Related Manuals for Xterra SB2.5
Summary of Contents for Xterra SB2.5
- Page 1 SB2.5 RECUMBENT BIKE OWNER’S MANUAL PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE OPERATING YOUR NEW RECUMBENT BIKE...
-
Page 2: Table Of Contents
We appreciate your confidence in XTERRA Fitness and we will always remember that you are the reason that we are in business. Please complete and mail your registration card today and enjoy your new fitness bike. -
Page 3: Product Registration
Serial Number Register Your Purchase The self-addressed product registration card must be completed in full and returned to XTERRA Fitness. You can also go to www.xterrafitness.com/warrantyreg.html to register online. Power This product uses an external power supply. The power supply must be plugged into the power jack, located on the front of the unit near the stabilizer tube. -
Page 4: Important Safety Instructions
Failure to follow all guidelines may compromise the effectiveness of the exercise experience, expose yourself (and possibly others) to injury, and reduce the longevity of the equipment. SAVE THESE INSTRUCTIONS - THINK SAFETY! CAUTION!! Please be careful when unpacking the carton. SB2.5 Recumbent Bike... -
Page 5: Hardware Step
(1 pc) (11 pcs) #41. M5 x 12mm Phillips Head Screw (4 pcs) Hardware Step 2 #32. 5/16” x 3/4” #33. 5/16” #35. 5/16” Button Head Socket Flat Washer Split Washer Bolt (8 pcs) (4 pcs) (4 pc) SB2.5 Recumbent Bike... -
Page 6: Assembly Tools
Flat Washer (4 pcs) Bolt (6 pcs) (6 pcs) #63. 3/8” x 7T Nyloc Nut (6 pcs) Assembly Tools #69. 14/15mm Wrench #68. Combination M5 Allen Wrench & Phillips Head Screw Driver #92. M6 L Allen Wrench SB2.5 Recumbent Bike... -
Page 7: Sb2.5 Assembly Instructions
Console Mast Cover (80) down onto the plastic side covers. 4. Connect the cable (93) to the Console Assembly (47), then install the console onto the Console Mast (2) with four Phillips head screws (41). using the Phillips Head Screw Driver (68) to tighten SB2.5 Recumbent Bike... - Page 8 3. Attach the left and right handles (100, 101) to the Console Mast (2) with four Button Head Socket Bolts (32) using the Combination M5 Allen Wrench & Phillips Head Screw Driver (68). SB2.5 Recumbent Bike...
- Page 9 Seat Back Mounting Plate (54), then two Flat Washers (62), and two Nyloc Nuts (63).Tighten with the 14/15mm Wrench (69). 3. Connect the hand pulse connector (108 and 95) as shown in the inset picture below. SB2.5 Recumbent Bike...
-
Page 10: Operation Of Your Console
1 to 6. A score of 1 is an indication of a high level of fitness and a score of 6 indicates poor condition. MODE: Press to switch display from RPM to SPEED, ODO to DIST, WATT to CALORIES. SB2.5 Recumbent Bike... -
Page 11: Workout Selection
Using UP / DOWN KEY you may set the desired time value. Press ENTER KEY to input value. Flashing prompt will move to the next parameter. Continue use of UP / DOWN KEY. Press START / STOP to start workout. SB2.5 Recumbent Bike... - Page 12 Watt control program. Target Heart Rate will be based on Age. When heart rate ex- ± 10-99 ceeds Target Heart Rate, the number of heart rate will flash. Setting Paramters for Target ± Pulse 60-220 Heart Rate. SB2.5 Recumbent Bike...
-
Page 13: Program Operation
When any one of the workout parameters counts down to zero the console emits a beep sound and the workout stops automatically. Press START KEY to continue the workout to reach the unfinished workout goals set. SB2.5 Recumbent Bike... - Page 14 Pre-Set Programs (P2 - P13) SB2.5 Recumbent Bike...
- Page 15 Type 8 is from 40% to 44%. Type 9 is from 45% to 50%. BMR: Basal Metabolic Rate is the amount of daily energy expended at rest. BMI: Body Mass Index is a general body type based on height and weight. SB2.5 Recumbent Bike...
-
Page 16: User Program
Note: When any one of the workout parameters counts down to zero the console emits a beep sound and the workout stops automatically. Press START KEY to continue the workout to reach the unfinished workout goals set. SB2.5 Recumbent Bike... - Page 17 Normally the transmitter will be oriented so the XTERRA Fitness logo is right side up. 6. The antenna that picks up your heart rate is very sensitive. If there is an outside noise source, turning the whole machine 90 degrees may de-tune the interference.
-
Page 18: Heart Rate Control Program
60 seconds then it will decrease the resistance load 1 level every 10 seconds. When any one of the workout parameters counts down to zero the console emits a beep sound and the workout stops automatically. Press START KEY to continue the workout to reach the unfinished workout goals set. SB2.5 Recumbent Bike... -
Page 19: Manufacturer's Limited Warranty
Effective August 1, 2012 - BIKE LIMITED WARRANTY XTERRA Fitness Inc. warrants all its home use bike parts for a period of time listed below, from the date of retail sale, as determined by a sales receipt or in the absence of a sales receipt, eighteen (18) months from the original factory shipping date. XTERRA Fitness’s responsibilities include providing new or remanufactured parts, at XTERRA Fitness’s option, and technical support to our independent... - Page 20 3000 Nestle Road Jonesboro, AR 72401 - Phone:870-336-4286 - Fax:870-935-7611 www.xterrafitness.com ©2013 All RIghts Reserved. SB2.5r Owner’s Manual...
Need help?
Do you have a question about the SB2.5 and is the answer not in the manual?
Questions and answers
How to displace the seat to an aft position ?
The context does not provide specific instructions on how to move the Xterra SB2.5 seat to an aft position. However, it mentions that the seat is secured on a sliding seat carriage with Phillips head screws. To adjust the seat, you may need to loosen these screws, move the seat to the desired position, and then retighten them.
This answer is automatically generated