Sole Fitness E35 Owner's Manual
  1. Manuals
  2. Brands
  3. Sole Fitness Manuals
  4. Elliptical Trainer
  5. E35
  6. Owner's manual

Sole Fitness E35 Owner's Manual

Elliptical
Hide thumbs Also See for E35:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual
Z100 / Z300
Z500
Z700
OWNER'S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR NEW ELLIPTICAL!

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the E35 and is the answer not in the manual?

Questions and answers

Related Manuals for Sole Fitness E35

Summary of Contents for Sole Fitness E35

  • Page 1 Z100 / Z300 Z500 Z700 OWNER’S MANUAL PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE OPERATING YOUR NEW ELLIPTICAL!

  • Page 2: Table Of Contents

    Operation of Your New Elliptical ...25 Maintenance Manufacturer s Limited Warranty ..35 ATTENTION- THIS ELLIPTICAL IS INTENDED FOR RESIDENTIAL USE ONLY AND IS WARRANTED FOR THAT APPLICATION. ANY OTHER APPLICATION VOIDS THIS WARRANTY IN ITS ENTIRETY. E25 / E35 Elliptical...

  • Page 3: Product Registration

    If you have any questions about your new product or questions about the warranty contact SOLE Fitness at 1-866-780-SOLE (7653). If you have a technical problem with your new elliptical contact SOLE technical service at 866-MYSOLE1 (697-6531) Please take a moment at this time to record the name of the dealer, their telephone number, and the date of purchase below to make any future, needed contact easy.

  • Page 4: Important Safety Instructions

    WARNING - Read all instructions before using this appliance. These three warnings paragraphs are for E35 owners: DANGER - To reduce the risk of electric shock disconnect your SOLE E35 elliptical from the electrical outlet prior to cleaning and/or service work.

  • Page 5: Important Electrical Information

    95% non-condensing (no water drops forming on surfaces). Grounding Instructions E35 only This product must be grounded. If the E35 s electrical system should malfunction or breakdown grounding provides a path of least resistance for electric current, reducing the risk of electric shock.

  • Page 6: Important Operation Instructions

    If you feel the buttons are not functioning properly with normal pressure, contact your SOLE dealer. POWER CONNECTOR LOCATED ON FRONT, LEFT HAND SIDE OF UNIT. Transportation The elliptical is equipped with two transport wheels which are engaged when rear of the Elliptical is lifted. E25 / E35 Elliptical...
  • Page 7 #106. 3/8" x 3/4" Split Washer (4pcs) Star Washer (4pcs) Hex Head Bolt (2pcs) #108. 5/16" x 2-1/4" #107. 3/8" x 1-1/2" Hex Head Bolt (4 pcs) Hex Head Bolt (2pcs) #101. 3/8" x 2-1/4" Hex Head Bolt (1pc) E25 / E35 Elliptical...
  • Page 8 Flat Washer (2 pcs) Nylon Nut (2 pcs) Step 4 #125. M6 x 10mm #126. Ø3.5 x 12mm #115. M5 x 15mm Phillips Head Screw (4 pcs) Sheet Metal Screw (2pcs) Phillips Head Screw (20 pcs) E25 / E35 Elliptical...
  • Page 9 Tools #161. Phillips Screw Driver (1 pc) #160. Short Screw Driver (1 pc) #162. 12/14 mm Wrench (1 pc) #159. 13/14mm Wrench (1pc) E25 / E35 Elliptical...
  • Page 10 4. Plug all of the connectors into the back of the console; Computer Cable (47), two Hand pulse Cables (52) and Resistance switch wires (55). Secure the Console (46) on the console mounting plate with four M5x10m/m Phillips Head Screws (117). E25 / E35 Elliptical...
  • Page 11 E25 / E35 Elliptical...
  • Page 12 4. Install the Front Handle Bar Covers (83 left, 85 right) and Rear Handle Bar Covers (84 left, 86 right) over the Handle Bar axle connections with the six 3.5x12m/m screws (126). E25 / E35 Elliptical...
  • Page 13 Handle Bar (10&11). The rod end should be on the inside of the Handle Bar bracket. Secure with a 5/16 x1-1/4 Hex Head bolt (109), 5/16 x 20mm Flat Washer (151) and 5/16 Nylon Nut (137) by using 13/14 mm Wrench (159) and 12/14 mm Wrench (162). E25 / E35 Elliptical...
  • Page 14 7. This step to be performed after the elliptical power is plugged in. Run the incline to position 8 and install the incline Rail Front Cover (89) up against the Middle Stabilizer tube with two M5x15mm Phillips Head Screws (115). E25 / E35 Elliptical...
  • Page 15 E25 / E35 Elliptical...
  • Page 16 #132. 3/8" x 3/4" Split Washer (4pcs) Star Washer (4pcs) Hex Head Bolt (2pcs) #135. 5/16" x 2-1/4" #133. 3/8" x 1-1/2" Hex Head Bolt (4 pcs) Hex Head Bolt (2pcs) #125. 3/8" x 2-1/4" Hex Head Bolt (1pc) E25 / E35 Elliptical...
  • Page 17 Hex Head Bolt (2 pcs) Flat Washer (2 pcs) Nylon Nut (2 pcs) Step 4 #145. M6 x 10m/m #142. Ø3.5x12m/m #139. M5 x 15m/m Phillips Head Screw (4 pcs) Sheet Metal Screw Phillips Head Screw (26pcs) (8pcs) E25 / E35 Elliptical...
  • Page 18 Tools #186. Phillips Screw Driver (1 pc) #185. Short Phillips Screw Driver (1 pc) #184. 13 / 14m/m Wrench (1 pc) #187. 12 / 14 m/m Wrench (1 pc) E25 / E35 Elliptical...
  • Page 19 Plug all of the connectors into the back of the console; Computer Cable (50), two Hand pulse Cables (57), Resistance switch wire (60) and Incline switch wire (61). Secure the mounting plate with four M5x10m/m Phillips Head Console (45) on the console Screws (144). E25 / E35 Elliptical...
  • Page 20 E25 / E35 Elliptical...
  • Page 21 (75) over the wire and snap it into the hole in the console mast. Install the Front Handle Bar Covers (105 left, 107 right) and Rear Handle Bar Covers (106 left, 108 right) over the Handle Bar axle connections and secure with the eight 3.5x10m/m Sheet Metal Screws (142). E25 / E35 Elliptical...
  • Page 22 Handle Bar (10&11). The rod end should be on the inside of the Handle Bar bracket. Secure both sides with a 5/16 x1-1/4 Hex Head Bolt (134), 5/16 x20mm Flat Washer (170) and 5/16 Nylon Nut (159) by using 13/14 mm Wrench (184) and 12/14 mm Wrench (187). E25 / E35 Elliptical...
  • Page 23 7. This step to be performed after the elliptical power is plugged in. Run the incline to position 8 and install the incline Rail front cover (113) up against the middle stabilizer tube with four M5x15mm Phillips Head Screws (139). E25 / E35 Elliptical...
  • Page 24 E25 / E35 Elliptical...
  • Page 25 There are 3 positions in total and at the top position, lifting the incline one more click will allow it to go back to the bottom. The E35 power incline is controlled by buttons on the console and swing arms and also automatically controlled during the built-in workout programs.

  • Page 26: Operation Of Your New Elliptical

    Operation of Your Elliptical Getting familiar with the control panel E25 Console E35 Console E25 / E35 Elliptical...

  • Page 27: Console Operation

    Calories, Level (work level from 1-20) and Pulse (heart rate in beats per minute). Pressing the Display key one more time will set the display the Incline level (E35 only) then scan mode where the displayed information will change every 4 seconds.
  • Page 28 Press each program key to scroll through the program selections. The profile for each program will be displayed in the dot matrix window. The E35 model will show the incline profile also when the Display key is pressed. Press the enter key to select a program and begin customizing the settings.

  • Page 29: Preset Programs

    (at the top of the hill). Adjust the level and then press enter. 6. *For E35 only: You can now choose to turn off the incline profile for this program. If you E25 / E35 Elliptical...
  • Page 30 You can also go back and modify your settings by pressing the Stop key to go back one level, or screen. 8. If you want to increase or decrease the workload or incline (E35 only) at any time during the program press the Up or Down keys.
  • Page 31 With all SOLE Heart Rate Control elliptical machines you may use the heart rate monitor feature without using the Heart Rate Control program. This function can be used during manual mode or during any of the nine different programs. The Heart Rate Control program automatically controls resistance at the pedals. E25 / E35 Elliptical...

  • Page 32: Rate Of Perceived Exertion

    If you are feeling tired and sluggish, it is because your body needs a break. In this condition, your pace will feel harder. Again, this will show up in your RPE and you will train at the proper level for that day. E25 / E35 Elliptical...
  • Page 33 90 degrees may de-tune the interference. (7) Loose treadmill console or bolts in the upright tube could also cause intermittent problems. (8) If you continue to experience problems contact your dealer. E25 / E35 Elliptical...
  • Page 34 Display key. When the program ends the message window will show a summary of your workout. The summary will be displayed for a short time then the console will return to the start-up display E25 / E35 Elliptical...

  • Page 35: Maintenance

    Incline calibration: If there is a problem with the incline, try running the calibration. Press the Incline up key and the Start key at the same time. Hold them down for 5 seconds and the Incline calibration will start and run automatically. If the problem persists contact service. E25 / E35 Elliptical...

  • Page 36: Manufacturer S Limited Warranty

    Submit all service requests including serial number, contact information and a brief description of the problem online at www.soletreadmills.com/technical.php?p=service. If you have any questions about your new product or questions about the warranty contact SOLE Fitness at 1-866-780-SOLE (7653). If you have a technical problem with your new elliptical contact SOLE technical service at 866-MYSOLE1 (697-6531).

This manual is also suitable for:

E25

Table of Contents