Page 1
PT-DZ10K P ro d u c t N u m b e r : 3-Chip DLP ™ Projector P ro d u c t N a m e : As of April 2013. Specifications and appearance are subject to change without notice.
PT-DZ10K 3-Chip DLP ™ Projector Specifications Main unit Power supply 120 V AC, 9 A, 50/60 Hz 220–240 V AC, 4.7 A, 50/60 Hz Power consumption 120 V AC, 50/60 Hz 925 W (1,010 VA) (0.2 W with standby mode set to eco.* 6 W with standby mode set to normal.
Page 3
PT-DZ10K 3-Chip DLP Projector ™ Keystone correction range Vertical ±40°, horizontal ±15° (vertical ±22° and horizontal ±15° with the ET-D75LE5/LE50, vertical ±28° and horizontal ±15° with the ET-D75LE6) When using only the KEYSTONE correction of the Geometric Adjustment function: Vertical ±40°, horizontal ±15°...
Page 4
PT-DZ10K 3-Chip DLP ™ Projector Remote control unit Power supply 3 V DC (AA/R6 type battery × 2) Operation range* Approx. 30 m (98 5 in) when operated from directly in front of the signal receptor Dimensions (W × H × D) 51 ×...
Page 5
PT-DZ10K 3-Chip DLP Projector ™ Dimensions unit : mm (inch) NOTE: This illustration is not drawn to scale. 462 (18-3/16) 468 (18-7/16) 530 (20-7/8) (1-1/32) Terminals Remote 1 input Remote 1 output Remote 2 input Serial input Serial output SDI input...
PT-DZ10K 3-Chip DLP Projector ™ Standard setting-up position *1 When the lens protrudes to the maximum. φ60.5 212 mm (8-11/32) with the ET-D75LE6 Upper edge of projected image 125 mm (4-29/32) with the ET-D75LE10 (12-3/8) 121 mm (4-3/4) with the ET-D75LE20...
PT-DZ10K 3-Chip DLP ™ Projector Projection distance for 16:10 aspect ratio screen (ET-D75LE6/D75LE10/D75LE20/D75LE30/D75LE40/D75LE8/D75LE50) Unit: meters Screen size Distance to screen (L) Height from the edge of screen to center of lens (H) (diagonal) Zoom Fixed-focus Zoom lenses Fixed- ET-D75LE6 ET-D75LE10...
PT-DZ10K 3-Chip DLP ™ Projector Projection distance for 16:9 aspect ratio screen (ET-D75LE6/D75LE10/D75LE20/D75LE30/D75LE40/D75LE8/D75LE50) Unit: meters Screen size Distance to screen (L) Height from the edge of screen to center of lens (H) (diagonal) Zoom Fixed-focus Zoom lenses Fixed- ET-D75LE6 ET-D75LE10...
PT-DZ10K 3-Chip DLP ™ Projector Calculation of the projection distance For a screen size different from the above, use the equation below to calculate the projection distance. Aspect ratio 16:10 Zoom lenses ET-D75LE6 minimum L (m) = (diagonal screen size in inches) × 0.0201 – 0.0566 maximum L (m) = (diagonal screen size in inches) ×...
Page 10
PT-DZ10K 3-Chip DLP ™ Projector Shift range Optical axis shift function allows to shift the position of a projected image as shown below. • • When the lens except the ET-D75LE6 is mounted When the ET-D75LE6 is mounted (Width of (Width of 0.2H...
PT-DZ10K 3-Chip DLP ™ Projector List of compatible signals The signals that can be input to this projector are shown in the table below. Horizontal scanning fre- quencies of 15 kHz to 100 kHz, vertical scanning frequencies of 24 Hz to 120 Hz, and a dot clock of 162 MHz maximum can be input.
Page 13
PT-DZ10K 3-Chip DLP ™ Projector Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, com- mands must be input through communication software, based on the format and satisfying the commu- nication conditions shown below.
Page 14
PT-DZ10K 3-Chip DLP ™ Projector Cable specifications Control commands Command : Parameter Function Callback P O N PO N Standby power on POWER (STANDBY) P O F PO F Standby power off O S H : 0 OS H: 0...
Page 15
PT-DZ10K 3-Chip DLP ™ Projector Status request commands Command : Parameter Function Callback Description Q P W Main power status Q S H Shutter function status Q I N Input signal status DVI -D RGB 1 RGB 2 Video Q S L...
Page 16
PT-DZ10K 3-Chip DLP ™ Projector Notes on projector placement and operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. 1. Never place objects on top of the projector while it is operating.
PT-DZ10K 3-Chip DLP ™ Projector Direction of air intake and exhaust Intake Exhaust Operating the projector continuously If the projector is to be operated continuously one week, use the dual-lamp optical system’s alternating lamp operation (lamp relay) function. The projector cannot be operated continuously one week in dual-lamp mode.