Lifetime 60028 Owner's Manual
  1. Manuals
  2. Brands
  3. Lifetime Manuals
  4. Outdoor Storage
  5. 60028
  6. Owner's manual

Lifetime 60028 Owner's Manual

Hide thumbs Also See for 60028:

Advertisement

Table of Contents

See also: Manual
OUTDOOR STORAGE
MODEL N° 60028
OWNER'S MANUAL
Keep this Identification Number in case you must contact our Customer Service Department.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 60028 and is the answer not in the manual?

Questions and answers

Related Manuals for Lifetime 60028

Summary of Contents for Lifetime 60028

  • Page 1 OUTDOOR STORAGE MODEL N° 60028 OWNER’S MANUAL Keep this Identification Number in case you must contact our Customer Service Department.
  • Page 2 REGISTER YOUR LIFETIME PRODUCT TODAY! There are benefi ts to registering your Lifetime product. With our new online product registration form, it’s fast and easy! Register with us at www.lifetime.com and enjoy these great benefi ts: LIFETIME’S PROMISE TO YOU: Maintaining your privacy is our long-standing policy at Lifetime.
  • Page 3 BEFORE BEGINNING ASSEMBLY *Two adults required to complete assembly* *Two adults required to complete assembly* Only adults should set up the product. Do not allow children in the set-up area until assembly is complete. TOOLS AND PARTS REQUIRED FOR THIS ASSEMBLY Socket Wrench Rubber Mallet #2 Phillips...
  • Page 4 ASSEMBLY GUIDES Refer to the following areas throughout the instructions to assist in the assembly process: This area is located at the top, left-hand TOOLS AND HARDWARE REQUIRED FOR THIS PAGE corner of the page and indicates which tools and hardware are needed to complete the assembly steps on a page.
  • Page 5 PARTS & HARDWARE LIST MAIN COMPOSTER PARTS Description Description TUMBLER ASSEMBLY HARDWARE BLISTER PACK TUMBLER ASSEMBLY HARDWARE BAG COMPOSTER PARTS KIT CQV COMPOSTER HARDWARE BAG BASE ASSEMBLY HARDWARE BAG PARTS IDENTIFIER Main Composter Parts...
  • Page 6 PARTS IDENTIFIER Main Composter Parts Small Parts Kit [CQU] WARNING *BIJ...
  • Page 7 HARDWARE IDENTIFIER Base Assembly Hardware [CQW] Tumbler Assembly Hardware Blister Pack [CSF] Tumbler Assembly Hardware Bag [CQX]...
  • Page 8 BASE ASSEMBLY HARDWARE REQUIRED HARDWARE BAG REQUIRED: CQW BAG REQUIRED: CQU SMALL PARTS REQUIRED *BIJ PARTS REQUIRED TOOLS REQUIRED Safety Glasses Phillips Screwdriver...
  • Page 9 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS STEP BASE ASSEMBLY Inner Leg (COP) Outer Leg (COQ) Repeat this step for the second Leg. 2 ADULTS REQUIRED FOR THIS STEP A-Frames (BII) Composter Leg Assembly Repeat this step for the second Composter Leg Assembly.
  • Page 10 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Do not overtighten Screws.
  • Page 11 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Locking Pin Spring (BIN) Locking Pin Assembly (BIX) WARNING one of the Outer Housing Brackets...
  • Page 12 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Inner Housing Brackets (BIJ) Cap Nut (ADJ) Do not overtighten Nuts. Locking Pin WARNING...
  • Page 13 TUMBLER ASSEMBLY HARDWARE REQUIRED HARDWARE BAG & BLISTER PACK REQUIRED: CSF, CQX SMALL PARTS REQUIRED HARDWARE BAG REQUIRED: CQU...
  • Page 14 TUMBLER ASSEMBLY (CONT.) PARTS REQUIRED TOOLS REQUIRED Phillips Screwdriver Safety Glasses Rubber Mallet...
  • Page 15 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Panel (COF) Repeat this step for the second End Panel.
  • Page 16 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Rear Panel (COG) Repeat this step for Note: Do this step for only one of the Top/Bottom Panels (COE).
  • Page 17 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Panels (COE, COF, and COG) Blowhole Plug (BTK) BTK (x12)
  • Page 18 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE TUMBLER ASSEMBLY Mounting Plate (COJ) End Panel (COF) Repeat this step for the second End Panel (COF). Warning Sticker The extruded face of the Mounting Plate goes toward the End Panel.
  • Page 19 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Hinge Pivots (COK) to each Ensure the shoulder of the Hinge Pivot is in the recess of the plastic. Be careful to not overtighten the Nut. 1st End Panel Shoulder 2nd End Panel...
  • Page 20 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Sleeve (BIL) over a Grease Packet (AKH) Washers, Bushing, Sleeve, and Hex Bolt. Tear here...
  • Page 21 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Bolt, Washer, and Sleeve Assembly Be sure to insert a Black Plastic Spacer (BIM) between the End Panel and the Inner Housing Bracket of the A-Frame. Warning Sticker Bolt, Washer, and Sleeve Assembly...
  • Page 22 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE...
  • Page 23 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS PAGE 2 ADULTS REQUIRED FOR THIS STEP Orient the two End Panels to match the illustration below. Be sure to to align the two ventilation holes. 2.10 To help locate the correct Panel, the 3-letter ID (COG) is located on the inside of the Panel. Notches Ventilation Holes Locking Pin...
  • Page 24 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 2 ADULTS REQUIRED FOR THIS STEP 2.11 It’s OK if the Screws (ADW) spin freely at this point. Do not worry about stripping the plastic. Repeat this step for the other side of the Front Panel. Secure the Screws with ten (10) Plastic Nuts (BHK), but do not overtighten.
  • Page 25 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS PAGE 2.12 Ventilation Tube (BHQ) Ventilation Hole Locking Pin Ventilation Hole...
  • Page 26 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 2 ADULTS REQUIRED FOR THIS STEP 2.13 It’s OK if the Screws (ADW) spin freely at this point. Do not worry about stripping the plastic. Repeat this step for the other side of the Front Panel. Secure the Screws with ten (10) Plastic Nuts (BHK), but do not overtighten.
  • Page 27 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS PAGE Ventilation Tube Bushing (COH) Repeat this step for the other End Panel with the second Ventilation Tube Bushing. Placement Nub Placement Notch...
  • Page 28 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE . Repeat this 2.15 step for the second Ventilation Tube Bushing. Do not overtighten Screws.
  • Page 29 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 2.16 Repeat this step by flipping the Tumbler over and inserting one (1) Screw (ADX) through the holes on the opposite side of the Ventilation Tube. Do not overtighten Screws.
  • Page 30 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Hinge (COM) Screws (AWU) . Repeat this step for the other angled end Note: The 5/16” Flat Washers go between the Hinges and the Top/Bottom Panels.
  • Page 31 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS PAGE 2.18 (COE) Note: Use the Top/Bottom Panel (COE) you drilled through earlier.
  • Page 32 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 2.19 It’s OK if the Screws (ADW) spin freely at this point. Do not worry about stripping the plastic. Secure the Screws with eight (8) Plastic Nuts (BHK), but do not overtighten.
  • Page 33 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS PAGE Hook Straps (CON) 2.20 Notches...
  • Page 34 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 2.21 It’s OK if the (BHK), but do not overtighten.
  • Page 35 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS PAGE 2.22...
  • Page 36 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE Latches (COL) . It’s OK if the Screws (ADW) 2.23 spin freely at this point. Do not worry about stripping the plastic. Plastic Nuts (BHK) Do not overtighten Nuts. WARNING Note: Remove Lid when filling and emptying Tumbler. Note: It’s easier to turn the Screws (ADW) into the Plastic Nuts (BHK).
  • Page 37 LIFETIME COMPOST TUMBLERS 5-YEAR LIMITED FACTORY WARRANTY THE MANUFACTURER RESERVES THE RIGHT TO MAKE SUBSTITUTIONS TO WARRANTY CLAIMS IF PARTS ARE UNAVAILABLE OR OBSOLETE. PLEASE INCLUDE YOUR DATED SALES RECEIPT AND PHOTOGRAPHS OF DAMAGED PARTS. REGISTER YOUR PRODUCT FOR QUICKER CUSTOMER SERVICE.
  • Page 38 ® ENHANCE YOUR LIFETIME PURCHASE BY ADDING ACCESSORIES OR OTHER GREAT PRODUCTS To purchase accessories or other Lifetime Products, visit us at: www.lifetime.com Or call: 1-800-424-3865...

Table of Contents

Save PDF