Go Spas GO 630 Owner's Manual
  1. Manuals
  2. Brands
  3. Go Spas Manuals
  4. Hot Tub
  5. GO 620
  6. Owner's manual

Go Spas GO 630 Owner's Manual

100 & 120 volt options
Hide thumbs
Table of Contents

Advertisement

Quick Links

HOT TUB OWNER'S MANUAL
MODELS:
GO 630/GO 620
,
(1202)
GO 631/GO 621/GO 631B-EX
(1203),
GO 632/GO 622
(1204)
Premium Leisure, LLC
th
6101 45
St. N.
St. Petersburg, FL 33714
727.573.9611
www.GoSpas.com
Part Number 1202
Revised 09/11

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GO 630 and is the answer not in the manual?

Questions and answers

Summary of Contents for Go Spas GO 630

  • Page 1 HOT TUB OWNER’S MANUAL MODELS: GO 630/GO 620 (1202) GO 631/GO 621/GO 631B-EX (1203), GO 632/GO 622 (1204) Premium Leisure, LLC 6101 45 St. N. St. Petersburg, FL 33714 727.573.9611 www.GoSpas.com Part Number 1202 Revised 09/11...
  • Page 2 Owner’s Information Dealer: Date Purchased: __________________________ Company: __________________________ Address: __________________________ Telephone: __________________________ Installer: Date Installed: __________________________ Company: __________________________ Address: __________________________ Telephone: __________________________ Hot Tub: Date Delivered: __________________________ Model: __________________________ Color: __________________________ Serial Number: __________________________ Your unique hot tub serial number is located on a data plate outside the cabinet at ground level directly below the topside control panel.

  • Page 3: Table Of Contents

      Certificate of Verification  ..................52 Important: Go Spas is dedicated to offering you the best in customer satisfaction and service. Be sure to read, complete, sign, and send in the limited warranty card within 30 days of purchase to ensure you understand what you are entitled to in terms of service.

  • Page 4: Introduction

    I n t r o d u c t i o n ™ Your choice of a Go Spas hot tub indicates that you are devoted to excellence. The management and staff appreciate your patronage and takes pride in the tradition of quality hot tubs that our company represents.

  • Page 5: Important Safety Information

    I m p o r t a n t S a f e t y I n f o r m a t i o n IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Your physiological response to hot water depends on subjective factors such as age, health, pregnant women, temperature sensitivities, chemical sensitivities, and medical history.
  • Page 6 tub or when you are wet, unless such appliances are built-in by the manufacturer. Warnings TO REDUCE THE RISK OF INJURY:  The water in a spa should never exceed 40˚C (104˚F). Water temperatures between 38˚C (100˚F) and 40˚C (104˚F) are considered safe for a healthy adult. Lower water temperatures are recommended for young children and when spa use exceeds 10 minutes.
  • Page 7 Warning Sign Warning Sign Must Be Posted – The red WARNING sign like the one shown is packed with your new hot tub. This sign must be posted in a prominent place in close proximity to the hot tub installation site immediately upon completion of hot tub installation.

  • Page 8: Save These Instructions

    SAVE THESE INSTRUCTIONS Basic Safety Guidelines Your hot tub is meant to be enjoyable, healthful, and relaxing. Below are some basic safety guidelines to follow every time you use your tub.  Always check the temperature of your hot tub before entering.

  • Page 9: Site Selection And Installation

    S i t e S e l e c t i o n a n d I n s t a l l a t i o n Proper planning is an important consideration when installing your new tub. Site selection is a critical step and requires serious thought. Planning ahead makes the installation process easier.
  • Page 10 The following dimensions can be used to determine the proper location of submerged conduits in concrete slab installations. All dimensions are made from the outside of the hot tub’s frame with the access panels removed. The topside control panel is shown at bottom of diagram for reference. Figure 2 –...

  • Page 11: Electrical Specification And Wiring Diagrams

    Pack 6-3 plus ground (up to 130’) 1202, 1203, 1204 4-3 plus ground (up to 230’) VS500Z (GO 630) (GO 631) (GO 632) 2-3 plus ground (up to 360’) 12-2 plus ground (up to 130’) ‡ 1202C, 1203C, 1204C 10-2 plus ground (up to 230’)
  • Page 12 WARNING: Test the GFCI (or RCD) before each use. Our hot tubs are certified by Intertek Testing, SNAa Ltd. Ontario, Canada to CSA-C22.2 No. 218.1-M89 and ANSI/UL 1563 standards. Parts with extra low voltage not exceeding 12v must be inaccessible to a person in the hot tub.
  • Page 13 Figure 5 – U.S. and Canada Wiring Diagram See wire size chart on page 9. Page 11 For HELP, call 727.573.9611...
  • Page 14 Figure 6 – European 1x32A Wiring Diagram All wiring is 3x4 mm , solid copper See wire size chart on page 9. Note: Make sure that the DIP switches in the hot tub Pack are properly set for 50Hz operation and Jumper A is in place. Page 12 For HELP, call 727.573.9611...
  • Page 15 Figure 7 – European 2x16A Wiring Diagram All wiring is 5x1.5 mm , solid copper See wire size chart on page 9. Note: Make sure that the DIP switches in the hot tub Pack are properly set for 50Hz operation and Jumper A is removed. Page 13 For HELP, call 727.573.9611...
  • Page 16 Page 14 For HELP, call 727.573.9611...
  • Page 17 Figure 9 – Board Diagram and Panel Positions for all 240V single phase domestic models. A10 switch is OFF. A10 switch must be ON for 120V domestic version). Page 15 For HELP, call 727.573.9611...
  • Page 18 Figure 12 – VS510SZ Board Diagram for All EXPORT Models Page 16 For HELP, call 727.573.9611...
  • Page 19 Figure 13 – Board Diagram and Panel Positions for all EXPORT Models Figure 14 – Panel Button Positions for export models. Page 17 For HELP, call 727.573.9611...

  • Page 20: Startup

    S t a r t u p Important – Read these step-by-step startup procedures before starting your hot tub. Failure to follow any of these steps listed may result in damage to the equipment and may void your warranty. Note: If you are unsure of any of the above startup procedures, please call our customer care center, at 727.573.9611.
  • Page 21 Before Adding Water Before adding water, go through these simple steps now to prevent common issues when setting up your hot tub for the first time. Verify that the following have all been rechecked. Turn off all power to the hot tub at the main breaker panel.
  • Page 22 Filling Your Hot Tub Now it's time to fill your hot tub with water. Do not turn on the electricity yet until the hot tub is completely filled. To properly fill your tub: Make sure that the filters (in the filtration canister) are gently screwed into place.
  • Page 23 Interrupter (GFCI) breaker by pushing the small button. This should automatically trip the hot tub's circuit breaker. DANGER: If this breaker does not trip, immediately call your electrician. Do not use your hot tub! Only if pushing this button successfully trips this circuit breaker should you reset this breaker and proceed to the next step.

  • Page 24: Water Balancing

    W a t e r B a l a n c i n g Note: Perform water balancing weekly and whenever your water is changed (or when the hot tub is first filled) to assure proper water condition. Once your hot tub reaches 95ºF, use our Bromine Test Strips (not included) and add the necessary chemicals (not included) to stabilize your water chemistry.

  • Page 25: Topside Control

    T o p s i d e C o n t r o l Programming Instructions Domestic Figure 19 –Topside Control Panel (MVP 260 Domestic) Lamps  When the Jets LED is on steady, the system is in a filtration cycle. ...
  • Page 26 Programming Instructions Export Figure 20 – Topside Callouts for VL600S Controls Initial Start Up When your hot tub is first actuated, it will go into Priming mode, indicated by “Pr.” The priming mode will last for less than five minutes. Press “WARM” or “COOL” to skip Priming Mode and then the hot tub will begin to heat and maintain the temperature in “Standard Mode.”...
  • Page 27 mode). When the low speed turns on automatically, it cannot be deactivated from the panel, however the high speed may be activated. Aux Button Press the “AUX” button once to turn on Blower (if equipped). Press it a second time to turn off Blower. If left running, Blower automatically will turn off after 15 minutes.
  • Page 28 Programming Summary Figure 21 – VL600S Programming Summary NOTE FOR THE MVP 260 TOPSIDE CONTROLS:  Follow the above steps to set the filter cycle and water temperature.  To set the operating modes domestically with the MVP 260 controls, follow the steps above except instead of pressing “Mode”...

  • Page 29: Cover

    C o v e r Place the insulated cover on your hot tub. Keeping the cover in place anytime the hot tub is not in use reduces the heating time and minimizes operating costs. The time required for initial heat-up varies depending on the starting water temperature, ambient temperature, and the capacity of your hot tub.

  • Page 30: Frequently Asked Questions

    Who are the service companies in my area? Go Spas contracts with several service companies in your area to ensure the best possible response time. Our customers are guaranteed to receive service response priority. If you encounter a matter that can’t be easily resolved over the phone, a local technician can be dispatched to your home.
  • Page 31 What happens when my warranty expires? Go Spas will continue to provide service for your hot tub after your warranty has expired via our customer care center at 727.573.9611. Where can I get more Chemicals or other accessories? Visit www.hottubparts.com or call 877.530.PARTS.
  • Page 32 What is the shell made of? We use Lucite® Cast Acrylic with Microban® Antimicrobial Protection for most of our hot tub shells. Microban antimicrobial product protection is built-in to Lucite acrylic during the manufacturing process to help prevent the growth of stain causing bacteria on the surface of the hot tub.

  • Page 33: Troubleshooting

    T r o u b l e s h o o t i n g If a problem arises, you can check this list for a quick solution. If this does not resolve your problem, please call our customer care center, at 727.573.9611. Additional information is also available at www.PremiumLeisure.com.
  • Page 34 PROBLEM CAUSE SOLUTION not flow Closed jets Open all jets by turning counterclockwise ACV open Close air control valves Water too hot High set Turn down set temperature on topside temperature control panel High ambient Remove the cover temperature Water will not Thermostat is Check and reset to desired temperature heat...
  • Page 35 MESSAGE MEANING ACTION REQUIRED Sensor B is not Check the sensor "B" plug connection to working correctly. circuit board. The problem may appear Hot tub is shut temporarily in an overheat situation and down. disappear when the heater cools. If the problem persists, contact service.

  • Page 36: Maintenance And Care

    M a i n t e n a n c e a n d C a r e Important – The warranty on your hot tub and equipment depends on proper sanitation (see page 36). In addition, the following maintenance procedures must be followed periodically.
  • Page 37 Draining and Refilling Figure 25 - Drain Operation Turn off the GFCI breaker. Remove hot tub cover and allow water to cool down. Select a safe, suitable drainage area capable of safely assimilating 300 plus gallons of water that may contain unsanitary contaminants and chemical residue that could cause harm to plants or grass.
  • Page 38 Shutdown / Winterizing Your Go Spas hot tub is designed to operate year round. If you plan to leave your hot tub unused for long periods of time in severely cold weather, you should winterize your hot tub to avoid accidental freezing due to a power or equipment failure.
  • Page 39 Water Management Our chemical water purification system is a perfect match for your hot tub. Depending on usage, the water in your hot tub should be changed every 1-3 months. Upon each change of water it is a good practice to wipe down the hot tub.

  • Page 40: Specifications

    S p e c i f i c a t i o n s GO 630 (Model 1202) * Specifications are subject to change without notice. Spa Model     1202/GO630     Spa Dimension  84"x 72"x34"  Dry Weight (LBS/KG)  700/317  Number Of Seats  5  Filled Weight (LBS/KG)  3012/1366  Electrical Rating  Water Jets ...
  • Page 41 Call-Outs 1202/GO630 Label Part# Description Qty. 212-1509DSGSSSM Jet, Cluster storm, Directional 2" (SS); 218-5150 Compensator Ring 2" 212-1550G Body, Jet 2" 212-1529DSGSSSM Jet, Cluster, Pulsator 2" (SS); 218-5150 Compensator Ring 2"; 212-1550G Body, Jet 2", Gasket, Nut 212-7929DSGSSSM Jet, Mini storm, Directional 3" (SS); 718-6960 Compensator Ring 3";...
  • Page 42 GO 620 (Model 1202C) * Specifications are subject to change without notice. Spa Model     1202C/GO620     Spa Dimension  84"x 72"x34"  Dry Weight (LBS/KG)  700/317  Number Of Seats  5  Filled Weight (LBS/KG)  3012/1366  Electrical Rating  Water Jets  20  (VAC/AMP/HZ)  115/230/16/40/60  Water Capacity (USG/L)  277/1049  GFCI (AMP)  20/50  Page 40 For HELP, call 727.573.9611...
  • Page 43 Call-Outs 1202C/GO620 Label Part# Description Qty. 212-1549DSGSM Jet, Cluster storm, Directional 2" (Gr); 218-5150 Compensator Ring 2" 212-1550G Body, Jet 2" 212-1529DSGSM Jet, Cluster, Pulsator 2" (Gr); 218-5150 Compensator Ring 2"; 212-1550G Body, Jet 2", Gasket, Nut 212-7929DSGSM Jet, Mini storm, Directional 3" (Gr); 718-6960 Compensator Ring 3";...
  • Page 44 GO 631 (Model 1203) * Specifications are subject to change without notice Spa Model  1203/GO631  Spa Dimension  84"x 66"x34"  Number Of Seats  3  Water Jets  31  Air Jets  0  Water Capacity (USG/L)  235/890  Dry Weight (LBS/KG)  500/227  Filled Weight (LBS/KG)  2462/1117  Electrical Rating  (VAC/AMP/HZ)  230/40/60  Page 42 For HELP, call 727.573.9611...
  • Page 45 GFCI (AMP)  50  Call-Outs 1203/GO631 Label Part# Description Qty. 212-1509DSGSSSM Jet, Cluster storm, Directional 2" (SS); 218-5150 Compensator Ring 2" 212-1550G Body, Jet 2" 212-1529DSGSSSM Jet, Cluster, Pulsator 2" (SS); 218-5150 Compensator Ring 2"; 212-1550G Body, Jet 2", Gasket, Nut 212-7929DSGSSSM Jet, Mini storm, Directional 3"...
  • Page 46 GO 621/1203C * Specifications are subject to change without notice. Spa Model  1203C/GO621  Spa Dimension  84"x 66"x34"  Number Of Seats  3  Water Jets  21  Water Capacity (USG/L)  235/890  Dry Weight (LBS/KG)  485/220  Filled Weight (LBS/KG)  2447/1110  Electrical Rating (VAC/AMP/HZ)  115/230/16/40/60  GFCI (AMP)  20/50  Page 44 For HELP, call 727.573.9611...
  • Page 47 Call-Outs 1203C/GO621 Label Part# Description Qty. 212-1509DSGSSSM Jet, Cluster storm, Directional 2" (SS); 218-5150 Compensator Ring 2" 212-1550G Body, Jet 2" 212-1529DSGSSSM Jet, Cluster, Pulsator 2" (SS); 218-5150 Compensator Ring 2"; 212-1550G Body, Jet 2", Gasket, Nut 212-7929DSGSSSM Jet, Mini storm, Directional 3" (SS); 718-6960 Compensator Ring 3";...
  • Page 48 GO 631B-EX/1203B-EX * Specifications are subject to change without notice Spa Model  1203B‐EX/GO631B‐EX  Spa Dimension  84"x 66"x34"  Number Of Seats  3  Water Jets  31  Air Jets  10  Water Capacity (USG/L)  235/890  Dry Weight (LBS/KG)  525/238  Filled Weight (LBS/KG)  2487/1128  Electrical Rating (VAC/AMP/HZ)  220‐230/1x32,2x16/50  RCD (AMP)  IEE Req.  Page 46 For HELP, call 727.573.9611...
  • Page 49 Call-Outs 1203B-EX/631B-EX Label Part# Description Qty. 212-1509DSGSSSM Jet, Cluster storm, Directional 2" (SS); 218-5150 Compensator Ring 2" 212-1550G Body, Jet 2" 212-1529DSGSSSM Jet, Cluster, Pulsator 2" (SS); 218-5150 Compensator Ring 2"; 212-1550G Body, Jet 2", Gasket, Nut 212-7929DSGSSSM Jet, Mini storm, Directional 3" (SS); 718-6960 Compensator Ring 3";...
  • Page 50 GO 632 (Model 1204) Specifications are subject to change without notice. Spa Model  1204/GO632  84"x  Spa Dimension  66"x34"  Dry Weight (LBS/KG)  500/227  Number Of Seats  5  Filled Weight (LBS/KG)  2586/1173  Water Jets  32  Electrical Rating (VAC/AMP/HZ)  230/40/60  Water Capacity (USG/L)  250/946  GFCI (AMP)  50  Page 48 For HELP, call 727.573.9611...
  • Page 51 Call-Outs 1204/GO632 Label Part# Description Qty. 212-1509DSGSSSM Jet, Cluster storm, Directional 2" (SS); 218-5150 Compensator Ring 2" 212-1550G Body, Jet 2" 212-1529DSGSSSM Jet, Cluster, Pulsator 2" (SS); 218-5150 Compensator Ring 2"; 212-1550G Body, Jet 2", Gasket, Nut 212-7929DSGSSSM Jet, Mini storm, Directional 3" (SS); 718-6960 Compensator Ring 3";...
  • Page 52 GO 622 (Model 1204C) Specifications are subject to change without notice. Spa Model  1204C/GO622  84"x  Spa Dimension  66"x34"  Dry Weight (LBS/KG)  500/227  Number Of Seats  5  Filled Weight (LBS/KG)  2586/1173  Electrical Rating  Water Jets  22  (VAC/AMP/HZ)  115/230/16/40/60  Water Capacity (USG/L)  250/946  GFCI (AMP)  20/50  Page 50 For HELP, call 727.573.9611...
  • Page 53 Call-Outs 1204C/622C Labe Part# Description Qty. 212- Jet, Cluster storm, Directional 2" (SS); 1509DSGSSSM Compensator Ring 2" 218-5150 Body, Jet 2" 212-1550G 212- Jet, Cluster, Pulsator 2" (SS); 1529DSGSSSM Compensator Ring 2"; 218-5150 Body, Jet 2", Gasket, Nut 212-1550G 212- Jet, Mini storm, Directional 3"...

  • Page 54: Certificate Of Verification

    Page 52 For HELP, call 727.573.9611...
  • Page 55 N o t e s Page 53 For HELP, call 727.573.9611...
  • Page 56 Page 54 For HELP, call 727.573.9611...
  • Page 57 W a r r a n t y Lifetime Spa Structural Warranty  Premium Leisure LLC warrants the Go Spas shell structure against the loss of water through the fiberglass laminate of the shell  caused by defects in materials and workmanship for as long as the original purchaser owns the spa.  Contact manufacturer if you  have any questions concerning warranty issues.  Five (5) Year – Spa Surface Warranty  Premium Leisure LLC Warrants the Go Spas interior acrylic spa surface against blisters, cracks, or delaminating resulting from a  defect in the acrylic surface material for a period of five (5) years from the date of purchase, based on the following formula:   Suggested retail price divided by months covered (60), multiplied by months owned plus shipping = replacement cost.     Lifetime Manifold Plumbing Parts Warranty  Premium Leisure LLC warrants the Go Spas plumbing manifolds, fittings, and parts to be free of defects in materials or workmanship  for as long as the original purchaser owns the spa.  One (1) Year – Limited Spa Equipment Warranty  Premium Leisure LLC warrants the Go Spas electrical equipment and components to be free of defects in materials and workmanship  for a period of One (1) years on major spa components (electrical system, spa controls, motors) and one (1) years authorized field  service on these items.  Ninety (90) day (Parts ONLY) Limited Warranty on all optional accessory items (optional cabinets, fixtures,  trim kits, skirts, CD & MP3 players, all other music and video devices, ozone, waterfall assembly, LED lighting, etc).  All perishable,  cosmetic or owner serviceable items, spa cover, light bulb, light lenses, fuses, headrests, cabinet, filters, cover‐lift, spa drain, jet  inserts, etc are warranted to be free of defects in materials and workmanship at the time of delivery.  These items may be covered  by a manufacturer’s warranty.  Premium Leisure LLC may serve as an agent in presenting claims under the manufacturers’  warranties, but disclaims any liability there under.  In the event Premium Leisure LLC provides parts to replace an alleged defective  part under warranty owner will be billed for the cost thereof and credited, minus freight, upon both the defective part being  returned to Premium Leisure LLC and the manufacturer of said part accepting warranty claim.    Warranty Performance  In the event of a suspected defect, under the terms of this Limited Warranty, notify manufacturer.  Use all reasonable means to  protect the spa from further damage.  A service representative will provide the technical labor only, to affect the repair subject to  the terms and conditions contained in this Limited Warranty.  The service representative may assess reasonable travel charges.   Visits to simply diagnose, troubleshoot, or inspect problems are not covered under this Limited Warranty.  If we determine that  repairs are not feasible due to functional defect, we reserve the right to provide a replacement part or spa in lieu of repair.  We will  replace with a part of value equal to the original purchase.  In such event, owner is responsible for expenses including removal,  shipping, and re‐installation of the existing or replacement hot tub.  The replacement spa or part will carry the balance of the  original spa’s warranty, if any.  Either party’s waiver of any breach or failure to enforce any of the terms or conditions of the  warranty shall not in any way affect, limit or waive such party’s right at any time to enforce strict compliance with every term and  condition thereof. ...
  • Page 58 6101 45 St. N. St. Petersburg, FL 33714 727.573.9611 www.GoSpas.com...

Table of Contents

Save PDF