D-Link AC1200 Quick Manual

Wireless AC1200
Dual Band Gigabit Cloud Router
DIR-860L
Package Contents
DIR-860L Wireless AC1200 Dual Band Gigabit Cloud Router
Power Adapter
Ethernet Cable
Wi-Fi Configuration Card
Quick Install Guide
If any of the above items are missing, please contact your reseller.
Hardware Overview
3
4
1 5
2
6
7
8
9
A solid green light indicates a proper connection to the
1 Power LED power supply. The light will be solid orange during boot-up
and will blink green during the WPS process.
A solid light indicates a connection to the Internet port. If the
LED is orange, the connection is good but the router cannot
2 Internet LED connect to the Internet. If this LED is blinking orange, this
indicates that the "on demand" connection type is set and
the Internet connection is idle.
Connect a USB flash drive to share content throughout
3 USB Port
your network.
Press to start the WPS process. The Power LED will start to
4 WPS Button
blink.
Connect Ethernet devices such as computers, switches, and
5 LAN Ports (1-4)
game consoles.
Connect your broadband modem to this port using an
6 Internet Port
Ethernet cable.
7 Power Button Press to power the router on and off.
8 Power Port Connect the supplied power adapter.
Press and hold the reset button with a paper clip for six
9 Reset Button
seconds to reset the router to the factory default settings.
Minimum Requirements
Network Requirements:
• An Ethernet-based broadband modem
Web-based Configuration Requirements:
Computer with the following:
• Windows® or Mac OS® X operating system
• An installed Ethernet adapter or wireless adapter
Supported Browsers:
• Internet Explorer 7 or higher
• Safari 4 or higher
• Chrome
• Firefox
Make sure you have the latest version of Java installed. Visit www.java.com
to download the latest version.
mydlink Requirements:
• iPhone/iPad/iPod Touch (iOS 3.0 or higher)
• Android device (1.6 or higher)
• Web Browser Requirements:
• Internet Explorer 7 or higher
• Safari 5 or higher
• Chrome
• Firefox
Note: To learn more about mydlink, visit http://www.mydlink.com.
Before you Start
• Users with DSL providers - If you are using a PPPoE connection, you will need
your PPPoE user name and password. If you do not have this information, contact
your Internet provider. Do not proceed until you have this information.
• Users with Cable providers - Make sure you unplug the power to your modem.
In some cases, you may need to turn it off for up to 5 minutes.
• Advanced Users - If your ISP provided you with a modem/router combo, you will
need to set it to "bridge" mode so the DIR-860L router can work properly. Please
contact your ISP or refer to the user manual for your modem/router device.
Connect your Router
1
Unplug the power to your DSL or Cable modem.
Modem
2
Connect an Ethernet cable from the Internet port of the router to the
Ethernet port on your DSL or Cable modem.
Ethernet Cable
Ethernet Port
USB
WPS
1
2
LAN
3
4
Internet Port (yellow)
INTERNET
POWER
12V 2A
Modem
DIR-860L
3
Connect another Ethernet cable from the Ethernet port on your
computer to one of the LAN ports on the router.
USB
WPS
1
2
LAN
3
Computer
4 Ethernet Cable
INTERNET
POWER
12V 2A
DIR-860L
4
Plug the power back into your DSL or cable modem. Please wait about
one minute before continuing.
Computer
USB
WPS
1
2
LAN
3
4
INTERNET
POWER
12V 2A
Modem
DIR-860L
5
Plug the power adapter into your router and connect to an available
power outlet or surge protector. If the Power LED does not light up, press
the Power button on the back of the router.
Modem
Computer
USB
WPS
1
2
LAN
3
4
INTERNET
POWER
12V 2A
DIR-860L
6
After the router has powered up, verify that the Power (green) and Internet
(orange or green) LEDs are both lit then continue with the Configuration
section on the other side.