow the "Important information regarding Electro Magnetic
Compatibility (EMC)" in the Technical Data Section.
Notes:
• Read and follow the "Correct Disposal of This Product" in the Technical Data
• Unless the wrist cuff is wrapped securely
Section when disposing of the device and any used accessories or optional parts.
around the wrist, it will not be possible to take
correct measurements.
• If you have a slender wrist, the cuff may feel
1. Overview
slightly loose.
However, this will not affect measurement
Main unit:
results and you should not force the cuff to fit.
C
A
• The remaining part of the wrist cuff can be
conveniently folded back out of the way.
D
B
• If the remaining part of the cuff is difficult to
fold back, measurement results will not be
A. Display C. Wrist cuff
effected.
B. Battery compartment cover D. O/I START button
Display:
E
Taking a reading on the right wrist
F
Measurements can also be made on
I
G
J the right wrist.
K
Fit the unit on the right wrist as shown.
H
E. Systolic blood pressure I. Heartbeat symbol
F. Diastolic blood pressure (Flashes during measurement)
G. Memory symbol
J. Pulse
(Displayed when viewing K. Deflation symbol
last value stored in memory)
H. Battery low symbol
3.2 Correct Posture
Correct posture during measurement helps you get accurate results.
You should also try to measure your blood pressure at the same time each day.
Notes:
• Do not take measurement after bathing, drinking alcohol, or exercising.
2
• Do not move or talk during measurement.
Sit comfortably with your
1 back straight, hold your arm
across your chest and relax.
Relax your wrist and hand.
) appears on the display,
) starts to blink, you will still be able to use
) remains lit, the batteries are exhausted. You should
Do not bend Do not clench
your wrist back. your fist.
3.3 Taking a Reading
1.
Press the O/I START button to start measurement.
The wrist cuff will start to inflate automatically after the
power is turned on.
2. After the unit has detected your blood pressure and
pulse rate, the cuff automatically deflates and your blood
pressure and pulse rate are displayed.
Notes:
• Sit still and do not talk or move until the measurement is completed.
• Keep the unit at heart height until the measurement is completed.
• To stop measurement, press the O/I START button at any time during
measurement.
3.
Check the measurement result.
The unit automatically stores blood
pressure and pulse rate into its
memory.
Refer to "3.4 Using the Memory
ulna
Function".
4.
Undo the cuff and remove the unit.
5.
Press the O/I START button to turn off the unit.
If you forget to turn off the unit, it will shut itself off
automatically after two minutes.
3.4 Using the Memory Function
This unit automatically stores the last measurement value.
To View Previous Readings Stored in Memory
1.
Press and hold the O/I START button until the last
measurement value is displayed along with the memory
symbol.
2.
Press the O/I START button to turn
the unit off.
Note: If you forget to turn the unit off, it will
automatically shut itself off after two
minutes.
To Delete the Value Stored in Memory
To delete stored reading, first press and hold the O/I
START button until the measurement value is displayed.
Then keep the button pressed down for about 10 seconds.
The last reading will then be deleted.
Note: After the reading has been deleted, the screen to the right of the
illustration above appears. Release the buttons to return to the
memory display.
4. Handling Errors and Problems
4.1 Error Messages
Error Symbol Cause Correction
Repeat measurement.
Cuff over inflated.
Remain still and do not move
during measurement.
Position your arm so that
the unit is at the same (Refer to "3.3 Taking a
Reading".)
level as your heart.
Movement during
measurement.
The wrist cuff Carefully read and repeat
is not fastened the steps listed under
securely. "3.1 Applying the Wrist Cuff".
An Er mark with
a code/number
Consult your OMRON retail
indicates the
outlet or distributor.
device has a
hardware failure.
Do not use your other
hand to support the wrist cuff.
This can result in inaccurate
measurement results.
Replace the batteries with two
The battery
new "AAA" alkaline (LR03)
power is low.
batteries.
Blinks or appears
continuously
4.2 Troubleshooting
Do not bend
Symptom Cause Correction
your wrist forward.
Measure while in
Are you holding
the correct posture.
the wrist cuff at
(Refer to "3.2 Correct
heart level?
Posture".)
Is the cuff Wrap the cuff correctly.
wrapped snugly (Refer to "3.1 Applying
The reading is
around the wrist? the Wrist Cuff".)
extremely low (or
Relax and try taking
high).
Are your arms and the measurement again.
shoulders tense? (Refer to "3.3 Taking
a Reading".)
Remain still and do not
Movement or
talk during measurement.
talking during
(Refer to "3.3 Taking
measurement.
a Reading".)
Wrist cuff pressure Air is leaking from Consult your OMRON
retail outlet or distributor.
does not rise. the wrist cuff.
Apply the cuff correctly
so that it is securely
Wrist cuff deflates
The wrist cuff is loose. wrapped around the wrist.
too soon.
(Refer to "3.1 Applying
the Wrist Cuff".)
Blood pressure readings
constantly vary with time
of day and how relaxed
The blood pressure is different each time.
you are. Take several
The reading is extremely low (or high).
deep breaths and try to
remain relaxed before
taking a measurement.
The unit loses power The batteries are Replace the batteries
during measurement. drained. with new ones.
The batteries are Replace the batteries
Nothing happens drained. with new ones.
when you press
The batteries have Insert the batteries
the buttons.
been inserted with the correct (+/-)
incorrectly. polarity.
• Press the O/I START button and repeat
measurement.
• If the problem continues, try replacing the
Other problems.
batteries with new ones.
If this still does not solve the problem, contact
your OMRON retail outlet or distributor.
Systolic blood pressure
Diastolic blood pressure
Pulse
5. Maintenance and Storage
Important information regarding Electro Magnetic Compatibility (EMC)
To protect your unit from damage, please avoid the following: With the increased number of electronic devices such as PC's and mobile
(cellular) telephones, medical devices in use may be susceptible to
• Subjecting your unit to extreme temperatures, humidity,
electromagnetic interference from other devices. Electromagnetic
or direct sunlight. interference may result in incorrect operation of the medical device and
create a potentially unsafe situation.
• Washing the cuff or exposing the cuff or unit to water.
Medical devices should also not interfere with other devices.
• Disassembling the unit.
In order to regulate the requirements for EMC (Electro Magnetic
• Subjecting the unit to strong shocks or vibrations.
Compatibility) with the aim to prevent unsafe product situations, the
Dropping the unit.
EN60601-1-2:2007 standard has been implemented. This standard defines
• Cleaning the unit with volatile liquids.
the levels of immunity to electromagnetic interferences as well as maximum
levels of electromagnetic emissions for medical devices.
This medical device manufactured by OMRON HEALTHCARE conforms to
this EN60601-1-2:2007 standard for both immunity and emissions.
Nevertheless, special precautions need to be observed:
• Do not use mobile (cellular) telephones and other devices, which generate
strong electrical or electromagnetic fields, near the medical device. This
may result in incorrect operation of the unit and create a potentially unsafe
situation. Recommendation is to keep a minimum distance of 7 m. Verify
correct operation of the device in case the distance is shorter.
Further documentation in accordance with EN60601-1-2:2007 is available at
OMRON HEALTHCARE EUROPE at the address mentioned in this instruction
manual.
Documentation is also available at www.omron-healthcare.com.
• The unit should be cleaned with a soft, dry cloth.
Correct Disposal of This Product
• Use a soft, moistened cloth and soap to clean the cuff.
(Waste Electrical & Electronic Equipment)
• Keep the unit in its storage case when not in use.
This marking shown on the product or its literature, indicates
• Fold the cuff into the storage case.
that it should not be disposed of, with other household wastes
Do not store the unit in the following situations: at the end of its working life. To prevent possible harm to the
environment or human health from uncontrolled waste
• If the unit is wet.
disposal, please separate this from other types of wastes and
• Locations exposed to extreme temperatures, humidity,
recycle it responsibly to promote the sustainable reuse of
direct sunlight, dust or corrosive vapours.
material resources.
• Locations exposed to vibrations, shocks or where it will
Household users should contact either the retailer where they purchased
be at risk of falling.
this product, or their local government office, for details of where and how
they can take this item for environmentally safe recycling.
Calibration and Service
Business users should contact their supplier and check the terms and
• The accuracy of this blood pressure monitor has been
conditions of the purchase contract. This product should not be mixed with
carefully tested and is designed for a long service life. other commercial wastes for disposal.
• It is generally recommended to have the unit inspected
This product does not contain any hazardous substances.
every two years to ensure correct functioning and
accuracy. Please consult your authorised OMRON
Manufacturer
dealer or the OMRON Customer Service at the address
given on the packaging or attached literature.
• If the wrist cuff needs to be replaced have this done by
an authorised expert. Consult your authorised OMRON
EU-representative
dealer or the OMRON Customer Service.
• Do not carry out any repairs by yourself. If a defect
occurs or you have doubts about the correct functioning
of the device, consult your authorised OMRON dealer
Exclusive
or the OMRON Customer Service.
distributor in
Russia & importer
6. Technical Data
Production Facility
Product Description Wrist Blood Pressure Monitor
Model OMRON R1 (HEM-6114-RU)
Display LCD Digital Display
Measurement Oscillometric method
Measurement Range Pressure: 0 mmHg to 299 mmHg
Pulse: 40 to 180 beats/min
Memory Last measurement
Accuracy Pressure: within ±3 mmHg
Pulse rate: within ±5% of reading
Inflation Automatic inflation by pump
Deflation Automatic rapid deflation
Power Source Two 1.5V "AAA" alkaline (LR03) batteries
Battery Life Approximately 300 measurements when used twice
daily with alkaline batteries at a room temperature of
23°C
Operating Temperature/ 10°C to 40°C, 30 to 85% RH
Humidity
Storage Temperature/ -20°C to 60°C, 10 to 95% RH
Humidity
Weight of Main Unit Approximately 117 g (not including batteries)
Outer Dimensions 71 mm (w) × 41 mm (h) × 70 mm (d) (not including
the wrist cuff)
Measurable Approximately 13.5 to 21.5 cm
circumference of wrist
Cuff material Nylon
Package Content Main unit, storage case, two "AAA" alkaline (LR03)
batteries, instruction manual, guarantee card, blood
pressure pass
Note: Subject to technical modification without prior notice.
• This OMRON product is produced under the strict quality system of OMRON
HEALTHCARE Co. Ltd., Japan. The Core component for OMRON blood
pressure monitors, which is the Pressure Sensor, is produced in Japan.
• Disposal of this product and used batteries should be carried out in accordance
with the national regulations for the disposal of electronic products.
= Type B
This device fulfils the provisions of EC directive 93/42/EEC (Medical Device
Directive).
This blood pressure monitor is designed according to the European Standard
EN1060, Non-invasive sphygmomanometers Part 1: General Requirements
and Part 3: Supplementary requirements for electromechanical blood pressure
measuring systems.
Please read the instruction manual carefully before
using the device.
HEM-6114-RU_A_M01_100608.pdf
OMRON HEALTHCARE Co., Ltd.
24, Yamanouchi Yamanoshita-cho, Ukyo-ku, Kyoto
615-0084 JAPAN
OMRON HEALTHCARE EUROPE B.V.
Kruisweg 577, 2132 NA Hoofddorp
THE NETHERLANDS
www.omron-healthcare.com
ComplectService Ltd.
13-14 building, 26 B. Tishinskiy per.,
Moscow 123557, RUSSIA
www.csmedica.ru
OMRON (DALIAN) CO., LTD.
Economic & Technical Development Zone
Dalian 116600, CHINA
Made in China