Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for iHome iBN19
Summary of Contents for iHome iBN19
- Page 1 Bluetooth alarm clock speaker with NFC and USB charging instruction manual...
- Page 2 Introduction Thank you for purchasing the iHome iBN19. This product is designed to provide high quality wireless sound for your iPad, iPhone, iPod or other Bluetooth audio device. Along with the included Quick Bluetooth Connection Guide this instruction booklet explains the basic operation and care of the unit.
- Page 3 FCC Information FCC ID: EMOIBN19 IC: 986B-IBN19 FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
-
Page 4: Table Of Contents
Table of Contents Meet Your iBN19......................1-3 The Display/Setting Up the Unit ..................4 Setting the Clock ......................5 Setting and Using the Alarm/Previewing Alarm ..............6 Snooze/Dimmer Button/Sleep and Nap Modes ..............7 Using Bluetooth: Pairing & Playing Your Device Using NFC ............8 Pairing Your Device Using Standard Bluetooth ................9... - Page 5 Included • iBN19 system • 100V-240V universal AC adaptor • 3.5mm audio cable audio cable iBN19 power adaptor...
-
Page 6: Meet Your Ibn19
Meet Your iBN19 NFC Antenna Volume Down Button Power Button Volume Up Button Minus/ Plus Settings Buttons Play/ Pause Button Nap/ Clock Set Button Alarm Button Mode Button Sleep Button Snooze/ Dimmer Button... - Page 7 Meet Your iBN19 Back USB Charging Port Pairing Button Aux-in Jack DC Jack Bottom Backup Battery Compartment (pull battery tab before use)
-
Page 8: The Display/Setting Up The Unit
Using the The Display Low Backup Time Display Battery Indicator PM/AM Indicators Alarm Active Indicator Bluetooth Pairing Indicator Aux-in Mode Indicator Snooze Mode Indicator Wake to Alarm Source Indicators: Bluetooth Audio Indicator Volume Indicator Tone, Bluetooth device Setting Up the Unit... -
Page 9: Setting The Clock
Using the Setting the Clock 1. Press and hold the Nap/Clock Set Button for 2 seconds until the clock display flashes and a beep sounds. 2. Press the – or + Buttons to adjust the clock to the current time (hold for rapid setting). -
Page 10: Setting And Using The Alarm/Previewing Alarm
Using the Setting and Using the Alarm Note: each step must be completed while display is flashing or step will time-out with any changes saved. 1. Press and hold the Alarm Button for 2 seconds until the time display and alarm icon flash. -
Page 11: Snooze/Dimmer Button/Sleep And Nap Modes
Using the Snooze/Dimmer Button 1. To program Snooze, press and hold the Snooze/Dimmer Button during normal operation (when no alarm is sounding). 2. Press the – or + Buttons to select the desired snooze time (between 01 and 29 minutes). -
Page 12: Using Bluetooth: Pairing & Playing Your Device Using Nfc
Bluetooth indicator icon will flash while the unit attempts to pair. “iHome iBN19” should appear on your device’s menu. Once paired with a device, the Bluetooth indicator on the display will stop flashing, then the Bluetooth icon will remain and a confirmation tone will sound and your music will play through the unit. -
Page 13: Pairing Your Device Using Standard Bluetooth
If “Not Paired”, “Not Connected” or similar message appears, select “iHome iBN19” on the device to connect it. If your device asks for a password, enter 1234 on the keyboard of your device. If no device is paired within 2 minutes, a tone will sound and the unit will revert to its previous mode. -
Page 14: Playing Audio Via Bluetooth/Playing Audio Via Aux-In
Using the Playing Audio Via Bluetooth 1. Press the Button to turn the unit ON. 2. Press and release the Mode Button as needed until the Bluetooth wave indicator icon appears on the display. Play Pause Button on the unit to play audio from your linked Bluetooth device. -
Page 15: Charging Devices Via Usb Port
Using the Charging Devices via USB Port 1. Connect the standard size end of a USB cable (not included) to the USB Port on back of the unit and connect the other end to the charging port on your device. -
Page 16: Replacing/Installing Backup Batteries
Using the Replacing and Installing Clock Backup Battery Note: The CR2450 lithium battery is included in the unit. Please pull out the battery pull tab before you use the unit. This model is equipped with a battery backup circuit that will maintain the time and alarm time settings in the event of a temporary power interruption (the display is NOT maintained). -
Page 17: Troubleshooting
Unit doesn’t respond (no power) • Check that all connections are correct and properly plugged in. • Make sure your device is properly paired with the iBN19. • Make sure the Power is ON. Unit doesn’t respond (locked up or frozen) •... -
Page 18: Consumer Product Safety Guide
Consumer Product Safety Guide IMPORTANT SAFETY INSTRUCTIONS When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. - Page 19 13. Servicing – The user should not attempt to service the unit beyond those methods described in the user’s operating instructions. Service methods not covered in the operating instructions should be referred to qualified service personnel. Questions? Visit www.ihome.com or call 1-800-288-2792 Toll Free...
-
Page 20: Warranty
Limited 1 Year Warranty iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI), warrants this product to be free from defects in workmanship and materials, under normal use and conditions, for a period of one (1) year from the date of original purchase.
Need help?
Do you have a question about the iBN19 and is the answer not in the manual?
Questions and answers