StarTech.com SV231DDVDUA Instruction Manual
2/4-port dvi and vga, usb kvm switch with audio and usb 2.0 hub
Hide thumbs
Also See for SV231DDVDUA:
- Instruction manual (14 pages) ,
- User manual (16 pages) ,
- Manual (16 pages)
Related Manuals for StarTech.com SV231DDVDUA
Summary of Contents for StarTech.com SV231DDVDUA
-
Page 1: Instruction Manual
SV231DDVDUA SV431DDVDUA Instruction Manual DVI VGA USB KVM Switch 2/4-Port DVI and VGA, USB KVM Switch with Audio and USB 2.0 Hub Manual Revision:10/05/2010 For the most up-to-date information, please visit www.startech.com... -
Page 2: Fcc Compliance Statement
StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. -
Page 3: Table Of Contents
Table of Contents Introduction ..............1 Packaging Contents..............1 System Requirements ..............1 Installation ............... 1 Hardware Installation ..............2 Driver Installation .................4 Operation ................. 4 Front Panel ..................4 Rear Panel (SV431DDVDUA only) ..........5 HotKey Control ................6 Alternative Hotkey Commands ............9 Change Leading Hotkey ..............10 Specifications .............. -
Page 4: Introduction
Introduction Packaging Contents • 1 x SV231DDVDUA or SV431DDVDUA KVM switch • 1 x Power Adapter • 1 x Instruction Manual System Requirements • DVI and VGA enabled computer system/video card • USB enabled computer system • DVI or VGA enabled display devices (e.g. monitor, projector, TV, etc.) •... -
Page 5: Hardware Installation
Hardware Installation Front View (SV431DDVDUA shown) Rear View (SV431DDVDUA shown) - Page 6 VGA connector(s) on the computer’s video card, to one of the KVM’s PC ports (ie. PC1). A dedicated video, USB and audio 4-in-1 KVM cable can be used (ie. StarTech.com ID: USBDVI4N1A6 (DVI) or USBVGA4N1A6 (VGA)). 3. Use a USB type A-B Cable to connect the KVM’s USB port (type B, square connector) for the PC port used in Step 2, and the USB port on the computer (type A, flat connector).
-
Page 7: Driver Installation
5. OPTIONAL: Connect any other USB peripherals you wish to share between the connected computers/devices to the extra USB Hub ports on the Console side. 6. Connect the external power adapter from a wall outlet to the power connector on the rear panel of the KVM switch. The Power LED should light up solid and/or the LED for the selected PC port. -
Page 8: Rear Panel (Sv431Ddvdua Only)
Auto Scan The KVM automatically scans through the powered-on computers in sequence on a fixed time interval (see Scan Time below). To activate Auto Scan, press down front panel push buttons “3” and “4” simultaneously. The port LED flashes during Auto Scan. Auto Scan is effective for powered-on computers only. -
Page 9: Hotkey Control
2. Press front panel push button “1” one or two times to adjust the signal equalization with one beep (normal) or two beeps (enhance) respectively. Press front panel push button “3” one or two times to adjust the video signal output current with one beep (normal) or two beeps (enhance) respectively. - Page 10 Auto Scan The KVM automatically scans through the powered-on computers in sequence on a fixed time interval (see Scan Time below). To start Auto Scan: Left <CTRL> + Left <CTRL> + <F1> To abort the Auto Scan mode, press the left <CTRL> key twice. NOTE: When Auto Scan detects any keyboard activity, it suspends the scanning until the activity stops;...
- Page 11 Audio Lock There are two options for Audio Lock: ON and OFF. When ON, audio selection follows computer selection. When OFF, audio selection stops following computer selection. It is useful if you want to listen to a particular computer’s audio signal while operating other computers. Left <CTRL>...
-
Page 12: Alternative Hotkey Commands
Alternative Hotkey Commands In addition to the Left <CTRL> + Left <CTRL> hotkeys, there are two alternative hotkey sequences available. 1. For the following operations, users may press <ScrollLock> twice instead of pressing left <CTRL> twice. To select a computer: <ScrollLock>... -
Page 13: Change Leading Hotkey
Change Leading Hotkey The default leading hotkey sequence involves pressing the left <CTRL> twice in succession (e.g. left <CTRL> + left <CTRL>). This can be changed to the right <CTRL> key instead, to avoid accidental activation due to using the left <CTRL> key for functions such as Copy/Paste. To change the leading hotkey sequence to Right <CTRL>: Left <CTRL>... -
Page 14: Specifications
Specifications SV231DDVDUA SV431DDVDUA Number of Ports 1 x DVI-I female Computer 1 x DE-15 VGA female Connectors 1 x USB type B (per port) 2 x 3.5mm mini-jack 1 x DVI-I female 1 x DE-15 VGA female Console Connectors 4 x USB type A 2 x 3.5mm mini-jack... -
Page 15: Technical Support
Limitation of Liability In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or... - Page 16 StarTech.com has been making “hard-to-find easy” since 1985, providing high quality solutions to a diverse IT and A/V customer base that spans many channels, including government, education and industrial facilities to name just a few. We offer an unmatched selection of computer parts, cables, A/V products, KVM and Server...
Need help?
Do you have a question about the SV231DDVDUA and is the answer not in the manual?
Questions and answers