1. Manuals
  2. Brands
  3. Movies 2 go Manuals
  4. Car Video System
  5. MMD11 A
  6. Installation manual

Movies 2 go MMD11 A Installation Manual

11" overhead lcd monitor with dvd player
Hide thumbs
Table of Contents

Advertisement

Quick Links

MMD11 A
11" OVERHEAD LCD MONITOR
WITH DVD PLAYER

Installation Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MMD11 A and is the answer not in the manual?

Questions and answers

Related Manuals for Movies 2 go MMD11 A

Summary of Contents for Movies 2 go MMD11 A

  • Page 1: Installation Guide

    MMD11 A 11" OVERHEAD LCD MONITOR WITH DVD PLAYER Installation Guide...

  • Page 2: Important Notice

    If this is the case, an optional relay box is available. The Audiovox part number is SIRSWB and it plugs into the 1/8" jack located next to the FM antenna on the side of the chassis.

  • Page 3: Materials Included In This Package

    MATERIALS INCLUDED IN THIS PACKAGE: 1) 11" TFT LCD Overhead Monitor With DVD Player – (1pc) 2) 12 Pin Power / Signal harness (P/N 112-3483) – (1pc) 3) 2 Pin Power Wire Harness with choke (P/N 112B3143) – (1pc) 4) 9 Pin ~ 3 RCA Jack Pigtail (P/N 112-3682) –...
  • Page 4 GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, Video Game, external amp, wireless headphones, VCP, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups. 3) Decide upon mounting locations of all components and method of mounting. 4) Prep the vehicle by removing any interior trim necessary to gain access to vehicle's wiring aswell as all areas where interconnecting wire harnesses will need to be located.

  • Page 5: Vehicle Preparation

    2) The mounting method and location will vary from vehicle to vehicle, so this manual will only focus on the installation of the MMD11 A and related console accessories. 3) Generally, the best location for the video monitor is where the vehicle's factory dome light is installed.

  • Page 6: Trim Ring Installation

    TRIM RING INSTALLATION: Note: This page only covers special installation considerations for thick trim ring installation. If the video monitor is to be installed in a vehicle with the thick trim ring, it may need to be trimmed to fit the contour of the vehicle Head liner. Note: The trim rings supplied with this unit are not designed to be trimmed.
  • Page 7 3. AUX – AUX *NOTE: If the optional relay box P/N SIRSWB is installed, it recommended that the antenna for the wireless FM Modulator be unplugged. See MMD11 A Wiring Diagram (Figure A) for antenna location. **NOTE: Extending the wireless antenna beyond its 12 inch length will cause the FM Modulator to exceed FCC limits for wireless transmission.
  • Page 8 MMD11 A Figure A...

  • Page 9: Connecting The Dome Lights

    CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply voltage to the interior lights to turn them on, negative switched systems apply ground to illuminate the bulbs.

  • Page 10: Troubleshooting

    Negative Switched Dome Lighting Red / black - Lamp on To 12 pin Black / red - Lamp common Purple / brown - Lamp Auto connector constant constant Factory Door ajar switch or Body Control computer Troubleshooting: SYMPTOM: REMEDY: No power at Video Monitor Verify +12 VDC on Red wire at 2 pin Power Harness behind video monitor.
  • Page 12 © 2009 Audiovox Electronics Corp. 150 Marcus Blvd. Hauppauge, NY 11788 128-8653...

Table of Contents