1. Manuals
  2. Brands
  3. Huffy Manuals
  4. Fitness Equipment
  5. Sports Basketball Systems
  6. Owner's manual

Huffy Sports Basketball Systems Owner's Manual

Inground system
Hide thumbs

Advertisement

Table of Contents

© COPYRIGHT 2000 by HUFFY SPORTS
Inground System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
WARNING!
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO PROPERTY.
Toll-Free Customer Service Number for U.S: 1-800-558-5234,
For Canada: 1-800-284-8339,
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia: 1-800-333 061
Internet Address: http://www.huffysports.com

REQUIRED TOOLS AND MATERIALS:

• Two People
• Tape
• Carpenter's Level
• Wood Scrap
• Wedge
• Phillips Head Screw Driver
• Concrete, 540 lb (245 kg) Minimum and Container to Mix
• Wood Board (Scrap)
• Wrenches: (Two) 7/16", 1/2", 9/16", 3/4" or two Large and Small
Adjustable Wrenches
• Tape Measure
• Shovel and Spade
• Hammer
• Sawhorse or Support Table
• Step Ladder 8 ft. (2.4 m)
• Safety Goggles
1
02/04
P/N 21145507

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Sports Basketball Systems and is the answer not in the manual?

Questions and answers

Related Manuals for Huffy Sports Basketball Systems

Summary of Contents for Huffy Sports Basketball Systems

  • Page 1 COULD RESULT IN INJURY OR DAMAGE TO PROPERTY. Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Europe: 00 800 555 85234 (Sweden: 009 555 85234), © COPYRIGHT 2000 by HUFFY SPORTS Inground System Owners Manual Customer Service Center • Two People •...
  • Page 2 BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular motion to ream out Pour garantir l'utilisation optimale du panneau, les composants du système élévateur et la visserie doivent être bien ajustés (serrés).
  • Page 3 WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NOT HANG on the rim or any part of the system including backboard, support braces or net.
  • Page 4 20 ft. (7 m) radius of pole location. • Climate, corrosion, excessive use, or misuse could result in system failure. • If technical assistance is required, contact Huffy Sports. • Minimum operational height is 6'6" (1.98 m) to the bottom of backboard.
  • Page 5 ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to the instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.
  • Page 6 See Hardware Identifier Item * You may have extra parts with this model. P/N 21145507 02/04 PARTS LIST - (See Hardware Identifier) Qty. Part No. Description 914822 Top Pole Section 990062 Middle Pole Section 908812 Bottom Pole Section 202800 Ground Sleeve 202801 Ground Sleeve Cap 203279...
  • Page 7 HARDWARE IDENTIFIER (BOLTS & SCREWS) Item #23 (1) Item #8 (2) Item #27 (1) Item #16 (1) Item #12 (3) Item #24 (2) Item #31 (6) Item #36 (1) HARDWARE IDENTIFIER (NUTS & WASHERS) Item #14 (3) Item #9 (5) Item #37 (2) Item #35 (6) Item #28 (1)
  • Page 8 SECTION A: ASSEMBLE THE POLE This is what your system will look like when you’ve finished this section: HARDWARE USED IN THIS SECTION TOOLS REQUIRED FOR THIS SECTION (not actual size) (2) 1/2”, (2) 9/16"” AND (2) 3/4” Wrenches Item #8 AND/OR Item #16 Item #10...
  • Page 9 Mark pole sections with tape (not supplied) at indicated distances from ends as shown. MIDDLE Tape (Not Supplied) BOTTOM Ensure ground is level with playing surface, then dig pole hole. WARNING! CONTACT UTILITIES BEFORE DIGGING. Note Maximum distance from edge of hole to edge of playing surface 6”...
  • Page 10 Insert and secure bottom pole section (3) into ground sleeve (4) by tightening ground sleeve cap (5). NOTE: Flared end goes inside ground sleeve. P/N 21145507 02/04 Fill hole approximately 1/3 full with concrete (FIG. A). Insert ground sleeve assembly and center in hole (FIG. B). Fill hole completely with concrete (FIG.
  • Page 11 Tamp down concrete to release air pockets and build drainage hill. Level pole section in all directions several times while concrete is curing. 1" (2.54 cm) WAIT A MINIMUM OF 24 HOURS BEFORE GOING ON TO NEXT STEP. CONCRETE MUST CURE. After concrete has cured, remove bottom pole section from ground sleeve (4).
  • Page 12 Install ground sleeve cap (5) onto bottom pole section (1). Stack and bounce bottom (3) and middle (2) pole sections together. Bounce pole sections together until middle section no longer moves toward taped reference mark on bottom pole. WOOD SCRAP (NOT SUPPLIED) Install pole mount bracket (7), bracket reinforcement (44) with carriage bolts...
  • Page 13 Attach spacers (10, 11) to pole mount bracket (7) with bolts (12), washers (13), and nuts (14) as shown. IMPORTANT! Tighten until washers (13) no longer move. Assemble lanyard (17) to locking pin (18) as shown in FIG. A. Attach covers (15) onto pole mount bracket (7) with carriage bolt (16) and nut (9) as shown.
  • Page 14 Apply logo and height indicator labels (19) to adjustment rod (20) as shown. Attach handle parts (21, 22) to adjustment rod with screw (23), carriage bolt (24), and flange nut (9) as shown. NOTE: Holes in adjustment rod allow for either rear access or side access. IMPORTANT!: Indicator labels should be applied as close to...
  • Page 15 SECTION B: ASSEMBLE THE BACKBOARD This is what your system will look like when you’ve finished this section: NOTE: ASSEMBLY WILL VARY DUE TO BACKBOARD STYLE. TOOLS REQUIRED FOR THIS SECTION (2) 1/2", (2) 9/16"” AND (2) 3/4” Wrenches AND/OR (2) Socket Wrenches and Sockets 1/2”...
  • Page 16 Use the following assembly instructions if you have a 44” molded plastic backboard (Rectangle or Fan) THIS BACKBOARD AND GOAL ARE NOT DESIGNED TO CAUTION: SUPPORT A PLAYER HANGING FROM THE GOAL OR NET. BODILY INJURY AND / OR PROPERTY DAMAGE. FAILURE TO OBSERVE THIS CAUTION MAY CAUSE Assemble elevator tubes (30) as shown.
  • Page 17 Use the following assembly instructions if you have a CAUTION: THIS BACKBOARD AND GOAL ARE NOT DESIGNED TO SUPPORT A PLAYER HANGING FROM THE GOAL OR NET. FAILURE TO OBSERVE THIS CAUTION MAY CAUSE BODILY INJURY AND / OR PROPERTY DAMAGE. Assemble elevator tubes (30) as shown.
  • Page 18 Use the following assembly instructions if you have a a 44” steel-framed acrylic backboard. Assemble backboard brackets to board as shown. Refer To Instructions Included With Backboard Hardware For Board Assembly. NOTE: Parts on this page are included in backboard mounting hardware.
  • Page 19 Refer To Instructions Included With Rim Hardware For Rim Assembly. NOTE: Peel protective film from surface of acrylic backboard prior to use. 02/04 P/N 21145507...
  • Page 20 Use the following assembly instructions if you have a 48” molded plastic-framed acrylic backboard. Assemble elevator tubes (30) as shown. Tighten completely. P/N 21145507 02/04 Install spacers (25), and springs (39) onto backboard brackets (26) with bolts (27, 36), washers (37) and lock-nuts (14, 28) as shown.
  • Page 21 SECTION C: ATTACH THE BACKBOARD/ELEVATOR TO POLE SYSTEM This is what your system will look like NOTE: when you’ve finished this section: BACKBOARD WILL VARY HARDWARE USED IN THIS SECTION TOOLS REQUIRED FOR THIS SECTION (not actual size) (2) 3/4” Wrenches AND/OR Item #33 (2) Socket Wrenches and Sockets...
  • Page 22 Support pole on sawhorse. Attach backboard assembly to top pole section (1). NOTE: Two people are required for this step, use caution, elevator assembly is heavy. WARNING TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE.
  • Page 23 Insert bolt (31) through left side short elevator tube (29), then stretch spring or springs (34) onto bolt (31). Insert bolt (31) through right side short elevator tube (29) and secure with nut (35). WARNING! USE EYE PROTECTION WHEN INSTALLING SPRINGS.
  • Page 24 Install clips. WARNING! USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS, OR WHEN ALL SMART CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. P/N 21145507 02/04 Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that second “arm”...
  • Page 25 NET INSTALLATION SIDE VIEW NETCLIP Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position. Net must be centered through clip. NETCLIP 02/04 P/N 21145507...
  • Page 26 IMPORTANT!: WAIT A MINIMUM OF 24 HOURS BEFORE GOING ON TO NEXT STEPS. CONCRETE MUST CURE. After concrete has cured, remove tape, install pole cap (40), fit pole assembly into sleeve (4). IMPORTANT! Position pole assembly so the elevator assembly is perpendicular with playing surface. IMPORTANT! The elevator holes MUST be parallel with playing surface.
  • Page 27 24A. Starting with nuts flush against bracket, secure rim and bracket to backboard. NOTE A: Do not use washers here on spring return style rim. WARNING TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE.
  • Page 28 A. While holding handle, remove pin (26). B. Move elevator up or down to desired height. C. Replace pin (26) full length to lock system at desired height. WARNING! DO NOT ALLOW CHILDREN TO ADJUST HEIGHT. P/N 21145507 02/04 Apply height adjustment label (38) to front of pole as shown.

Table of Contents

Save PDF