Page 1
Powered Personal Transportation GAS POWERBOARD Product Handbook MOBY 35/40 FOR THE BLADEZ GAS POWERBOARD Models: PB-SE802 PB-SE803 PB-SE1802 PB-SE1803 PLEASE BE SAFE WHEN RIDING ALWAYS WEAR A HELMET AND OBEY ALL LAWS! Page 1 of 18...
DO NOT RIDE IN WET/ICY CONDITIONS! Failure to follow these instruction or abuse will VOID YOUR WARRANTY! If you have any questions, please contact Bladez customer service (866) 325-2339 or visit us on the web at www.ebladez.com Page 2 of 18...
Page 3
IMPORTANT PLEASE READ THIS BEFORE USING THIS PRODUCT READ THIS FIRST! WARNING This product does not conform to Federal Motor Vehicle Standards and is not intended for operation on public streets, roads or highways. Serious injury can result from the unsafe operations of this product. Operator can minimize these risks by using certain safety equipment such as: safety helmet, goggles, gloves, elbow and kneepads and appropriate footwear.
Page 4
BLADEZ POWERBOARD BACK TO THE STORE! CONTACT US FIRST IF YOU HAVE ANY QUESTIONS OR NEED ASSISTANCE, PLEASE CALL BLADEZ, TOLL FREE AT: (866) EBLADEZ (866) 325-2339 MONDAY thru FRIDAY, 8am to 5pm PST or visit us on the web at: www.ebladez.com...
Page 5
Use only parts and accessories that are recommended by the manufacturer. If a situation arises that is not covered in the manual, proceed with caution and use good judgement. Contact your dealer or Bladez ( www.ebladez.com if you need further assistance...
TABLE OF CONTENTS TABLE OF CONTENTS....................6 GETTING TO KNOW YOUR BLADEZ POWER BOARD...........7 PACKAGE CONTENTS....................8 GETTING STARTED ....................8 FOLDING AND STORAGE ..................10 OPERATING PROCEDURES ...................11 MAINTENANCE......................12 RECOMMENDED TOOLS ....................12 CARBURETOR ADJUSTMENT.................... 12 BRAKING SYSTEM ......................13 TIRES AND WHEELS ......................14 ADJUSTING THE HEAD UNIT .....................
GETTING TO KNOW YOUR BLADEZ POWER BOARD Before operating your BLADEZ Power Board, please get acquainted with all of the features. Power Board Features Motor Features Throttle Lever 1. Recoil Starter Brake Lever 2. Gas Tank Disc Brake 3. Gas Cap 2-Stroke Engine 4.
PACKAGE CONTENTS Your Bladez MOBY comes with the following items in the box. Please locate all of the following: 1. The Bladez MOBY Power Board 2. Allen Wrench 3. Spark Plug wrench 4. Product Handbook GETTING STARTED Please read and understand these instruction and the OPERATING...
Page 9
7. Slowly open the GAS CAP, so that possible over-pressure disappears. 8. Clean the tank cap area to make sure that it is free from excess dirt and debris. * Make sure that no dirt falls into the gas tank. 9.
Riding 16. Makes sure that all of the exposed bolts and screws are tightened. 17. Raise the kickstand to its upright position. 18. Make sure the engine is running. 19. Put one foot on the deck of the MOBY. While pushing off with the other foot, gently depress the THROTTLE LEVER, on the right side of the handlebars.
OPERATING PROCEDURES Fuel WARNING! This is a two-stroke engine. Only run the engine on fuel, which is properly mixed with 2-cycle engine oil. Provide good ventilation when fueling or handling fuel. Always use gas with a minimum octane number of 90. Use 2-stroke engine oil only.
MAINTENANCE RECOMMENDED TOOLS To adjust and service the Bladez MOBY Power Board you will need the following tools: Allen Wrenches: 3 / 4 / 5 / 6mm. Wrenches: 10 / 13 / 16 mm Open and ring combination. Short reach Spark Plug Socket...
When the engine is idling, under no circumstances should your MOBY be moving. If the MOBY continues to move after idle speed adjustment, contact Bladez or your local Bladez service center. Cleaning the Air Filter It is a good idea to occasionally clean the air filter to insure optimum performance.
TIRES AND WHEELS The Bladez MOBY uses an identical rim and tires assembly on the front and rear wheels, which means that the tires can be rotated. The wheels are actually two wheel halves (split rim) bolted together to make it easier to remove and replace the tire and tube.
To adjust the head unit: 1. Rotate the handle bar as far right as it will go to expose the HEAD UNIT (Fig. 13). 2. Using a large adjustable wrench, gently turn the BEARING LOCK clockwise to tighten. * DO NOT OVER TIGHTEN OR IT WILL DAMAGE THE BEARINGS ADJUSTING THE BELTS The belts will come adjusted from the factory.
For additional questions, service instruction, further information and important phone numbers, please go to the Bladez website at www.ebladez.com. Thank You for purchasing a Bladez Power Board and please tell your friends about how much fun you had on the Bladez Power Board.
Page 17
Bladez, Inc. 20155 Ellipsse Foothill Ranch CA, 92610 (949) 206-0330 voice (949) 206-0350 fax Page 17 of 18...
Need help?
Do you have a question about the PB-SE802 and is the answer not in the manual?
Questions and answers