Franke F3D Frozen French Fry Dispenser Operating Manual
  1. Manuals
  2. Brands
  3. Franke Manuals
  4. Dispenser
  5. F3D Frozen French Fry Dispenser
  6. Operating manual
Franke F3D Frozen French Fry Dispenser Operating Manual

Franke F3D Frozen French Fry Dispenser Operating Manual

Frozen french fry dispenser
Hide thumbs

Advertisement

Table of Contents

3
F
D Frozen French Fry Dispenser
Operating Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the F3D Frozen French Fry Dispenser and is the answer not in the manual?

Questions and answers

Related Manuals for Franke F3D Frozen French Fry Dispenser

Summary of Contents for Franke F3D Frozen French Fry Dispenser

  • Page 1 D Frozen French Fry Dispenser Operating Manual...

  • Page 2: Table Of Contents

    Table of Contents Diagram: Key Components Page 3 Installation Page 4 Temperature Setting Page 6 Store-Opening Procedure Page 7 Reading the Control Panel Page 8 Dispensing MacFries Page 9 Store-Closing Procedure Page 11 Preventative Maintenance Page 13 Basic Troubleshooting: Freezer Page 14 Basic Troubleshooting: Dispenser Page 15...

  • Page 3: Diagram: Key Components

    Franke F3D Key Components Side Basket Storage Rack Hash Brown Rack Hopper Product Chute Doors Drum Product Chutes Rubber Deflector Dispense Area Main Drip Tray Side Basket Drip Tray Wire Basket Guide F3D Operating Manual Page 3...

  • Page 4: Installation

    Installation (Model F D 2.0 Dual Lane Model) 1 Uncrate the Unit § Using a large screwdriver and/or prybar, loosen and remove the wooden crate top. § Loosen and remove the crate front panel. Be careful not to scratch the dispenser’s cabinet with your tools.
  • Page 5 3 Position the Unit Usually, the F3D is positioned at the right-hand side of the fry station. The fry station line-up is as follows: Fry Bagging Station ß Fryers ß F3D Dispenser The fry basket storage rack must be mounted onto the side of the dispenser.

  • Page 6: Temperature Setting

    The F3D’s internal, adjustable thermostat maintains the correct MacFries storage temperature range (0° to –10° F.). This thermostat is properly calibrated and tested at the factory prior to shipment from Franke. A digital thermometer on the control panel displays the actual operating temperature.

  • Page 7: Store-Opening Procedure

    Start-Up Procedure 1 Dry All Parts Using a clean, sanitized towel, wipe down the freezer’s interior, chute doors, and the dispense area to remove any remaining moisture. Make sure all that all components that were removed for cleaning are completely dry before installing them. 2 Assemble Unit Install all removable components as follows: §...

  • Page 8: Reading The Control Panel

    Note! If not fully engaged, the hopper will not seat properly on the center hanger, and the freezer door will not close.) 3 Bring Freezer Down to Temperature Close the freezer door. Turn the main power switch on the control panel to “ON.”...

  • Page 9: Dispensing Macfries

    Dispensing MacFries 1 Remove Hash Brown Rack Once the freezer has reached 0° F or lower, open the freezer door and remove the optional hash brown storage rack from the top of the hoppers. (Tip: Use the rack to store bagged hash browns in the freezer during breakfast hours.) 2 Check the Hoppers Check that the hoppers are empty.
  • Page 10 Tip: Load size changes can only be made when the green “LOAD READY” light is on. 7 Dispense Fries Insert a fry basket all the way into the basket guide, with the bottom resting on the wire rack, and hold it steady. When the system is ready, indicated by the green “LOAD READY”...

  • Page 11: Store-Closing Procedure

    Operator Control Panel Store-Closing Procedure The F3D dispenser must be emptied, cleaned and defrosted every day. Tip: You can get a head start on cleaning by turning off one lane at some point after the dinner rush, but before closing. Disassemble and clean the parts for this lane while still dispensing fries from the other lane.
  • Page 12 § Remove rubber deflectors from hoppers. § Remove product chutes from chute door frames. § Remove freezer bottom from cabinet. § Remove side basket drip tray. § Remove wire basket racks from main drip tray. § Leave main drip tray in place for now, to collect dripping water while the freezer defrosts.

  • Page 13: Preventative Maintenance

    § Wipe down, sanitize and dry the freezer interior and the chute doors. Tip: The chute door frames are hinged. You can gently push them open to fully clean the chute doors and door frames. § Wipe down and sanitize the side basket hanger rack. §...

  • Page 14: Basic Troubleshooting: Freezer

    Verify that the condensing coil is free from debris by following the procedure outlined in Section 7 above. If these steps don’t resolve the problem, contact Franke Technical Support at (800) 537-2653; press 5 for Technical Services. Problem 2: The freezer will not run when turned on.

  • Page 15: Dispenser Troubleshooting

    Basic Troubleshooting: Dispenser PROBLEM POSSIBLE CAUSE WHAT TO DO Individual lanes will not Main power is off. Flip power switch to “ON” position. Toggle switch turn on. will illuminate. Allow 1-1/2 hours for cool-down before adding product. Machine is unplugged. Plug into 110 VAC outlet and turn on main power switch.
  • Page 16 Franke at (800) 537-2653; press 5 for Technical Services. Door sensor may have failed. If doors cannot be closed by hand, call Franke at (800) 537-2653; press 5 for Technical Services. Unable to change load Fill process has not completed.

  • Page 17: Replacement Parts List

    Replacement Parts Freezer Assembly ITEM QTY. PART NO. DESCRIPTION ROBOFREEZE ENC. FREEZER 800716 ASY, HOPPER 800699 ASY, DRIVE ROTOR 150129 MOUNT SENSOR 800697 BOTTOM FREEZER 800760 ASY, DOOR LIFT 800633 CHUTE PRODUCT 9562K48 SEAL RUBBER 1 1/2 DIA SHAFT 98410A133 RING RETAIN 1"...

  • Page 18: Hopper Assembly

    Hopper Assembly ITEM QTY. PART NO. DESCRIPTION 800680 HOPPER OPEN TOP 800649 ROTOR ROBOFREEZE 800531 BAFFLE Drum Motor Assembly ITEM QTY. PART NO. DESCRIPTION 800619 BLOCK MOTOR ROTOR 26-67-100-GM MOTOR GEAR REDUCTION 800620 DRIVE SHAFT ROTOR 92146A011 WSHR SPLIT #10 92196A252 SCR SHC 10-24 X 1 3/4 STST F3D Operating Manual...
  • Page 19 Lift Assembly ITEM QTY. PART NO. DESCRIPTION 800728 MOUNT DOOR MECH 800702 BRACKET OPTIC SENSOR 800742 ASY CABLE DOOR SENSE 800703 FLAG LIMIT 97245A555_3-12 PIN CLEVIS 3/16 X 1 1/2 800561 BLOCK DOOR ROTATION 94639A075 ROLLER CAM 800560 LINK DOOR ACTUATOR 800567 ARM CAM 26-67-100-GM...

  • Page 20: Specifications

    Specifications F3D Operating Manual Page 20...
  • Page 21 This document contains proprietary information, is the property of Franke Inc. and may not be reproduced or distributed without the express written permission of Franke Inc. Due to a continuous program of product development, Franke Inc. reserves the right to make changes in design and specifications without prior notice.

Table of Contents

Save PDF