Specifications - Kubota WSM B1710 Workshop Manual

B1710 · B2110 · B2410 · B2710, WSM

SPECIFICATIONS

Model
PTO power
Maker
Model
Type
Number of cylinder
Bore and stroke
Total displacement
Engine power (ECE-R24)
Engine Engine power
(SAE gross)
Rated revolution
Maximum torque
Battery
Starting system
Lubricating system
Cooling system
Fuel
Fuel tank
Engine crankcase
(with filter)
Capacities Engine coolant
Transmission case
Front axle case
Front
Tires
Rear
Overall length (with 3P)
Overall width (min. tread)
Overall height
(with ROPS)
Overall height
(top of steering wheel)
Dimensions
Wheel base
Minimum ground
clearance
Front
Tread
Rear
Weight (with ROPS)
4WD with brake
Minimum turning
Bi-speed turn
radius
without brake
Clutch
Steering
Transmission
Travelling
system
Brake
Differential
Hydraulic control system
Pump capacity
Hydraulic
Three point hitch
system
At lift points
Max. lift
24 in. behind lift
force
points
PTO shaft
Rear
Revolution
PTO system
PTO shaft
Mid.
Revolution
Note : * Manufacture's estimate
The company reserves the right to change the specifications without notice.
B1710D
10.5 kW (14.3 PS)*
D905-D18
Indirect Injection. Vertical, water-cooled, 4-cycle diesel
72 × 73.6 mm
(2.83 × 2.90 in.)
3
898 cm (54.8 cu.in.)
12.1 kW (16.5 PS)
13.4 kW (18.0 HP)
51 N·m (37.6 ft-lbs)
Electric starting with cell starter 12 V, 1.4 kW
Forced lubrication by trochoidal pump
Pressurized radiator, forced circulation with water pump
Diesel fuel No. 2-D [above −10 °C (14 °F)], Diesel fuel No. 1 [below −10 °C (14 °F]
11.5 L (3.04 U.S.gals., 2.53 Imp.gals.)
3.7 L (3.9 U.S.qts., 3.3 Imp.qts.)
6-12B
8-16
2378 mm (93.6 in.)
990 mm (39.0 in.)
2246 mm (88.4 in.)
1283 mm (50.5 in.)
263 mm (10.4 in.)
740 to 910 mm
(29.1 to 35.8 in.)
658 kg (1451 lbs) 668 kg (1473 lbs)
–
Gear shift, 6 forward and 2 reverse
3P : 16.6 L/min. (4.4 U.S.gals./min., 3.7 Imp.gals./min.)
Power steering : 9.8 L/min. (2.6 U.S.gals./min., 2.2 Imp.gals./min.)
1 speed (540 rpm at 2600 engine rpm)
USA No. 5 (KUBOTA 10-tooth) involute spline
1 speed (2500 rpm at 2578 engine rpm)
7
B2110D B2110DB
12.7 kW (17.3 PS)*
KUBOTA
D1005-D18
3
76 × 73.6 mm (2.99 × 2.90 in.).
3
1001 cm (61.1 cu.in.)
14.0 kW (19.0 PS)
15.7 kW (21.0 HP)
43.3 r/s (2600 rpm)
59 N·m (43.5 ft-lbs)
12 V, RC : 79 min, CCA : 433 A
24 L (6.3 U.S.gals., 5.3 Imp.gals.)
3.0 L (3.2 U.S.qts., 2.6 Imp.qts.)
3.8 L (4.0 U.S.qts., 3.3 Imp.qts.)
4.5 L (4.8 U.S.qts., 4.0 Imp.qts.)
6-12
9.5-16
2405 mm (94.7 in.)
1040 mm (40.9 in.)
2268 mm (89.3 in.)
1305 mm (51.4 in.)
1500 mm (59.0 in.)
285 mm (11.2 in.)
830 mm (32.7 in.)
795 to 1015 mm (31.3 to 40.0 in.)
678 kg (1495 lbs)
2.1 m (6.9 feet)
2.1 m (6.9 feet)
Dry single plate
Integral type power steering
Wet disk type
Bevel gears
Position control
SAE Category I
750 kg (1655 lbs)
590 kg (1300 lbs)
SAE 1-3/8, 6 splines
SPECIFICATIONS
B2110HDB
12.0 kW (16.3 PS)*
12.5 L (3.30 U.S.gals.,
2.75 Imp.gals.)
694 kg (1530 lbs)
HST with 2 speeds
range gear shift
W10281170
KiSC issued 11, 2006 A