Page 1 PORTÉGÉ M300 TOSHIBA PORTÉGÉ M300 Portable Personal Computer User’s Manual...
Page 2 Windows and Microsoft are registered trademarks of Microsoft Corporation. Photo CD is a trademark of Eastman Kodak. Sonic RecordNow! is registered trademarks of Sonic Solutions. Bluetooth is a trademark owned by its proprietor and used by TOSHIBA under license. i.LINK is trademark and registered trademark of Sony Corporation.
Page 3: Fcc Information
Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port, USB port, IEEE1394...
Page 4 User’s Manual EU Declaration of Conformity TOSHIBA declares, that the product: PPM30* conforms to the following Standards: Supplementary “The product complies with the requirements of Information: the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/05/EEC.”...
Page 5 User’s Manual Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121. Germany ATAAB AN005,AN006,AN007,AN009,AN010 and DE03,04,05,08,09,12,14,17 Greece ATAAB AN005,AN006 and GR01,02,03,04...
Page 6: Type Of Service
FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.
Page 7: Fax Branding
User’s Manual Fax branding The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity or individual sending the message and the telephone...
Page 8 User’s Manual The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
Page 9 User’s Manual Notes for use of this device in New Zealand The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers.
Page 10 User’s Manual When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: a person calling your modem will hear a short burst of ringing before the modem answers. This confirms that the call has been successfully switched through the network.
Page 11 User’s Manual General conditions As required by PTC 100, please ensure that this office is advised of any changes to the specifications of these products which might affect compliance with the relevant PTC Specifications. The grant of this Telepermit is specific to the above products with the marketing description as stated on the Telepermit label artwork.
Page 12: Optical Disc Drive Safety Instructions
User’s Manual Optical disc drive safety instructions Be sure to check the international precautions at the end of this section. Panasonic DVD-ROM&CD-R/RW UJDA765 The DVD-ROM&CD-R/RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference.
Page 13 User’s Manual DVD Super Multi UJ-822 The DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
Page 14 User’s Manual International precautions CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.”...
Page 15 User’s Manual OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Page 16 User’s Manual User’s Manual...
Page 17: Table Of Contents
PORTÉGÉ M300 Table of Contents Preface Manual contents ......... xxiii Conventions.
Page 18 Table of Contents Keyboard indicators ........2-10 USB floppy disk drive.
Page 19 DLA for TOSHIBA ........
Page 20 Installing the battery pack ....... . 6-13 TOSHIBA Password Utility ....... . . 6-14 User password .
Page 21 Table of Contents Panel power on/off ........6-17 System Auto Off .
Page 22: Appendix B Display Controller And Modes
TOSHIBA support ........
Page 23: Manual Contents
PORTÉGÉ M300 Preface Congratulations on your purchase of the PORTÉGÉ M300 computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your PORTÉGÉ M300 computer.
Page 24: Conventions
Preface Chapter 4, Operating Basics, includes instructions on using the following devices: Touch Pad, USB floppy disk drive, optical media drives, sound system, modem, Wireless communication features, LAN. It also provides tips on care of the computer, floppy disks and CD/DVDs. Chapter 5, Keyboard, describes special keyboard functions including the keypad overlay and hot keys.
Page 25: Key Operation
Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C.
Page 26 Preface xxvi User’s Manual...
Page 27: General Precautions
PORTÉGÉ M300 General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
Page 28: Pc Card Overheating
- please refer to your User’s Guide or Resource Guide [for TAIS also insert: “or visit the TOSHIBA website at www.pcsupport.toshiba.com] for details). CPU performance may also vary from specifications due to design configuration.
Page 29: Introduction
Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Page 30: Software
If any of the items are missing or damaged, contact your dealer immediately. Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: User’s Manual...
Page 31 Introduction Processor Built-in The computer is equipped with an Intel ® processor. Intel Celeron M processor, which ® ® incorporates a 512 KB level 2 cache memory. Intel Pentium M processor, which ® ® incorporates a 64 KB level 1 cache memory and a 2 MB level 2 cache memory.
Page 32 Introduction Disks Hard disk drive Available in four sizes. 30.0 billion bytes (27.95 GB) 40.0 billion bytes (37.26 GB) 60.0 billion bytes (55.89 GB) 80.0 billion bytes (74.53 GB) 100.0 billion bytes (93.16 GB) USB floppy disk Accommodates either 3 1/2" 1.44-megabyte or drive 720-kilobyte floppy disks.
Page 33 Introduction DVD-ROM&CD-R/RW Some models are equipped with a full-size, DVD- drive ROM&CD-R/RW drive module that lets you run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at maximum 24 speed and CD-RW at maximum 24 speed.
Page 34: Pointing Device
Introduction Display The computer’s LCD display panel supports high-resolution video graphics. The LCD screen can be set at a wide range of viewing angles for maximum comfort and readability. Built-in 12.1” TFT LCD screen 16 M colors, with a resolution of 1024 horizontal × 768 vertical pixels XGA.
Page 35 Introduction Infrared The serial infrared port is compatible with Infrared Data Association (IrDA 1.1) standards. It enables cableless 4 Mbps, 1.152 Mbps, 115.2 kbps, 57.6 kbps, 38.4 kbps, 19.2 kbps or 9.6 kbps data transfer with IrDA 1.1 compatible external devices. Slots PC card The PC card slot accommodate a Type II card.
Page 36 Introduction Communications Modem An internal modem provides capability for data and fax communication. It supports V.90 (V.92). Refer to V.90 section in Appendix E. The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line.
Page 37 Introduction Wireless LAN Some computers in this series are equipped with a Wireless LAN mini-PCI card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard (Revision A, B or G), and Turbo Mode.
Page 38: Special Features
Connects an optional security lock to anchor the computer to a desk or other large object. Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. TOSHIBA Assist...
Page 39 LCD display panel is opened. You can specify the setting in the When I close the lid item of the Setup Action tab in TOSHIBA Power Saver. Low battery When battery power is exhausted to the point that...
Page 40 Introduction Optical media drive Use this to turn the power of the optical media power icon drive on or off. Clicking on the optical media drive icon on the taskbar will turn the power of the optical media drive on or off. If the optical media drive power is off, the disc tray will not open even if the eject button is pushed.
Page 41: Utilities
Buttons: Assign applications to the TOSHIBA Presentation button (default setting is the simultaneous display on LCD and CRT with resolution of 1024 × 768.) and to the TOSHIBA Assist button (default setting is the TOSHIBA Assist). Fn-esse This Windows program lets you define your own “shortcut”...
Page 42 Advanced Port Repricator III. To open the property dialog, select TOSHIBA Mobile Extension from TOSHIBA Assist. TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to allow easy control of communication devices and network connections. TOSHIBA ConfigFree also allows you to find communication problems and create profiles for easy switching between locations and communication networks.
Page 43: Options
A 256, 512 or 1,024 MB memory module (DDR 333) can easily be installed in the computer. Battery pack An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement. High capacity An additional battery pack can be purchased battery pack from your TOSHIBA dealer.
Page 44 Bluetooth preinstalled. It is installed by dealers only. Bluetooth SD card3 Bluetooth SD card is an optional accessory compatible with the SD card slot of this computer. You can buy the card from TOSHIBA dealer. 1-16 User’s Manual...
Page 45: The Grand Tour
PORTÉGÉ M300 Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Certain notebook chassis are designed to accommodate all possible configurations for an entire product series. Your select model may not have all the features and specifications corresponding to all of the icons or switches shown on the notebook chassis, unless you have selected all those features.
Page 46: Left Side
The Grand Tour Display latch This latch secures the LCD panel in its closed position. Push the latch to open the display. Microphone jack A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input. Headphone jack A 3.5 mm mini headphone jack enables connection of stereo headphones.
Page 47: Right Side
The Grand Tour External monitor This external monitor port lets you connect an port external video display. PC card slot The PC card slot can accommodate a Type II card. The slot supports 16-bit PC cards and CardBus PC cards. PC card eject button This is a button for taking out PC card from a PC card slot.
Page 48 The Grand Tour CF Card slot This slot accommodates CompactFlash. You cannot use CompactFlash that does not conform to CompactFlash Association specifications. CF card elect button This is a button for taking out CompactFlash Card from CF card slot. Keep foreign objects out of the CF Card slot. A pin or similar object can damage the computer’s circuitry.
Page 49: Backside
The Grand Tour Backside Figure 2-4 shows the computer’s backside. DC IN 15V jack LAN active indicator (orange) LAN jack Link indicator (green) Figure 2-4 The backside of the computer DC IN 15V jack The AC adaptor connects to this jack. Use only the model of AC adaptor that comes with the computer.
Page 50: Underside
The Grand Tour Underside Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer. Battery lock Battery pack Notches Battery release latch Docking Interface Memory module cover Figure 2-5 The underside of the computer Battery lock Slide this lock to release the battery pack for removal.
Page 51: Front With The Display Open
Stereo speaker (Right) Stereo speaker Microphone (Left) Power button Touch Pad LCD Sensor switch (Not shown) Touch Pad control buttons TOSHIBA Assist TOSHIBA Presentation Button Button Figure 2-6 The front of the computer with the LCD panel open User’s Manual...
Page 52 Hibernation mode. Use the TOSHIBA Power Saver Utility to enable or disable this feature. The default is “enabled”. Refer to the TOSHIBA Power Saver Utility and Panel Power Off/On items in Chapter 1, Special features, for details on settings.
Page 53: System Indicators
LCD and CRT. You can also return to single display by pressing this button twice. The setting of TOSHIBA Presentation button can be changed through the properties of TOSHIBA Controls. Display mode is changed to the multi- monitor display by selecting "Different Image"...
Page 54: Keyboard Indicators
The Grand Tour DC IN The DC IN indicator glows in green when DC power is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes orange. Power The Power indicator glows in green when the computer is on.
Page 55: Usb Floppy Disk Drive
The Grand Tour Caps Lock This indicator glows green when the alphabet keys are locked in uppercase. Arrow mode indicator Numeric mode indicator Figure 2-9 Keypad overlay indicators Arrow mode When the Arrow mode indicator lights green, you can use the keypad overlay (gray labeled keys) as cursor keys.
Page 56: Optical Media Drives
The Grand Tour Floppy disk slot Insert a floppy disk in this slot. Eject button When a floppy disk is fully seated in the drive, the eject button pops out. To remove a floppy disk, push in the eject button and the floppy disk pops out partially for removal.
Page 57: Writable Discs
The Grand Tour Russia, Indian Subcontinent, Africa, North Korea, Mongolia China Writable discs This section describes the types of writable CD/DVD discs. Check the specifications for your drive to for the type of discs it can write. Use RecordNow! to write compact discs. Refer to Chapter 4, Operating Basics.
Page 58: Dvd-Rom&Cd-R/Rw Drive
The Grand Tour DVD-ROM&CD-R/RW drive The full-size DVD-ROM&CD-R/RW drive module lets you record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge.
Page 59: Ac Adaptor
Use only the AC adaptor that came with the computer or an equivalent optional adaptor. Use of any other adaptors could damage your computer. TOSHIBA assumes no liability for any damage in such case. User’s Manual 2-15...
Page 60 The Grand Tour Use only the AC adaptor supplied as an accessory. Other AC adaptors have different voltage and terminal polarities and use of them may produce heat and smoke or even result in fire or rupture. 2-16 User’s Manual...
Page 61: Getting Started
PORTÉGÉ M300 Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: Setting up your work space — for your health and safety Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Page 62: General Conditions
Getting Started General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. Make sure there is adequate space around the computer for proper ventilation. Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible.
Page 63: Seating And Posture
Getting Started Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to figure 3-1. Below eye level 90°angles Foot rest...
Page 64: Work Habits
Getting Started Work habits A key to avoiding discomfort or injury from repetitive strain is to vary your activities. If possible, schedule a variety of tasks into your workday. If you must spend long periods at the computer, finding ways to break up the routine can reduce stress and improve your efficiency.
Page 65 Use only the AC adaptor supplied with your computer or an equivalent adaptor that is compatible. Use of any incompatible adaptor could damage your computer. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor. The supplied power cord conforms to safety rules and regulations in the region the product is bought and should not be used outside this region.
Page 66: Opening The Display
Getting Started 2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the back of the computer. DC IN 15V jack Figure 3-4 Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicators on the front of the computer should glow.
Page 67: Turning On The Power
Getting Started Turning on the power This section describes how to turn on the power. The Power button LED indicates the status. Refer to the Power indicator section in Chapter 6, Power and Power-Up Modes. After you turn on the power for the first time, do not turn it off until you have set up the operating system.
Page 68: Turning Off The Power
Getting Started Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Standby mode. Shut Down mode (Boot mode) When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system’s main screen.
Page 69: Starting Hibernation
For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places: the Hibernate tab in Power Options and Setup Action tab in TOSHIBA Power Saver. Otherwise, the computer will shut down in Standby mode. If battery power becomes depleted, data saved in Standby mode will be lost.
Page 70: Standby Mode
When the AC adaptor is connected, the computer will go into Standby mode according to the settings in the TOSHIBA Power Saver utility. To restore operation from Standby mode, press the power button or press any key. The latter action works only if Wake-up on Keyboard is enabled in HW Setup.
Page 71: Restarting The Computer
1. Click start, click Turn Off Computer and click Stand By. 2. Close the computer’s LCD display panel. This feature must be enabled. Refer to the Setup Action tab in TOSHIBA Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver.
Page 72: Create Optical Recovery Discs
Getting Started Create Optical Recovery Discs A recovery image of your computer is stored on the hard disk. You may use this image to create CD or DVD recovery discs using the following steps: 1. Select either blank CDs or DVD media. 2.
Page 73: Restoring The Preinstalled Software From Your Creating Recovery Media
2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key. 3. Use the left or right cursor key to select the CD-ROM icon in the display menu.
Page 74 Getting Started 3-14 User’s Manual...
Page 75: Operating Basics
PORTÉGÉ M300 Chapter 4 Operating Basics This chapter gives information on basic operations including using the Touch Pad, the USB floppy disk drive (optional in some models), optical media drives, Sound System, Modem, Wireless communication features and LAN. It also provides tips on care of the computer, floppy disks and CD/DVDs.
Page 76: Using The Usb Floppy Disk Drive
Operating Basics You can also tap the Touch Pad to perform functions similar to those of the left button. Click: Tap once Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material.
Page 77: Disconnecting Usb Floppy Disk Drive
Operating Basics Disconnecting USB floppy disk drive When you have finished using the USB floppy disk drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all floppy disk activity has stopped.
Page 78: Loading Discs
Operating Basics Loading discs To load CD/DVDs, follow the steps below and refer to figures 4-3 to 4-6. 1. When the computer’s power is on, press the eject button to open the disc tray slightly. Eject Button Figure 4-3 Pressing the eject button 2.
Page 79: Removing Discs
Operating Basics When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the disc tray. After seating the CD/DVD, however, make sure it lies flat, as shown in figure 4-5.
Page 80: How To Remove Cd/Dvd When The Disk Tray Will Not Open
Operating Basics 2. The CD/DVD extends slightly over the sides of the disc tray so you can hold it. Hold the CD/DVD gently and lift it out. Figure 4-7 Removing a CD/DVD 3. Push the center of the disc tray to close it. Press gently until it locks into place.
Page 81: Writing Cds On Dvd-Rom&Cd-R/Rw Drive
Operating Basics Writing CDs on DVD-ROM&CD-R/RW drive Depending on the type of drive installed, you may be able to write CDs. The DVD-ROM&CD-R/RW drive lets you write as well as read CD-ROMs. Observe the precautions in this section to ensure the best performance for writing CDs.
Page 82: When Writing Or Rewriting
Operating Basics TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. The actual number of rewrites to CD-RW is affected by the quality of the disc and the way it is used.
Page 83: Writing Cd/Dvds On Dvd Super Multi Drive
Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.
Page 84 Operating Basics CD-R: TAIYO YUDEN CO., LTD. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd. CD-RW: (Multi-Speed and High-Speed) MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. CD-RW: (Ultra-Speed) MITSUBISHI CHEMICAL CORPORATION DVD-R: DVD Specifications for Recordable Disc for General Version 2.0 TAIYO YUDEN CO., LTD.
Page 85 Operating Basics This drive cannot use discs that allow writing faster than 2 speed (DVD-R, DVD-RW, DVD-RAM), 2.4 speed (DVD+R, DVD+RW). If the disc is poor in quality, dirty or damaged, writing or rewriting errors may occur. Be careful to check the disc for dirt or damage before you use it.
Page 86: When Writing Or Rewriting
Always copy data from the HDD to the DVD-RAM. Do not use cut-and- paste. The original data will be lost if there is a write error. RecordNow! Basic for TOSHIBA Note the following limitations when you use RecordNow!: DVD-Video cannot be created using RecordNow!.
Page 87: Data Verification
Operating Basics You cannot back up a CD-ROM or CD-R/RW to DVD-R/-RW or DVD+R/+RW using the “Exact Copy” function of RecordNow!. You cannot back up DVD-ROM, DVD-Video or DVD-R/-RW or DVD+R/ +RW to CD-R/RW using the “Exact Copy” function of RecordNow!. RecordNow! cannot record in packet format.
Page 88: Dla For Toshiba
Operating Basics DLA for TOSHIBA Note the following limitations when you use DLA: This software supports only rewritable discs (DVD+RW, DVD-RW, and CD-RW). It does not support DVD+R, DVD-R, and CD-R discs that are not rewritable. DLA does not support formatting a DVD-RAM disc and writing to it.
Page 89: How To Make A Dvd-Video
Operating Basics How to make a DVD-Video Simplified steps for making a DVD-Video from video data captured from a DV-Camcorder: 1. Click [Start]-[All Programs] - [InterVideo WinDVD Creator2] - [InterVideo WinDVD Creator] to launch WinDVD Creator. 2. Click [Capture] button then capture the video data from the DV- Camcorder via IEEE1394.
Page 90 Operating Basics While recording video to DVD or tape, please close all other programs. Do not run software like a screen saver because it can put a heavy load on the CPU. Do not run communication applications like a modem or a LAN. 2.
Page 91: Media Care
Operating Basics If you use an over-used rewritable disc, the full formatting might be locked. Please use a brand new disc. Media care This section provides tips on protecting data stored on your CD/DVDs and floppy disks. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1.
Page 92: Sound System
Operating Basics Sound System This section describes audio controls including sound levels and power management. Volume Control The Volume Control utility lets you control the audio volume in Windows for both playback and recording. To launch Volume Control for playback, click start, point to All Programs, point to Accessories, point to Entertainment and click Volume Control.
Page 93: Modem
To select a region, follow the steps below. 1. Click start, point to All Programs, point to TOSHIBA, point to Networking and click Modem Region Select. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.
Page 94: Modem Selection
Operating Basics AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection.
Page 95: Disconnecting
Operating Basics 2. Plug the other end of the modular cable into a telephone jack. Modular cable Modem jack Telephone jack Figure 4-9 Connecting the internal modem Do not pull on the cable or move the computer while the cable is connected.
Page 96: Wireless Lan
TOSHIBA strongly recommend the customer to enable the WEP function. TOSHIBA is not liable for the eavesdropping of data due to the use of Wireless LAN and the damage thereof. 4-22...
Page 97: Bluetooth Wireless Technology
Please refer also to the electronic information which is included with each software. This Bluetooth Stack is based on Bluetooth Version 1.1/1.2 specification. TOSHIBA cannot confirm all compatibility among any PC products and/or other electronic devices using Bluetooth other than TOSHIBA mobile PCs. User’s Manual...
Page 98: Wireless Communication Switch
TOSHIBA 1. Install: ® On Windows2000 or Windows XP, Bluetooth Stack for Windows TOSHIBA does not need signature. 2. Fax application software: Regarding FAX application software, there are some software that you cannot use on this Bluetooth Stack. 3. Multi User: On Windows XP, Multi user does not supported.
Page 99: Wireless Communication Indicator
Operating Basics Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indication Indicator off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction Indicator glows Wireless communication switch is on. Wireless LAN or Bluetooth is turned on by an application.
Page 100: Connecting Lan Cable
Operating Basics Connecting LAN cable To connect the LAN cable, follow the steps below. Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up.
Page 101: Cleaning The Computer
Operating Basics Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again.
Page 102: Heat Dispersal
CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver. Maximum Turns on the fan first, then if necessary, lowers the CPU Performance processing speed.
Page 103: The Keyboard
PORTÉGÉ M300 Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/ 102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with.
Page 104: Function Keys: F1
Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
Page 105: Hot Keys
The Keyboard Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to Keypad overlay section in this chapter for more information on how to operate these keys.
Page 106 Fn, and release and press F2 again to toggle between the settings. Release both Fn and F2 to put the new setting into effect. You can also change this setting through the Profile options in TOSHIBA Power Saver.
Page 107 You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver. The brightness level is always set at the maximum value for about 18 seconds, when the internal LCD screen turns on.
Page 108: Fn Sticky Key
Fn key. Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an “F number” key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Accessibility.
Page 109: Windows Special Keys
The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows: Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button.
Page 110: Temporarily Using Normal Keyboard (Overlay On)
The Keyboard Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys in figure 5-2. Press Fn + F11 again to turn off the overlay. Figure 5-2 The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard...
Page 111: Temporarily Changing Modes
The Keyboard Temporarily changing modes If the computer is in Numeric mode, you can switch temporarily to Arrow mode by pressing a shift key. If the computer is in Arrow mode, you can switch temporarily to Numeric mode by pressing a shift key. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation.
Page 112 The Keyboard 5-10 User’s Manual...
Page 113: Power And Power-Up Modes
PORTÉGÉ M300 Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Page 114 Power and Power-Up Modes Table 6-1 Power conditions continued Power on Power off (no operation) Battery charge • Operates adaptor is above low • LED: Battery off battery trigger DC IN off connected point Battery charge • Operates is below low •...
Page 115: Power Indicators
Power and Power-Up Modes Power indicators As shown in the above table, the Battery, DC IN and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status. Battery indicators Check the Battery indicator to determine the status of the battery pack. The following indicator lights indicate the battery status: The battery charge is low.
Page 116: Power Indicator
Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. Do not remove the battery pack while the computer is in Standby mode. Data is stored in RAM, so if the computer loses power it will be lost.
Page 117: High Capacity Battery Pack (Option)
The computer’s RTC battery is a lithium ion battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations.
Page 118: Care And Use Of The Battery Pack
Power and Power-Up Modes Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance.
Page 119 Never use the computer again until it has been checked by a TOSHIBA service provider. It might generate smoke or fire, or the battery pack might rupture. 3. Make sure the battery is securely installed in the computer before attempting to charge the battery pack.
Page 120: Charging The Batteries
The Battery indicator glows orange when the battery is being charged. Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger.
Page 121: Battery Charging Notice
Power and Power-Up Modes Time The following table shows the approximate time required to fully charge a discharged battery. Charging time (hours) Battery type Power on Power off High capacity battery pack (8800mAh) about 6.0 to 9.0 about 4.5 Battery pack (4700mAh) about 4.0 to 5.5 about 3.0 RTC battery...
Page 122: Monitoring Battery Capacity
Therefore, an often used, older battery will not operate for as long as a new battery even when both are fully charged. In this case, TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery.
Page 123: Retaining Data With Power Off
Power and Power-Up Modes The condition of the battery terminals. Make sure the battery terminals stay clean by wiping them with a clean dry cloth before installing the battery pack. Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Retention time Battery type...
Page 124: Replacing The Battery Pack
Power and Power-Up Modes If you are not going to use the computer for more than eight hours, disconnect the AC adaptor. Store spare battery packs in a cool dry place out of direct sunlight. Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one.
Page 125: Installing The Battery Pack
7. Return your computer to the upright position. For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to your TOSHIBA dealer. Installing the battery pack To install a battery pack, follow the steps below.
Page 126: Toshiba Password Utility
Figure 6-2 Securing the battery cover 6. Return your computer to the upright position. TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows password.
Page 127 If an unformatted card or one with an incompatible format is inserted, you will be prompted to format it with a tool named TOSHIBA SD Memory Card Format. To start the format tool, point to or click the following items: start ->...
Page 128: Supervisor Password
Register, delete or change the supervisor password. Create or invalidate a supervisor password token. This function in the TOSHIBA Password Utility lets you invalidate only supervisor tokens or all tokens, including user and supervisor tokens. Specify restrictions for general users.
Page 129: Windows Utilities
Power and Power-Up Modes Windows utilities You can specify the setting in TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Standby mode and Fn + F4 to enter Hibernation. Refer to Chapter 5, The Keyboard for details.
Page 130 Power and Power-Up Modes 6-18 User’s Manual...
Page 131: Hw Setup
PORTÉGÉ M300 Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer. TOSHIBA HW Setup lets you configure settings for General, Display, Boot Priority, Keyboard, CPU, LAN, Device Config, Parallel/Printer and USB.
Page 132: Boot Priority
HW Setup General This window displays the BIOS version and contains two buttons: Default and About. Return all HW Setup values to the factory Default settings. Display the HW Setup version. About Setup This field displays BIOS Version and date. Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor.
Page 133 HW Setup HDD −> FDD −> CD- The computer looks for bootable files in the ROM −> LAN following order: HDD, floppy disk drive* , CD- ROM* and LAN (Default). HDD −> CD-ROM −> The computer looks for bootable files in the LAN −>...
Page 134 HW Setup 3. Use the left/right cursor keys to highlight the boot device you want and press Enter. If a supervisor password is set only, it is the following. The menu above appear when you use the user password to start the computer (able to run HW Setup).
Page 135 HW Setup If you select Left Ctrl + Left Alt or Right Ctrl + Right Alt for this option, you cannot use the selected keys to reboot the computer in combination with the Del key. For example, if you select Left Ctrl + Left Alt, you must use Right Ctrl, Right Alt and Del to reboot the computer.
Page 136: Device Config
HW Setup Wake-up on LAN This feature lets the computer’s power be turned on when it receives a wake-up signal from the LAN. Enables Wake-up on LAN. Enabled Disables Wake-up on LAN. (Default) Disabled Do not install or remove an optional memory module while Wake-up on LAN is enabled.
Page 137 HW Setup Parallel Port Mode The options in this tab are ECP and Standard Bi-directional. Sets the port type to Extended Capabilities Port (ECP). For most printers, the port should be set to ECP (Default). This setting should be used with some other Standard parallel devices.
Page 138 HW Setup User’s Manual...
Page 139: Optional Devices
PORTÉGÉ M300 Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory PC card SD card CF (CompactFlash) card...
Page 140: Pc Card
The computer is equipped with a PC card slot that can accommodate a Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.
Page 141: Sd Card
SD memory cards are sold with format in conformity to the Standards of SD memory card. If you format the SD card again, be sure to format it with the utility of TOSHIBA SD memory card format, not in the format defined as the Windows standard format.
Page 142: Inserting An Sd Card
Optional Devices Inserting an SD card To insert an SD card, follow the steps below. 1. Insert an SD card in the SD card slot. 2. Press gently to ensure a firm connection. SD card SD card slot Figure 8-3 Inserting an SD card Make sure the SD card is oriented properly before you insert it.
Page 143: Sd Card Care
8. Do not touch the metal part or expose it to liquids or let it get dirty. Creation of a boot disk In TOSHIBA SD Memory Boot Utility, a boot disk can be created with SD memory card. Refer to the Utilities of Chapter 1, Introduction for details.
Page 144: Inserting A Cf Card
Optional Devices Inserting a CF card To insert a CF card, follow the steps below. 1. Press the CF card eject button to extend it. 2. Press the extended eject button to pop the Dummy card out slightly. 3. Insert the CF card into the slot. 4.
Page 145: Cf Card Care
When you remove a memory, please do not touch other portions of a computer. Use only memory modules approved by TOSHIBA. Do not try to install or remove a memory module under the following conditions. You can damage the computer and the module. Also, data will be lost.
Page 146: Installing Memory Module
Optional Devices Use a point size 0 Phillips screwdriver to remove and fasten the screws. Use of an incorrect screwdriver can damage the screw heads. Installing memory module Follow the steps below to install a memory module. 1. Set the computer to boot mode and turn the computer’s power off. Make sure the Power indicator is off.
Page 147: Removing Memory Module
Optional Devices Be careful not to drop the screw inside the computer. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. 7. Seat the memory module cover and secure it with one screw. 8.
Page 148: Battery Pack
Optional Devices 7. Grasp the module by the sides and pull it out. If you use the computer for a long time, the memory modules and the circuits located close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. Do not touch the connectors on the memory module or on the computer.
Page 149: Usb Floppy Disk Drive
Optional Devices USB floppy disk drive The USB floppy disk drive module can be connected to the USB port. For details on connecting the USB floppy disk drive module, refer to Chapter 4, Operating Basics. External monitor An external analog monitor can be connected to the external monitor port on the computer.
Page 150: I.link (Ieee1394)
There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise.
Page 151: Connecting
Optional Devices Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. i.LINK (IEEE1394) connector i.LINK (IEEE1394) port Figure 8-14 Connecting the i.LINK(IEEE1394) cable into the computer 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: You may need to install drivers for your i.LINK devices.
Page 152: Advanced Port Replicator Iil
Optional Devices Advanced Port Replicator IIl In addition to the ports available on the computer, the Advanced Port Replicator lll provides serial port and separate ports for PS/2 mouse and PS/2 keyboard. The Advanced Port Replicator connects directly to the docking interface on the underside of the computer.
Page 153: Parallel Printer
7. Turn on the computer’s power. 8. Start the HW Setup program. Refer to Chapter 7, Setup. 9. Select the Parallel/Printer tab from the TOSHIBA HW Setup window. 10. Set the Parallel Port Mode and press OK. 11. Choose Reboot for the change to take effect.
Page 154 Optional Devices 2. Align the holes for the security lock and attach the lock. Security lock slot Figure 8-15 Security lock 8-16 User’s Manual...
Page 155: Troubleshooting
PORTÉGÉ M300 Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.
Page 156: Preliminary Checklist
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. Make sure you turn on all peripheral devices before you turn on the computer.
Page 157: Hardware And System Checklist
Troubleshooting Software The problems may be caused by your software or disk. If you cannot load a software package, the media may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation.
Page 158: Power
This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: The computer stops and does not proceed to display information or messages except the TOSHIBA logo.
Page 159: Ac Power
Troubleshooting AC power If you have trouble turning on the computer with the AC adaptor connected, check the DC IN indicator. Refer to Chapter 6, Power and Power-Up Modes for more information. Problem Procedure AC adaptor doesn’t Check the connections. Make sure the cord is power the computer firmly connected to the computer and a power (DC IN indicator does...
Page 160 Fully discharge the battery, then try to charge it again. Check the power consumption settings in TOSHIBA Power Saver utility. Consider using a power saving mode. User’s Manual...
Page 161: Password
Password Problem Procedure Cannot enter Refer to the TOSHIBA Password Utility section in password Chapter 6, Power and Power-Up Modes. Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, Keyboard.
Page 162: Internal Lcd Display Panel
Troubleshooting Internal LCD display panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, Setup, for more information. Problem Procedure No display Press hotkeys Fn + F5 to change the display priority, to make sure it is not set for an external monitor.
Page 163: Dvd-Rom&Cd-R/Rw Drive
Troubleshooting DVD-ROM&CD-R/RW drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a Make sure the drive’s disc tray is securely CD/DVD in the drive closed. Press gently until it clicks into place. Check whether the drive power is on. If the power is off, click on the optical media drive icon in the task tray and turn on the power.
Page 164: Dvd Super Multi Drive
Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: Use only media recommended by TOSHIBA. Do not use the mouse or keyboard during writing. Use only the software supplied with the computer for recording.
Page 165: Usb Floppy Disk Drive
Troubleshooting Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: CD-DA, CD-Text, Photo CD (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), Addressing Method 2 Check the region code on the DVD. It must match that on the DVD Super Multi drive.
Page 166: Pc Card
Troubleshooting PC card Refer also to Chapter 8, Optional Devices. Problem Procedure PC card error occurs Reseat the PC card to make sure it is firmly connected. Make sure the connection between the external device and the card is firm. Check the card’s documentation.
Page 167: Pointing Device
Troubleshooting Pointing Device If you are using a USB mouse, also refer to the section in this chapter and to your mouse documentation. Touch Pad Problem Procedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to standby its Pad operation normal shape and try again to move it.
Page 168: Usb Mouse
Troubleshooting USB mouse Problem Procedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to resume its mouse operation normal shape and try again to move it. Make sure the mouse is properly connected to the USB port.
Page 169: Usb
Troubleshooting Refer also to your USB device’s documentation. Problem Procedure USB device does not Check for a firm cable connection between the work USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed.
Page 170: Sound System
Troubleshooting Sound System Refer also to documentation for your audio devices. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Check Windows Device Manager.
Page 171: I.link (Ieee1394)
Troubleshooting i.LINK (IEEE1394) Problem Procedure i.LINK device does not Make sure the cable is securely connected to the function computer and to the device. Make sure the device’s power is turned on. Reinstall the drivers. Open the Windows Control Panel and double-click the Add Hardware icon.
Page 172: Lan
Troubleshooting Problem Procedure Character display In data transmission, make sure the parity bit and becomes garbled stop bit settings correspond with those of the during a remote computer. communication Check the flow control and communication protocol. You cannot receive an Check the rings before auto answer setting in incoming call your communications application.
Page 173: Bluetooth
Troubleshooting Bluetooth For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Make sure the computer’s wireless Bluetooth device communication switch is set to on. Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on. Make sure no optional Bluetooth PC card and Bluetooth SD card are installed in the computer.
Page 174: Toshiba Support
Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.
Page 175: Where To Write
Troubleshooting Where to write If you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed below: Outside of Europe In Europe Australia Germany & Austria TOSHIBA Australia Pty. Ltd.
Page 176 TOSHIBA Information Systems Systems, Inc. (U.K.) Ltd. 9740 Irvine Boulevard TOSHIBA Court Irvine, California 92618 Weybridge Business Park Addlestone Road Weybridge, Surrey KT15 2UL The Rest of Europe TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm 8, D-41460 Neuss, Germany 9-22 User’s Manual...
Page 177: Appendix A Specifications
PORTÉGÉ M300 Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size 286.0 (w) × 233.0 (d) × 28.9/32.9(h) millimeters (not including parts that extend beyond the main body) Refer to User’s Manual about Weight. Environmental Requirements Conditions Ambient temperature Relative humidity...
Page 178 Specifications Computer 15 VDC 3.0 amperes Built-in Modem Network control unit (NCU) Type of NCU Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications Communication Data: Full duplex system...
Page 179 Specifications Input/output 600 ohms ±30% impedance Error correcting MNP class 4 and ITU-T V.42 Data compression MNP class 5 and ITU-T V.42bis Power supply +3.3V (supplied by computer) User’s Manual...
Page 180 Specifications User’s Manual...
Page 181: Appendix B Display Controller And Modes
PORTÉGÉ M300 Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Extended Graphics Array (XGA) support for the internal LCD and external monitors.
Page 182 Display Controller and Modes Table1 Video modes (VGA) Video Type Resolution Character Scanning mode matrix colors colors frequency (pels) Vertical (Hz) 0, 1 40 × 25 8 × 8 16 of 256K 16 of 256K Text Characters 2, 3 80 × 25 8 ×...
Page 183 Display Controller and Modes Table1 Video modes (VGA) continued Video Type Resolution Character Scanning mode matrix colors colors frequency (pels) Vertical (Hz) 320 × 200 8 × 8 16 of 256K 16 of 256K Grph Pels 640 × 200 8 × 8 16 of 256K 16 of 256K Grph...
Page 184 Display Controller and Modes Table 2 Video modes Resolution Vertical colors colors frequency (Hz) 640 × 480 256/256K 256/256K 800 × 600 256/256K 256/256K 1024 × 768 256/256K 256/256K 1280 × 1024 256/256K 256/256K (Virtual) 1400 × 1050 256/256K 256/256K (Virtual) 1600 ×...
Page 185 Display Controller and Modes Table 2 Video modes continued Resolution Vertical colors colors frequency (Hz) 640 × 480 64K/64K 64K/64K 800 × 600 64K/64K 64K/64K 1024 × 768 64K/64K 64K/64K 1280 × 1024 64K/64K 64K/64K (Virtual) 1400 × 1050 64K/64K 64K/64K (Virtual) 1600 ×...
Page 186 Display Controller and Modes Table 2 Video modes continued Resolution Vertical colors colors frequency (Hz) 640 × 480 16M/16M 16M/16M 800 × 600 16M/16M 16M/16M 1024 × 768 16M/16M 16M/16M 1280 × 1024 16M/16M 16M/16M (Virtual) 1400 × 1050 16M/16M 16M/16M (Virtual) 1600 ×...
Page 187: Display Settings
Display Controller and Modes Display settings 1. You cannot move from the [Settings] tab of [Display Properties] to the multi-monitor when you are using the display of the computer and an external CRT display or a TV at the same time. *The [Settings] tab is displayed in the following steps;...
Page 188 Display Controller and Modes 3) Select either Monitor (CRT display) or Television, then select Apply button, because the Primary Device is fixed into Notebook (the display of the computer). Figure B-2 Intel(R) 82852/82855 GM/GME Graphics Controller Prope...(1) 2. Some reproduced DVD picture may not be displayed when the display of the computer and a CRT display are used at the same.
Page 189 PORTÉGÉ M300 Appendix C AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software.
Page 190 AT Commands Communication standard setting This command determines the communication standard CCITT or Bell. Selects CCITT V.22 mode when the modem is at 1200 bps. Selects Bell 212A when the modem is at 1200 bps (default). Selects V.21 when the modem is at 300 bps. Selects Bell 103J when the modem is at 300 bps (default).
Page 191 AT Commands Result Codes: n=0,1 ERROR Otherwise Hook control This command instructs the modem to go on-hook to disconnect a call, or off-hook to make the phone line busy. Modem goes on-hook (default). Modem goes off-hook. Result Codes: n=0,1 ERROR Otherwise Request ID information This command displays product information about the modem.
Page 192 AT Commands Modulation handshake This command controls whether or not the local modem performs a negotiated handshake at connection time with the remote modem when the communication speed of the two modems is different. When originating or answering, this is for handshake only at the communication standard specified by S37 and the ATB command.
Page 193 AT Commands Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric equivalents.
Page 194 AT Commands Dial tone detect Disabled: The modem dials a call regardless of whether it detects a dial tone. Enabled: The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds.
Page 195 AT Commands &D2 If the DTR signal is not detected while in on-line data mode, the modem disconnects (default). &D3 Reset on the on-to-off DTR transition. Result Codes: n=0,1,2,3 ERROR Otherwise &F Load factory settings This command loads the configuration stored and programmed at the factory.
Page 196 AT Commands &Tn Self-test commands These tests can help to isolate problems if you experience periodic data loss or random errors. &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE.
Page 197 AT Commands V.42, MNP, or buffered (default). The modem attempts to connect in V.42 error control mode. If this fails, it attempts to connect in MNP mode. If this fails, it connects in buffer mode and continues operation. This is also known as V.42/MNP auto reliable mode (same as &Q5).
Page 198 AT Commands Result Codes: n=0,3 ERROR Otherwise C-10 User’s Manual...
Page 199 PORTÉGÉ M300 Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connection fails.
Page 200 S-registers Ring counter This register is read only. The value of S1 is incremented with each ring. If no ring occurs over a six-second interval, this register is cleared. Range: 0-225 Default: 0 Units: rings AT escape character (user defined) This register determines the ASCII values used for an escape sequence.
Page 201 S-registers Command line editing character (user defined) This register sets the character recognized as a backspace and pertains to asynchronous only. The modem will not recognize the backspace character if it is set to a value that is greater than 32 ASCII.
Page 202 S-registers Comma pause time This register sets the time, in seconds, that the modem must pause when it encounters a comma (,) in the dial command string. In some countries/regions, S8 will set both wait before dialing and comma pause time. Range: 0-255 Default: 2 Units:...
Page 203 S-registers S37 Dial line rate S37 = 0 (default) maximum modem speed S37 = 1 reserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 reserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37 = 8...
Page 204: At Command Set Result Codes
S-registers AT command set result codes The following table shows the result codes. The result code summary Result Code Numeric Description Command executed CONNECT Modem connected to line RING A ring signal has been detected NO CARRIER Modem lost carrier signal, or does not detect carrier signal, or does not detect answer tone...
Page 205 S-registers CONNECT 33600 EC* Connection at 33600 bps DELAYED* Delay is in effect for the dialed number BLACKLISTED* Dialed number is blacklisted BLACKLIST FULL* Blacklist is full *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V.42bis - V.42 error control and V.42bis data compression.
Page 206 S-registers User’s Manual...
Page 207 PORTÉGÉ M300 Appendix E V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably.
Page 208 V.90 Table E-1 Result codes for a V.90 connection Result code Description CONNECT 32000 EC* Connection at 32000 bps CONNECT 36000 EC* Connection at 36000 bps CONNECT 40000 EC* Connection at 40000 bps CONNECT 44000 EC* Connection at 44000 bps CONNECT 48000 EC* Connection at 48000 bps CONNECT 52000 EC*...
Page 209 V.90 * EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V.42 error control and V.42bis data compression V.42 error control only NoEC No error control protocol...
Page 210 V.90 User’s Manual...
Page 211: Card Specifications
PORTÉGÉ M300 Appendix F Wireless LAN Card Specifications Form Factor Mini PCI Type III IEEE 802.11 Standard for Wireless LANS Compatibility Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance. Microsoft Windows Networking ®...
Page 212: Radio Characteristics
Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions.
Page 213 Wireless LAN Wireless IEEE 802.11 Channels Sets (Revision B and G) Frequency Range 2400-2483.5 MHz Channel ID 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457* 2462 2467* 2472* *1 Factory-set default channels *2 Refer to the sheet Approved Countries/Regions for use for the countries/ regions that in which these channels can be used.
Page 214 Wireless LAN Wireless IEEE 802.11 Channels Sets (Revision A) Frequency Range 5150-5850 MHz Channel ID 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5745 5765 User’s Manual...
Page 215 Wireless LAN 5785 5805 Wireless Channels Sets (Turbo Mode) Frequency Range 2400-2483.5 MHz Note Channel ID 2437 US only * *3 These channels are available to Atheros module type only. Wireless Channels Sets (Turbo Mode) Frequency Range 5150-5850 MHz Note Channel ID 5210 US only *...
Page 216 Wireless LAN User’s Manual...
Page 217 Bluetooth wireless technology Interoperability Bluetooth Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: Bluetooth Specification Ver.1.2, as defined and approved by The Bluetooth Special Interest Group.
Page 218 TOSHIBA portable computers. Always use Bluetooth Cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe...
Page 219: Bluetooth Wireless Technology And Your Health
Because products with Bluetooth wireless technology operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Bluetooth wireless technology is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
Page 220 Bluetooth Card from TOSHIBA has to be operated while maintaining a minimum body to antenna which are located on top of LCD distance of 20 cm. Refer to the Regulatory Statements as identified in the documentation that comes with those products for additional information.
Page 221 Relevant transmitters include FCC IDs: CJ6UPA3375WL, CJ6UPA3232BT Changes or modifications made to this equipment not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user’s authority to operate the equipment. Taiwan Article 14 Unless approved, for any model accredited low power radio...
Page 222 2. In case that RF interference occurs to Other Radio Stations from this equipment, please change promptly the frequency for use, place to use, or stop emitting Radio. 3. Please contact TOSHIBA Direct PC if you have a problem, such as interference from this equipment to Other Radio Stations.
Page 223: Device Authorization
Bluetooth wireless technology Interoperability 3. TOSHIBA Direct PC Monday - Friday: 10:00-17:00 Toll Free Tel : 0120-13-1100 Direct Dial : 03-3457-5916 : 03-5444-9450 Device Authorization This device obtains the Technical Regulation Conformity Certification and the Technical Conditions Compliance Approval, and it belongs to the...
Page 224: Wireless Technology
Bluetooth wireless technology Interoperability Approved Countries/Regions for use (Bluetooth wireless technology) Bluetooth Card from TOSHIBA equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Page 225: Ac Power Cord And Connectors
PORTÉGÉ M300 Appendix H AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters...
Page 226 AC Power Cord and Connectors France: LCIE Switzerland: Germany: United Kingdom: In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 2- 15P (250V) or 1-15P (125V) and three pin plug configuration must be 6- 15P (250V) or 5-15P (125V) as designated in the U.S.
Page 227: Parts Numbers
PORTÉGÉ M300 Appendix I Parts Numbers The computer configuration and parts numbers, printed on a label on the bottom of the computer, indicate the CPU, LCD, memory, HDD and communication devices. Configurations The following table shows the computer configuration indicated on a label. Shaded areas indicate abbreviations used on the label.
Page 228 Parts Numbers Communication 802.11g without BT Antenna 802.11g with BT Antenna WLg/BTA 802.11a/g combo without BT Antenna WLag 802.11a/g combo with BT Antenna WLag/BTA 802.11g/BT integrated WLg/BT 802.11a/g combo/BT integrated WLag/BT Wireless LAN Antenna and BT Antenna only WLA/BTA Wireless LAN Antenna without BT Antenna User’s Manual...
Page 229 PORTÉGÉ M300 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP: accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange BIOS: basic input output system CD-ROM: Compact Disc-Read Only Memory CD-RW: Compact Disc-ReWritable...
Page 230 Glossary IrDA: Infrared Data Association IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MB: megabyte MS-DOS: Microsoft Disk Operating System OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory...
Page 231 Glossary analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements.
Page 232 Glossary bus: An interface for transmission of signals, data or electric power. byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. cache memory: High speed memory which stores data that increases processor speed and data transfer rate.
Page 233 Glossary compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component.
Page 234 Glossary delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information.
Page 235 (FDD): An electromechanical device that reads and writes to floppy disks. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk.
Page 236 Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator panel.
Page 237 Glossary jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte.
Page 238 Glossary mode: A method of operation, for example, the boot mode, standby mode or the hibernation mode. modem: Derived from modulator/demodulator, a device that converts (modulates) digital data for transmission over telephone lines and then converts modulated data (demodulates) to digital format where received.
Page 239 The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver Utility: A TOSHIBA utility that lets you set the parameters for various power-saving functions. printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached.
Page 240 Glossary restart: Resetting a computer without turning it off (also called “warm boot” or “soft reset”). See also boot. RGB: Red, green, and blue. A device that uses three input signals, each activating an electron gun for a primary additive color (red, green, and blue) or port for using such a device.
Page 241 TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
Page 242 Glossary Glossary-14 User’s Manual...
Page 243 6-11 controller 1-6 indicator 2-10 hinge 2-8 location 2-6 opening 3-6 monitoring capacity 6-10 DLA for TOSHIBA 1-15 4-14 real time clock 1-3 Docking interface 1-6 safety precautions 6-6 Documentation list 1-2 save mode 1-11 DVD Super Multi drive 1-5...
Page 244 Index Equipment setup display brightness increase general conditions 3-2 placement 3-2 display selection 5-5 Ergonomics instant security 5-4 lighting 3-3 power save mode 5-4 seating and posture 3-3 sound mute 5-3 work habits 3-4 standby 5-4 wireless setting 5-5 HW Setup 1-13 Floppy disk care 4-17 accessing 7-1 Fn + Ctrl (enhanced keyboard...
Page 245 Index Numeric mode 5-8 temporarily using normal Password keyboard (overlay power on 1-10 on) 5-8 problems 9-7 temporarily using overlay starting the computer by 6- (overlay off) 5-8 turning on the overlays 5-7 Supervisor 6-16 user 6-14 LAN 1-8 4-25 PC card 1-7 cable types 4-25 inserting 8-2...
Page 246 TOSHIBA ConfigFree 1-14 TOSHIBA Controls 1-13 System start-up 9-3 TOSHIBA Mobile Extension 1- Touch Pad 9-13 USB 9-15 TOSHIBA PC Diagnostic Tool 1- USB floppy disk drive 9-11 Wireless LAN 9-18 TOSHIBA Power Saver 1-13 Processor 1-3 TOSHIBA Presentation button...
Page 247 Index USB 1-6 location 2-2 problems 9-15 USB floppy disk drive 1-4 additional 8-11 problems 9-11 using 4-2 Video modes B-1 Video RAM 1-3 Volume control 2-2 Wireless communication 4-21 indicator 2-10 4-25 switch 1-9 4-24 Wireless LAN 1-9 4-22 problems 9-18 User’s Manual Index-5...
Page 248 Index Index-6 User’s Manual...

Toshiba Portege M300 User Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Toshiba Portege M300

Summary of Contents for Toshiba Portege M300

Table of Contents