Checking The Power Voltage - Sony Owner’s Guide Operational Manual

Example: Box cursor
Activating/deactivating the cursor
indication
The <CHAR/MARK MIX> page of the USER
(OPERATION) menu permits you to activate/deactivate
the cursor indication for each output.
<CHAR/MARK MIX> page
< C H A R / M A R K M I X >
V F 1 V F 2 M O N 1 V B S
C H A R : O N
M A R K E R : O N
C U R S O R : B O F F O F F O F F
Z E B R A : O F F O F F O F F O F F
V F G A T E M A R K E R : O F F
The CURSOR indication is deactivated for all the outputs
at the factory.
Menu item Function
VF1 Turn the cursor indication on the viewfinder
connected to the VF1 connector on/off.
VF2 Turn the cursor indication on the viewfinder
connected to the VF2 connector on/off.
MONITOR Turn the cursor indication on the monitors
connected to the MONITOR OUT
connectors on/off.
Setting the type and size of the cursor
For the outputs for which you activate the cursor indication
on the <CHAR/MARK MIX> page, select and adjust the
cursor to be displayed on the next <MARKER SETTING>
page.
<MARKER SETTING> page
< M A R K E R S E T T I N G > U 0 3
C E N T E R : O F F
S A F E T Y : O F F
E F F E C T I V E : O F F
A S P E C T : O F F
V A R I A B L E : - -
S A F E T Y : O F F
M A S K : O F F
C U R S O R :
B
P O S I H / V :
S I Z E W / H :
U 0 9
O N O N O N
O N O N O N
1
9 0 . 0 %
4 : 3
9 0 . 0 %
1 2
B O X
0 0
9 6 0 5 4 0
Menu item Function
CURSOR Select the type (BOX/CROSS) of the cursor
to be displayed.
POSI H/V Adjust the H (horizontal) position (–958 to
956) and the V (vertical) position (–538 to
536) of the center.
SIZE W/H Adjust the width (from the center to right or
left side) (16 to 1920) and the height (from
the center to top or bottom) (16 to 1080) of
the cursor.

3-6-8 Checking the Power Voltage

The settings of the NEAR END and END values to warn
of low voltage of a power supply can be checked on the
<BATTERY ALARM> page of the USER (OPERATION)
menu.
<BATTERY ALARM> page
< B A T T E R Y A L A R M >
D C I N ( 2 4 V )
T Y P E : A C A D P
B
N E A R E N D : ( 2 2 . 2 )
E N D : ( 2 1 . 6 )
D C I N ( 1 2 V )
T Y P E : A C A D P
N E A R E N D : ( 1 1 . 1 )
E N D : ( 1 0 . 8 )
Menu item Indication
DC IN (24V) Voltage of the 24-V power
TYPE Select the type of the 24-V power source.
NEAR END NEAR END value specified for the 24-V
power source of the selected type
END END value specified for the 24-V power
source of the selected type
DC IN (12V) Voltage of the 12-V power
TYPE Select the type of the 12-V power source.
NEAR END NEAR END value specified for the 12-V
power source of the selected type
END END value specified for the 12-V power
source of the selected type
This page is intended for display only. You can only switch
the type. If you want to change the values, use the <BATT
ALARM SET> page of the MAINTENANCE menu.
Viewing and Setting the Viewfinder Displays
U 1 5
2 4 . 2 V
1 2 . 8 V
47