Related Manuals for Husqvarna 324RX-Series
Summary of Contents for Husqvarna 324RX-Series
- Page 1 Operator’s manual (EPA) 324R X-SERIES Please read the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h understand the instructions before using the machine.
-
Page 2: Key To Symbols
Symbols WARNING! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Always wear: • A protective helmet where there is a risk of falling objects •... -
Page 3: Table Of Contents
YOUR WARRANTY RIGHTS AND OBLIGATIONS ... CONTENTS Note the following before starting: Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. Maintenance, replacement, or repair of the emission control devices and system may be performed by any nonroad engine repair establishment or individual. -
Page 4: Safety Instructions
SAFETY INSTRUCTIONS Personal protective equipment IMPORTANT! You must use approved personal protective equipment whenever you use the machine. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your dealer for help in choosing the right equipment. -
Page 5: Cutting Attachment Guard
SAFETY INSTRUCTIONS Cutting attachment guard This guard is intended to prevent loose objects from being thrown towards the operator. The guard also protects the operator from accidental contact with the cutting attachment. WARNING! Never use a cutting attachment without an approved guard. See the chapter on Technical data. -
Page 6: Checking, Maintaining And Servicing The Machine ' S Safety Equipment
SAFETY INSTRUCTIONS WARNING! Bear in mind that: Engine exhaust fumes contain carbon monoxide, which can cause carbon monoxide poisoning. For this reason you should not start or run the machine indoors, or anywhere that is poorly ventilated. The exhaust fumes from the engine are hot and may contain sparks which can start a fire. -
Page 7: Cutting Equipment
SAFETY INSTRUCTIONS • See instructions under the heading Start. Start the machine and apply full throttle. Release the throttle and check that the cutting attachment stops and remains at a standstill. If the cutting attachment rotates with the throttle in the idle position then the carburettor idle setting must be checked. -
Page 8: Cutting Equipment
SAFETY INSTRUCTIONS 2 Keep the teeth of the blade correctly sharpened! Follow our instructions and use the recommended file gauge. An incorrectly sharpened or damaged blade increases the risk of accidents. 3 Maintain the correct blade setting! Follow our instructions and use the recommended blade setting tool. -
Page 9: Sharpening Grass Cutters And Grass Blades
SAFETY INSTRUCTIONS • Make sure that the blade is well supported when you file it. Use a 5.5 mm round file with a file holder. The filing angle is 15 ° . File alternate teeth to the right and • those in between to the left. -
Page 10: General Safety Precautions
SAFETY INSTRUCTIONS General safety precautions IMPORTANT! The machine is only designed for trimming grass, grass clearing and/or forestry clearing. The only accessories you can operate with this engine unit are the cutting attachments we recommend in the chapter on Technical data. Never use the machine if you are tired, if you have drunk alcohol, or if you are taking medication that could affect your vision, your judgement or your co-ordination. -
Page 11: General Working Instructions
SAFETY INSTRUCTIONS • The transport guard must always be fitted to the cutting attachment when the machine is being transported or in storage. WARNING! Take care when handling fuel. Bear in mind the risk of fire, explosion and inhaling fumes. General working instructions IMPORTANT! This section describes the basic safety precautions for... -
Page 12: Basic Working Techniques
SAFETY INSTRUCTIONS Correct balance Let the cutting attachment rest lightly on the ground. If you use a saw blade it should balance about 10 cm above the ground to prevent contact with stones and the like. Adjust the position of the support hook to balance the clearing saw correctly. -
Page 13: Grass Clearing Using A Grass Blade
SAFETY INSTRUCTIONS Grass clearing using a grass blade • Grass blades and grass cutters must not be used on woody stems. • A grass blade is used for all types of tall or coarse grass. • The grass is cut down with a sideways, swinging movement, where the movement from right-to-left is the clearing stroke and the movement from left-to-right is the return stroke. - Page 14 SAFETY INSTRUCTIONS Cutting • The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep the cord parallel to the ground when cutting. Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool.
-
Page 15: What Is What
What is what on the clearing saw? 1 Blade 2 Grease filler cap, bevel gear 3 Bevel gear 4 Cutting attachment guard 5 Shaft 6 Handlebar 7 Throttle control 8 Stop switch 9 Throttle lock 10 Suspension 11 Cylinder cover 12 Starter handle 13 Fuel tank 14 Choke control... -
Page 16: Assembly
Fitting the handlebar • Remove the screw at the rear of the throttle handle. • Slide the throttle handle onto the right side of the handlebar, (see diagram). • Align the screw hole in the throttle handle with the hole in the handlebar. -
Page 17: Fitting A Blade Guard, Grass Blade And Grass Cutter
Fitting a blade guard, grass blade and grass cutter • Hook the blade guard/combination guard (A) onto the fitting on the shaft and secure with the bolt. CAUTION! Use the recommended blade guard. See the Technical data section. • Fit the drive disc (B) on the output shaft. •... -
Page 18: Fitting A Trimmer Guard And Superauto Ii 1" Trimmer Head
arrow in the diagram shows the area where you should operate the socket spanner when loosening or tightening the nut. Fitting a trimmer guard and Superauto II 1" trimmer head • Fit the correct trimmer guard (A) for use with the trimmer head. -
Page 19: Adjusting The Harness And Clearing Saw
Adjusting the harness and clearing WARNING! When using a clearing saw it must always be hooked securely to the harness. Otherwise you will be unable to control the clearing saw safely and this can result in injury to yourself or others. Never use a harness with a defective quick release. -
Page 20: Fuel
When the machine is new the engine oil should be changed after the first month or after 10 hours of operation. • For the best result and function use HUSQVARNA engin oil. • When HUSQVARNA engine oil is not available another high grade engine oil can be used. -
Page 21: Check Before Starting
STARTING AND STOPPING Check before starting • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that the blade has been used with dull teeth. -
Page 22: Warm Engine
STARTING AND STOPPING Warm engine Ignition: Set the stop switch to the start position. Choke: Put the choke in working position. Primer bulb: Press the primer bulb repeatedly until fuel begins to fill the bulb. The bulb need not be completely filled. For throttle handles with a start throttle lock: Set the throttle to the start position by first pressing the throttle... -
Page 23: Maintenance
Carburettor WARNING! The complete clutch cover and shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury. Function • The carburettor governs the engine’s speed via the throttle control. Air and fuel are mixed in the carburettor. The air/fuel mixture is adjustable. -
Page 24: Air Filter
English MAINTENANCE Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact. Put the filter in a plastic bag and pour the filter oil over it. -
Page 25: Sharpening The Saw Blade
• See the cutting attachment packaging for correct sharpening instructions. • Sharpen blades and cutters using a single-cut flat file. • Sharpen all edges equally to maintain the balance of the blade. WARNING! Always discard a blade that is bent, twisted, cracked, broken or damaged in any other way. -
Page 26: Maintenance Schedule
Maintenance schedule Below you will find some general maintenance instructions. Daily maintenance • Check the engine oil level and top up if necessary. • Check throttle trigger and throttle trigger lockout function. • Check that the stop switch works correctly. •... -
Page 27: Specifications
Technical data Engine Cylinder volume, cu.in/cm Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Recommended max. speed, rpm Speed of output shaft, rpm Max. engine output, acc. to ISO 8893, kW/ rpm Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug Electrode gap, inch/mm... - Page 28 324Rx Approved accessories Arbor shaft thread M10 Grass blade/grass cutter Saw blade Plastic blades Trimmer head Support cup 28 – English TECHNICAL DATA Type Cutting attachment guard, Art. no. Grass 255-4 (Ø 255 4 teeth) 503 93 42-02 Grass 255-4 1" (Ø 255 4-teeth) 503 93 42-02 Grass 255-8 (Ø...
-
Page 29: Federal Emission Control Warranty Statement
The warranty period begins on the date small nonroad engine is delivered. LENGTH OF COVERAGE Husqvarna Forest & Garden warrants to the initial owner and each subsequent purchaser that the engine is free from defects in materials and workmanship which cause the failure of a warranted part for a period of two years. - Page 30 Super Auto II Super Auto II 1 " 4,0 m 15 cm ~2,0 m 6 " 6,5 ' 15 cm 6 "...
- Page 32 8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...
- Page 33 4,25 m 4,25 m 15 cm 6" 15 cm 6"...
- Page 34 15 cm 6" ´®z+H9y¶5O¨ ´®z+H9y¶5O¨ 8,5 m 10 cm 4" 4,3 m "Clic"...
- Page 36 1140258-95 ´®z+H9y¶5O¨ ´®z+H9y¶5O¨ 2004-03-29...
Need help?
Do you have a question about the 324RX-Series and is the answer not in the manual?
Questions and answers