Page 1 N8100-1644F/1645F/1646F/1647F/1648F/1649F N8100-1650F/1651F/1652F/1653F NEC Express5800/R120b-2 User's Guide 2nd Edition 7-2010 ONL-510_017_02_R120b2-100-00-1007...
Page 2 The NEC product(s) discussed in this document are warranted in accordance with the terms of the Warranty Statement accompanying each product. However, actual performance of each such product is dependent upon factors such as system configuration, customer data, and operator control.
Page 3 Keep this manual at hand for quick reference at anytime necessary. SAFETY INDICATIONS Follow the instructions in this manual for your safety to use the NEC Express server. Your server contains components with possible danger, hazards that may cause by ignoring warnings, and preventive actions against such hazards.
Page 4 SYMBOLS USED IN THIS MANUAL AND WARNING LABELS Attentions Indicates that improper use may cause an electric shock. Indicates that improper use may cause fingers to be caught. Indicates that improper use may cause personal injury. Indicates that improper use may cause personal injury. Indicates that improper use may cause fumes or fire.
Page 5 If you notice any part unclear, incorrect, or omitted in this User's Guide, contact the sales agent where you purchased this product. (5) NEC assumes no liability arising from the use of this product, nor any liability for incidental or consequential damages arising from the use of this User's Guide regardless of Item (4).
Page 6 Trademarks NEC ESMPRO and NEC EXPRESSBUILDER are trademarks of NEC Corporation. Microsoft, Windows, Windows Server, and MS-DOS are registered trademarks or trademarks of Microsoft Corporation in the United States and other countries. Intel, Pentium, and Xeon are registered trademarks of Intel Corporation.
Page 7: Preface
Purchase of this server is your assurance of receiving state-of-the-art, high quality hardware to meet your needs, both now and in the future. Read this User's Guide thoroughly to fully understand handling of the NEC Express server and appreciate its functions to the maximum extent.
Page 8: About This User's Guide
Chapter 6 Installing and Using Utilities describes how to install the utilities for the server. It also includes a description on using the attached "NEC EXPRESSBUILDER" DVD-ROM. Chapter 7 Maintenance provides you with all the information necessary to maintain successful operation of the server.
Page 9: Text Conventions
Appendix I Accessing Power and Performance Data describes how to collect the power and performance data, including power consumption, inlet air temperature, and processor utilization of NEC Express server. Appendix J Product Configuration Record Table provides a table to be filled with your server configuration.
Page 10: In The Package
IN THE PACKAGE The carton contains various accessories, as well as the server itself. See the packing list to make sure that you have everything and that individual components are not damaged. If you find any component missing or damaged, contact your service representative. Store the provided accessories in a designated place for your convenience.
Page 11: Table Of Contents
Rear View..........................2-6 Internal View ..........................2-8 Motherboard ..........................2-10 Standard Features........................2-11 Peripheral Bays ........................2-12 AC LINK Feature........................2-12 Security ..........................2-12 NEC EXPRESSBUILDER.....................2-13 NEC ESMPRO........................2-14 Maintenance Tools .........................2-14 System Diagnostic Utility ......................2-14 Remote Management......................2-15 Using Your Server........................2-16 Installing or Removing the Front Bezel .................2-16 POWER Switch........................2-18...
Page 12 Chapter 3 Setting Up Your Server ................3-1 Setup Flow............................3-2 Selecting Server Site........................3-3 Installing the Server........................3-5 Installation..........................3-6 Removal ..........................3-14 Connecting Peripheral Devices....................3-18 Connecting Power Cord......................3-20 Turning On the Server ........................3-22 Installing Operating System .......................3-24 Installing Utilities ........................3-24 Making Backup Copies of System Information................3-24 Chapter 4 Configuring Your Server................
Page 13 NEC ESMPRO Agent Extension....................6-22 NEC ExpressUpdate Agent......................6-23 Universal RAID Utility.......................6-24 Setup with Express Setup .......................6-24 Manual Setup .........................6-25 Creating Logical Drive of RAID 6..................6-26 NEC Product Info Collection Utility ..................6-27 Installation..........................6-27 Using Utility...........................6-28 Uninstallation .........................6-28 Chapter 7 Maintenance....................7-1 Making Backup Copies.........................7-1 Cleaning............................7-2...
Page 14 Messages displayed by RAID Controller during POST ............8-18 Beep Codes..........................8-22 Error messages on virtual LCD ....................8-23 Solving Problems........................8-26 Problems with NEC Express Server..................8-26 Problems with Windows......................8-31 Problems with RAID System Configuration ................8-40 Problems with NEC EXPRESSBUILDER ................8-42 Problems with Express Setup ....................8-44 Problems with Parameter File Creator ...................8-45...
Page 15 Mouse............................B-6 Appendix C IRQ......................C-1 Appendix D Installing Windows Server 2008 R2 ............D-1 Notice ............................D-1 Optional Board Supported by NEC EXPRESSBUILDER............D-1 Service Pack Which EXPRESSBUILDER Supports ..............D-2 Installing Service Pack ......................D-2 Updating System ........................D-2 Installing on the Mirrored Volume ..................D-2 Mounting MO Device ......................D-2...
Page 16 About Windows Activation ....................D-22 Setting for Solving Problems.....................D-26 Appendix E Installing Windows Server 2008 .............. E-1 Notice ............................E-1 Optional Board Supported by NEC EXPRESSBUILDER............E-1 Service Pack Which EXPRESSBUILDER Supports .............. E-2 Installing Service Pack ......................E-2 Updating System ........................E-2 Installing on the Mirrored Volume ..................
Page 17 About Windows Activation ....................F-28 Setting for Solving Problems..................... F-30 Appendix G Installing Windows Server 2003..............G-1 BEFORE INSTALLING WINDOWS SERVER 2003 ..............G-1 Optional Board Supported by NEC EXPRESSBUILDER............G-1 Service Pack Which EXPRESSBUILDER Supports ..............G-2 Application of Service Pack ....................G-2 Updating System ........................G-2 Re-installing to the Hard Disk which has been upgraded to Dynamic Disk ......G-2...
Page 18 Appendix I Accessing Power and Performance Data ..........I-1 Power Consumption ........................I-1 Inlet Air Temperature........................I-3 Processor Utilization........................I-8 Appendix J Product Configuration Record Table ............J-1 Hardware ..........................J-1 Software ........................... J-3...
Page 19: Chapter 1 Notes On Using Your Server
Chapter 1 Notes on Using Your Server This chapter includes information necessary for proper and safe operation of your server.
Page 20: Warning Labels
1-2 Notes on Using Your Server WARNING LABELS The warning label is attached to components with possible danger or their vicinity in your server to inform the user that a hazardous situation may arise when operating the server. (Do not intentionally remove or damage any of the labels.) If you find any labels totally/partially removed or illegible due to damage, contact your sales representative.
Page 21 Notes on Using Your Server 1-3 3.5-inch disk model...
Page 22: Internal View
1-4 Notes on Using Your Server Internal View 2.5-inch disk model...
Page 23 Notes on Using Your Server 1-5 3.5-inch disk model...
Page 24: Safety Notes
NEC assumes no liability for any accident resulting in personal injury, death, or property damage if the server has been used in the above conditions.
Page 25 Notes on Using Your Server 1-7 CAUTION Keep water or foreign matter away from the server. Do not let any form of liquid (water etc.) or foreign matter (e.g., pins or paper clips) enter the server. Failure to follow this warning may cause an electric shock, a fire, or a failure of the server.
Page 26: Rack
1-8 Notes on Using Your Server Rack CAUTION Do not carry or install the server only by a single person. More than one person is required to carry or install the rack. Failure to follow this instruction may cause the rack to fall to result in personal injury and/or breakages of surrounding devices.
Page 27: Power Supply And Power Cord Use
Notes on Using Your Server 1-9 Power Supply and Power Cord Use WARNING Do not hold the power plug with a wet hand. Do not disconnect/connect the plug while your hands are wet. Failure to follow this warning may cause an electric shock. Do not connect the ground wire to a gas pipe.
Page 28: Installation, Relocation, Storage, And Connection
1-10 Notes on Using Your Server Installation, Relocation, Storage, and Connection WARNING Disconnect the power cord(s) before installing or removing the server. Make sure to power off the server and disconnect the power cord(s) from a power outlet before installing/removing the server. All voltage is removed only when the power cords are unplugged.
Page 29 Do not use any unauthorized interface cable. Use only interface cables provided by NEC and locate a proper device and connector before connecting a cable. Using an authorized cable or connecting a cable to an improper destination may cause a short circuit, resulting in a fire.
Page 30: Cleaning And Working With Internal Devices
1-12 Notes on Using Your Server Cleaning and Working with Internal Devices WARNING Do not disassemble, repair, or alter the server. Never attempt to disassemble, repair, or alter the server on any occasion other than described in this User's Guide. Failure to follow this instruction may cause an electric shock or fire as well as malfunctions of the server.
Page 31: During Operation
Notes on Using Your Server 1-13 During Operation CAUTION Do not pull out or remove the server from the rack unnecessarily. Do not pull out or remove the server from the rack unnecessarily. Pulling out or removing the server from the rack may cause not only the server to operate incorrectly but also the server to fall on people to make them injured.
Page 32: For Proper Operation
1-14 Notes on Using Your Server FOR PROPER OPERATION Observe the following notes for successful operation of the server. Use of the server ignoring the notes will cause malfunctions or failures of the server. Install the rack assembly in a place that meets requirements for successful operation. For details, see Chapter 3, "Setting Up Your Server."...
Page 33: Transfer To Third Party
Notes on Using Your Server 1-15 TRANSFER TO THIRD PARTY The following must be observed when you transfer (or sell) the server or software provided with the server to a third party: Make sure to provide this manual along with the server to a third party. IMPORTANT: About data on the hard disk drive Be sure to take appropriate measures not to leak important data (e.g.,...
Page 34: Disposal And Consumables
For stable operation of the server, NEC recommends you replace these components on a regular basis. Consult with your service representative for replacement.
Page 35: User Support
Notes on Using Your Server 1-17 USER SUPPORT Before Asking for Repair, do the following when the server appears to fail: Check if the power cord and the cables to other devices are properly connected. See Chapter 8 to find if your problem fits the description. If it does, take the recommended measure for it.
Page 36 1-18 Notes on Using Your Server Advice for Health The longer you keep using the computer equipment, the more you become tired, which may cause disorders of your body. When you use a computer, observe the following to keep yourself from getting tired: Good Working Posture You have good posture if the following are satisfied when you use a computer:...
Page 37: Chapter 2 General Description
Chapter 2 General Description This chapter provides information that you should be familiar with before using the server. It includes names and functions of the components and features of the server. OVERVIEW Your server is a modular, multiprocessing server based on the Intel Xeon microprocessor.
Page 38: External View
2-2 General Description EXTERNAL VIEW 2.5-inch disk model 3.5-inch disk model Drive cover Logic cover Hard disk drive bay Backup device bay Optical Disk drive bay...
Page 39: Names And Functions Of Parts
General Description 2-3 NAMES AND FUNCTIONS OF PARTS The following figure shows the location of the front system features. Front View with Front Bezel Closed (4)-1 (4)-2 Front bezel This cover protects the front devices and the drive cover on top of the server during daily use. A security key is provided to lock the cover.
Page 40: Front View With Front Bezel Removed
2-4 General Description Front View with Front Bezel Removed 2.5-inch disk model See (3) to (7) on previous page. (11) (10) (3)-2 (3)-0 (3)-4 (3)-6 (12) (3)-1 (3)-3 (3)-5 (3)-7 (3)-8* (3)-9* * When N8154-35 has been added (3)-10* (3)-11* 3.5-inch disk model See (3) to (7) on previous page.
Page 41: General Description
General Description 2-5 Handles (1 at the right and left each) Hold the handles when dismounting/mounting the server from/in the rack. Optical disk drive bay Attach an optional optical disk drive. (See page 2-24.) One of the following drives will be installed, according to the model or the purchase order. −...
Page 42: Rear View
2-6 General Description Rear View (15) (13) (12) (11) (10) (9) (8) (14) (16) (17)- (18) (19) (16) (18) (16) (18) (17)-2 Full-height PCI card slot (1B) These slots are used to insert full-height PC cards. (For details, see page 9-51.) Starting at the top, these slots are 3B and 2B.
Page 43 General Description 2-7 This LED lights up when the UID switch is pressed. This LED can also turned on or set to the blinking status by using a software command. (13) USB connectors These connectors are used to connect devices that support the USB interface. (For details, see page 3-18.) (14) Monitor connector...
Page 44: Internal View
2-8 General Description Internal View The processor duct is not shown in the figure. 2.5-inch Disk Model (2)-1 (2)-2 (2)-5 (2)-6 (2)-7 (2)-3 (10) (2)-4 (2)-8 Front panel board Cooling fans (2)-1 FAN1R (2)-2 FAN2R (2)-3 FAN3R (2)-4 FAN4R (2)-5 FAN1F (option) (2)-6 FAN2F (option) (2)-7 FAN3F (option) (2)-8 FAN4F (option)
Page 45: Inch Disk Model
General Description 2-9 3.5-inch Disk Model (2)-2 (2)-5 (2)-1 (2)-6 (2)-7 (10) (2)-8 (2)-3 (2)-4 Front panel board Cooling fans (2)-1 FAN1R (2)-2 FAN2R (2)-3 FAN3R (2)-4 FAN4R (2)-5 FAN1F (option) (2)-6 FAN 2F (option) (2)-7 FAN3F (option) (2)-8 FAN4F (option) Supporting bar Power supply Motherboard...
Page 46: Motherboard
2-10 General Description MOTHERBOARD (2) (3) (4) (5) (6) (10) (9) (3) (13) (21) (11) (12) (22)-2 External connectors (see page 158) (22)-1 (21) REAR FRONT (20) (19) (18)(15) (16) (17) (14) Power connector USB backup device connector Unused connector USB connector (front) SATA DVD connector SATA backup device connector...
Page 47: Standard Features
Large memory of up to 192GB Test and Diagnosis (T&D) Up to two multi-processors are available for Easy setup upgrade. NEC EXPRESSBUILDER (system setup Three network ports (one for management LAN) utility) Hard disk drive bays Parameter File Creator 2.5-inch disk model: up to 12 hard disk drives SETUP (BIOS configuration utility) 3.5-inch disk model: up to 6 hard disk drives...
Page 48: Peripheral Bays
2-12 General Description Peripheral Bays The system supports a variety of standard PC AT-compatible peripheral devices. The chassis includes these peripheral bays: Three 5.25-inch file bays for installing 5.25-inch peripheral devices such as optional tape drives. (An optical disk drive is factory-installed.) The 3.5-inch disk cage can contain up to four SATA or SAS hard disk drives.
Page 49: Nec Expressbuilder
General Description 2-13 NEC EXPRESSBUILDER The DVD of this server's accessories contains a setup utility called "NEC EXPRESSBUILDER". The major functions of the NEC EXPRESSBUILDER are: To install the Operating System. "Express Setup" helps you to install the Windows Operating System. (See Chapter 5) To diagnose the server.
Page 50: Nec Esmpro
The NEC ESMPRO is server management software that runs on the OS. The NEC ESMPRO Manager is a management software that enables you to manage and monitor the servers remotely. To use this software, it is required to install apposite bundled software on the server.
Page 51: Remote Management
Remote management via LAN/WAN by using NEC ESMPRO Manager and centralized management of several systems For more information about remote management using Web browser, remote KVM feature, and remote device feature, refer to the "EXPRESSSCOPE Engine 2 User's Guide" stored in NEC EXPRESSBUILDER DVD-ROM. NOTE:...
Page 52: Using Your Server
2-16 General Description USING YOUR SERVER This section describes the basic operations of the server including how to use devices such as the optical disk drive. Installing or Removing the Front Bezel When turning the power of the server on/off, accessing the optical disk drive and the backup file device, or installing or removing a hard disk drive on or from a hard disk drive bay, first remove the front bezel.
Page 53 General Description 2-17 Slide the front bezel to the left a little to release the tab from the frame and then remove the front bezel from the server. <2> <1> To install the front bezel, latch the tab at the left side of the front bezel on the server frame. After the installation, lock the front bezel by using the security key.
Page 54: Power Switch
2-18 General Description POWER Switch Use the POWER switch to turn on/off the server. Power On Press the POWER switch on the front of the computer chassis. The POWER LED lights in green. POWER LED POWER switch IMPORTANT: If the power cord is connected to a power control device such as a UPS (Uninterruptive Power Supply), make sure that the power control device is powered.
Page 55 ECC memory module, CPU module, keyboard, and mouse. POST also displays messages of the BIOS Setup utility, such as the start-up message, while in progress. With the factory setup of the server, the NEC logo appears on the display unit while POST is in progress. (To display the POST check results, press Esc.) You do not always need to check the POST check results.
Page 56: Post Execution Flow
2-20 General Description POST Execution Flow The following describes the progress of POST in the chronological order. IMPORTANT: Do not power off the server while POST is in progress. Do not make key entries or perform mouse operations while POST is in progress.
Page 57 General Description 2-21 If your server uses Onboard RAID Controller, the following message is displayed to prompt you to run RAID utility. Press <Ctrl><M> to Run LSI SoftwareRAID Configuration Utility Press Ctrl + M to run the utility. For detail explanation, see Chapter 4 for detail. IMPORTANT: The LSI Software RAID Configuration Utility is used to manage the data stored in hard disk drive, or for maintenance.
Page 58: Power Off
2-22 General Description Power Off Follow the procedure below to power off the server. If the power cord of the server is connected to a UPS, refer to the manual that comes with the UPS or the manual for the application that controls the UPS.
Page 59: Identification Of Servers ~ Uid Switch
General Description 2-23 IDENTIFICATION OF SERVERS ~ UID SWITCH ~ A UID (Unit ID) LED is provided on the front panel and rear panel. If more than one server is mounted in a single rack, the LED identifies the server you are performing maintenance on. The UID LED turns on or blinks when the UID (Unit ID) switch on the front panel is pressed.
Page 60: Optical Disk Drive
2-24 General Description OPTICAL DISK DRIVE The server is provided with the optical disk drive bay on its front to read data from a disc. The following optical disk drives can be installed in this server: DVD-ROM drive (option) This drive can read a variety of optical discs. DVD Super Multi drive (option) This drive can read and write a variety of optical discs.
Page 61 General Description 2-25 As shown in the figure below, hold the tray with a hand and press the disc with fingers of another hand to make the hole of the disc fit to the rotor at the center of the tray. Rotor Press this part of disc.
Page 62 2-26 General Description After taking out the disc, return the tray into the drive. If you fail to eject the tray with the Eject button and remove the disc from the server, follow the procedure below. Manual ejection hole Press the POWER switch to power off the server. (The POWER LED goes off.) Insert a metal pin of approximately 1.2 mm in diameter and 100 mm in length (a straightened large paper clip will suffice) into the manual ejection hole on the right front of the optical disk drive and gently push it in until the tray is ejected.
Page 63: Flash Fdd
The Flash FDD is only intended as a temporary means of performing processing such as reading device drivers during installation, so do not use the FDD to back up data. Compensation for recorded data NEC will not pay compensation for data recorded on the Flash FDD if the data is lost.
Page 64 2-28 General Description Notes on handling the Flash FDD Do not turn off the server while the access LED of the Flash FDD is blinking. Turning off the server at this time can cause a failure or data corruption. The Flash FDD is a consumable. →...
Page 65: Chapter 3 Setting Up Your Server
Chapter 3 Setting Up Your Server This chapter describes how to set up the server appropriate for your system, on a step-by-step basis.
Page 66: Setup Flow
Install an operating system to the server. See Chapter 5. Installing the utilities Install the utilities in the provided NEC EXPRESSBUILDER DVD. See Chapter 6. Making backup copies of system information After all the system setup procedures are completed, make backup copies of system information.
Page 67: Selecting Server Site
Setting Up Your Server 3-3 SELECTING SERVER SITE To use the server, install it on a standard EIA 19-inch rack assembly. Refer to the documentation attached to the rack or contact your service representative for the installation of the server on the rack. WARNING Observe the following instructions to use the server safely.
Page 68 3-4 Setting Up Your Server Do not install the rack in the places listed below. Installing the rack or mounting the server on the rack in such a place may cause some malfunction to occur. Narrow space from which devices cannot be pulled out from the rack completely Place that cannot bear the total weights of the rack and devices mounted on the rack Place where stabilizers cannot be installed or where the rack can be installed only after the practice of proper earthquake-resistant construction...
Page 69: Installing The Server
Setting Up Your Server 3-5 INSTALLING THE SERVER This subsection provides the instructions for installing the server into a rack cabinet. (This subsection also describes the removal procedures.) WARNING Observe the following instructions to use the server safely. Failure to follow these instructions may result in death or serious personal injury.
Page 70: Installation
3-6 Setting Up Your Server Installation This server can be installed in either the NEC rack or a third vendor's rack. Take the following steps to install the server in the rack. Preparation for installation When shipped from factory, the left and right slide rails are fixed with tapes at the front and side faces to prevent from falling off during transportation.
Page 71 Setting Up Your Server 3-7 While pushing the unlock button on the front of the server, hold the rails and slowly move them toward the rear of the server. Press this button to unlock the server. After a while, the rails are locked with clicking sound. Pull the release levers on the left and right sides of the server toward direction indicated by an arrow (white) in the figure, and remove them from the server while unlocking it.
Page 72 3-8 Setting Up Your Server While pushing the levers, move the removed rail assemblies toward the direction indicated by an arrow in the figure, to restore the original position. IMPORTANT: The removed rail assemblies are to be installed on the inner rails later.
Page 73 Setting Up Your Server 3-9 Installing Rail Assemblies Insert the square projection of the rail assembly into the angle hole on the 19-inch rack until it is locked with clicking sound. The figure below shows the right side (front) of the rack. Install the rail assemblies to the right side (rear), and left side (front and rear) of the rack in the same procedure.
Page 74 3-10 Setting Up Your Server Installing the Server CAUTION Observe the following instructions to use the server safely. Failure to follow these instructions may cause a fire, personal injury, or property damage. See pages 1-4 to 1-11 for details. Do not lift the server only by a single person. Do not pinch your finger with mechanical components.
Page 75 Setting Up Your Server 3-11 At least two persons are required to install the server. Securely hold the server and install it in the rack. Firmly fit the inner rails on the sides of the server into the rail assemblies that are installed on the rack, and then slowly push the server into the rack.
Page 76 3-12 Setting Up Your Server IMPORTANT: Be very careful not to get your finger caught in the levers or rails. Insert both sides of inner rails straight into the rack. Hold the thumbscrews on both sides of the server, and install the server carefully while making sure the installation position.
Page 77 Setting Up Your Server 3-13 Installing the Front Bezel Install the front bezel so that the left tab on the front bezel engages with the chassis frame. <1> <2>...
Page 78: Removal
3-14 Setting Up Your Server Removal Remove the server from the rack in the following procedure. CAUTION Observe the following instructions to use the server safely. Failure to follow these instructions may cause a fire, personal injury, or property damage. See pages 1-4 to 1-11 for details.
Page 79 Setting Up Your Server 3-15 While pushing the left and the right unlock buttons on the front of the server, pull out the server from the rack slowly and carefully. The server clicks to be latched. Press this button to unlock the server.
Page 80 3-16 Setting Up Your Server Removing Rail Assemblies Remove the rail assembly from the 19-inch rack in the following procedure. CAUTION Observe the following instructions to use the server safely. Failure to follow these instructions may cause a fire, personal injury, or property damage. See pages 1-4 to 1-11 for details.
Page 81 Setting Up Your Server 3-17 Unlock the rail assembly. Unlock the rail assembly by applying force to the tool in the direction shown by an arrow. Locking spring Viewed from front Viewed from top While the rail assembly is being unlocked, remove it from the rack. Insert the tool into the angle hole at the rear of rail assembly to unlock it.
Page 82: Connecting Peripheral Devices
See pages 1-4 to 1-11 for details. Do not connect any interface cable with the power cord of the NEC Express Server plugged to a power source. Do not use any unauthorized interface cable.
Page 83: Setting Up Your Server
Setting Up Your Server 3-19 Display unit FRONT Device with the serial interface Mouse USB device 1000BASE-T/ 100BASE-TX 10BASE-T REAR 100BASE-TX 10BASE-T Finally connect the provided Keyboard Hub or USB device power cord to the receptacle. switching hub If connecting the server to Display unit UPS, see the explanation below.
Page 84: Connecting Power Cord
3-20 Setting Up Your Server CONNECTING POWER CORD Connect the provided power cord to the server. WARNING Observe the following instructions to use the server safely. Failure to follow these instructions may result in death or serious personal injury. See pages 1-4 to 1-11 for details.
Page 85 Setting Up Your Server 3-21 To connect the power cord from the server to an uninterruptive power supply (UPS), use service outlets on the rear of the UPS. Refer to the manual that comes with the UPS. When the power cord from the server to a UPS, change the BIOS setup of the server to link with power supply from the UPS.
Page 86: Turning On The Server
3-22 Setting Up Your Server TURNING ON THE SERVER Power on your system as follows. Make sure all external devices, such as a video display, keyboard, and mouse (optional) have been connected, and the power cords are connected. Power on the video display and any other external devices. NOTE: If the server power cord(s) is connected to a power control unit such as an UPS (Uninterruptible Power Supply), make sure that the...
Page 87 If you have problems powering on your system, see Chapter 8. After you have successfully powered on your system, insert the NEC EXPRESSBUILDER DVD into the optical disk drive, restart the system and follow the screen prompts to run NEC EXPRESSBUILDER.
Page 88: Installing Operating System
Without the backup data, you will not be able to recover the information. You can save the information by the following process. Connect Flash FDD or USB FDD to the USB connector. Insert the NEC EXPRESSBUILDER DVD into the optical disk drive and reboot the system. Select [Tool menu (Normal mode)].
Page 89: Chapter 4 Configuring Your Server
Chapter 4 Configuring Your Server Configuration and setup utilities are used to change your system configuration. You can configure your system, as well as option boards you may add to your system, using the BIOS SETUP Utility. Several unique system parameters are configured using the BIOS SETUP, which is stored in the system FLASH memory.
Page 90: System Bios (Setup)
4-2 Configuring Your Server SYSTEM BIOS (SETUP) This section describes how to specify Basic Input Output System (BIOS) settings. Make sure you understand the information in this section so you can specify the correct settings when installing the server or adding or removing an optional component. The SETUP utility is used to change system configuration parameters.
Page 91: Starting Setup Utility
Configuring Your Server 4-3 Starting SETUP Utility Turning on the server starts POST (Power On Self-Test) and displays its check results. If the NEC logo is displayed, press Esc. After a few seconds, the following message appears at the bottom left of the screen.
Page 92: Description On On-Screen Items And Key Usage
4-4 Configuring Your Server Description on On-Screen Items and Key Usage Use the following keyboard keys to work with the SETUP utility. Indicates the current menu. Indicates there are submenus. Help window Setup item menu(s)* Parameter (high-lights upon selection) menu * Items displayed in gray are automatically specified or detected, cannot be changed, or can only be changed by entering a password.
Page 93: Menu And Parameter Descriptions
Configuring Your Server 4-5 Menu and Parameter Descriptions The SETUP utility has the following six major menus: Main Advanced Security Server Boot Save & Exit To specify detailed feature settings, select a submenu from the above menus. The following describes available functions and parameters, as well as the factory settings, for each menu.
Page 94 4-6 Configuring Your Server Main When you start up the setup utility, the Main menu is displayed first. The following table shows the items that can be specified on the Main menu screen and their functions. Option Parameters Description BIOS Information –...
Page 95: Configuring Your Server
Configuring Your Server 4-7 IMPORTANT: Be sure to confirm that the date and time in the BIOS parameters are correctly specified. In any of the following situations, check the system time before using the server: After transporting the server After removing the server from storage After setting the server to "Hibernate"...
Page 96 4-8 Configuring Your Server Advanced When the cursor is moved to the [Advanced] position, the Advanced menu is displayed. If an item with an arrow displayed to its left (all menus in this section) is selected and then the Enter key is pressed, a submenu is displayed in which settings are specified.
Page 97: Processor Configuration Submenu
Configuring Your Server 4-9 Processor Configuration submenu When [Processor Configuration] is selected in the Advanced menu and then the Enter key is pressed, the screen below is displayed. If an item with an arrow displayed to its left is selected and then the Enter key is pressed, a submenu is displayed.
Page 98 4-10 Configuring Your Server Option Parameters Description Specify whether to enable or disable the Hardware Prefetcher Disabled Hardware Prefetcher of the processor. [Enabled] This menu appears and becomes accessible when [Custom] is specified for [Server Class]. Adjacent Cache Line Disabled Specify whether to enable or disable the Prefetch optimal access to the cache line from the...
Page 99: Processor Information Submenu
Configuring Your Server 4-11 Processor Information submenu Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc. Main Advanced Security Server Boot Save & Exit P r o c e s s o r 1 C P U I D 1 0 6 a 4 P r o c e s s o r T y p e I n t e l ( R ) X e o n ( R ) C P U...
Page 100: Memory Configuration Submenu
4-12 Configuring Your Server Memory Configuration submenu When [Memory Configuration] is selected in the Advanced menu and then the Enter key is pressed, the screen below is displayed. If an item with an arrow displayed to its left is selected and then the Enter key is pressed, a submenu is displayed.
Page 101: Memory Information Submenu
Configuring Your Server 4-13 Memory Information submenu For details about the options, see the following table (display only). Option Parameters Description − Total Memory Displays the basic memory capacity. − Displays the amount of available memory in Available under 4GB an area at 4GB or less.
Page 102: Pci Configuration Submenu
4-14 Configuring Your Server PCI Configuration submenu When [PCI Configuration] is selected in the Advanced menu and then the Enter key is pressed, the screen below is displayed. Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc. Main Advanced Security Server Boot...
Page 103: Advanced Chipset Configuration Submenu
Configuring Your Server 4-15 Advanced Chipset Configuration submenu When [Advanced Chipset Configuration] is selected in the Advanced menu and then the Enter key is pressed, the screen below is displayed. Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc. Main Advanced Security...
Page 104 4-16 Configuring Your Server SATA Configuration submenu When [SATA Configuration] is selected in the Advanced menu and then the Enter key is pressed, the screen below is displayed. If an item with an arrow displayed to its left is selected and then the Enter key is pressed, a submenu is displayed.
Page 105 Configuring Your Server 4-17 SATA Information submenu For details about the options, see the following table (display only). Option Parameters Description SATA Port0 − Displays the devices connected to each channel. SATA Port1 SATA Port2 SATA Port3 SATA Port4 SATA Port5 ]: Factory-set...
Page 106: Usb Configuration Submenu
4-18 Configuring Your Server USB Configuration submenu When [USB Configuration] is selected in the Advanced menu and then the Enter key is pressed, the screen below is displayed. Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc. Main Advanced Security Server Boot...
Page 107 Configuring Your Server 4-19 Serial Port Configuration submenu When [Serial Port Configuration] is selected in the Advanced menu and then the Enter key is pressed, the screen below is displayed. For details about the options, see the following table. Option Parameters Description Serial Port A Settings...
Page 108 4-20 Configuring Your Server Option Parameters Description Specify whether to enable or disable BIOS Redirection Port [Disabled] direct connections from the Serial Port A management terminal using the Serial Port B ESMPRO Manager or hyper terminal from the serial port specified for this menu item.
Page 109 Configuring Your Server 4-21 Security When the cursor is moved to the [Security] position, the Security menu is displayed. If an item with an arrow displayed to its left is selected and then the Enter key is pressed, a submenu is displayed in which settings are specified. When the Enter key is pressed while Administrator Password or User Password is selected, the screen for registering or changing the password is displayed.
Page 110 4-22 Configuring Your Server For details about the options, see the following table. Security settings can be specified in the submenu that opens by selecting [Security Configuration] and pressing Enter. Option Parameter Description Password – – Configuration Administrator Up to 20 alphanumeric When the Enter key is pressed, the Password characters...
Page 111 Configuring Your Server 4-23 Trusted Computing submenu When [Trusted Computing] is selected in the Security menu and then the Enter key is pressed, the screen below is displayed. For details about the options, see the following table. Option Parameter Description TPM Configuration –...
Page 112 5 to 60 minutes time limit. To use this function, install NEC ESMPRO Agent. Set this item to [Disabled] if the system is booted from an OS without NEC ESMPRO Agent installed.
Page 113 Configuring Your Server 4-25 Option Parameters Description Boot Monitoring Specify the processing when a timeout occurs during [Retry 3 Times] Policy boot monitoring. This option can only be specified if Always Reset [Boot Monitoring] is specified. If [Retry 3 times] is selected, the system is reset after the occurrence of a timeout and booting up the OS is retried up to three times.
Page 114 4-26 Configuring Your Server The table below shows the operation when the AC power to the server is turned off once and then back on, in accordance with the [AC LINK] setting. Setting of AC LINK System status before AC power off Stay Off Last State Power On...
Page 115 Configuring Your Server 4-27 System Management submenu When [System Management] is selected in the Server menu and then the Enter key is pressed, the screen below is displayed. For details about the options, see the following table (display only). Option Parameters Description BIOS Version...
Page 116 4-28 Configuring Your Server BMC LAN Configuration submenu When [BMC LAN Configuration] is selected in the Server menu and then the Enter key is pressed, the screen below is displayed. IMPORTANT: The management-dedicated LAN connector cannot be used for a different LAN. For details about the options, see the following table.
Page 117 Configuring Your Server 4-29 Option Parameters Description DHCP Disabled Set to [Enabled] to obtain an IP address from Enabled the DHCP server automatically. If you intend to specify an IP address manually, set to [Disabled]. Web Interface – – HTTP Disabled Set to [Enabled] to use HTTP communication Enabled...
Page 118 4-30 Configuring Your Server Event Log Configuration submenu When [Event Log Configuration] is selected in the Server menu and then the Enter key is pressed, the screen below is displayed. If an item with an arrow displayed to its left is selected and then the Enter key is pressed, a submenu is displayed.
Page 119 Configuring Your Server 4-31 System Event Log submenu When [System Event Log] is selected for [Event Log Configuration] on the Server menu, the screen below is displayed. In addition, when [View System Event Log] is selected, the screen below is displayed. The following shows the system event log settings as an example.
Page 120 It might take a few moments until initialization completes after execution of Clear BMC Configuration. If you are using NEC ESMPRO Agent Extension, settings for remote management feature made in NEC ESMPRO Agent Extension is also cleared by executing Clear BMC Configuration.
Page 121 Disabled When this option is set to [Disabled], the results of POST execution are displayed [Enabled] instead of the NEC logo after the power is turned on. If [BIOS Redirection Port] is enabled, this option is shown as [Unavailable] and inaccessible.
Page 122 4-34 Configuring Your Server Option Parameters Description − CD/DVD ROM Drive BBS Specify the boot priority for each BBS. Priorities Floppy Drive BBS Priorities − − Hard Drive BBS Priorities − Network Drive BBS Priorities ]: Factory-set When BIOS detects a bootable device, it displays the information on the device for the relevant item.
Page 123: Discard Changes And Exit
Configuring Your Server 4-35 Save & Exit When the cursor is moved to the [Save & Exit] position, the Save & Exit menu is displayed. Each option in this menu is described below. IMPORTANT: The factory settings and default values differ depending on the model.
Page 124: Save Changes
4-36 Configuring Your Server Save Changes Select this item to save the newly selected settings in the CMOS memory. When [Save Changes] is selected, a confirmation screen is displayed. If you select [Yes] on this screen, the newly selected settings are saved to the CMOS memory. Discard Changes Select this item to restore the settings from before the settings were changed this time before saving.
Page 125: Configuring Motherboard Jumpers
Configuring Your Server 4-37 CONFIGURING MOTHERBOARD JUMPERS With the pre-installed SETUP utility, you can set a password to protect the data stored in the server against access from unauthorized users. When you forget the password, however, you might have to remove it as described below.
Page 126 4-38 Configuring Your Server The following describe the clearing procedure. WARNING Observe the following instructions to use the server safely. Failure to follow these instructions may result in death or serious personal injury. See pages 1-4 to 1-11 for details. Do not disassemble, repair, or alter the server.
Page 127: Interrupt Lines
Configuring Your Server 4-39 Removing Password Move the jumper switch to the password removal position in the same way as in steps 1 to 5 of "Clearing CMOS Memory". Reassemble the server, and press the POWER switch to turn on the server. Press F2 during POST to run the BIOS Setup utility, set the password again, and select [Save Changes and Exit].
Page 128: Chapter 5 Installing The Operating System With Express Setup
Chapter 5 Installing the Operating System with Express Setup This section describes information on using Express Setup to install and configure the following operating systems to the server. Microsoft® Windows Server® 2008 R2 Standard / Microsoft® Windows Server® 2008 R2 Enterprise Microsoft®...
Page 129: About Express Setup
If you want to use the drivers located on the "OEM-Disk for Mass Storage Device" that ships with optional boards, a parameters file is mandatory. You can create a parameters file in advance using "Parameter File Creator" included in NEC EXPRESSBUILDER.
Page 130: Windows Server 2008 R2
Confirm the BIOS settings described in Chapter 4 before installing Windows Server 2008 R2. Service Pack Which EXPRESSBUILDER Supports The NEC EXPRESSBUILDER DVD-ROM attached to the server supports following combination of the OS installation media and Service Pack. Windows Server 2008 R2...
Page 131 5-4 Installing the Operating System with Express Setup Supported Mass Storage Controllers The NEC EXPRESSBUILDER DVD-ROM attached to your system supports the following mass storage controllers for installation. Controllers supporting installation of OS with Express Setup – N8103-129 RAID controller (256MB, RAID 0/1)* –...
Page 132 Installing the Operating System with Express Setup 5-5 About Removable Media Do not set removable media, such as DAT and LTO, into the device mounted on this computer during the Windows installation. Connecting Hard Disk Drive Do not connect the other hard disk drives except the drive that you want to create the Windows system drive.
Page 133 5-6 Installing the Operating System with Express Setup About the System Partition Size When the system is Windows Server 2008 R2 Required partition size = size required to install OS + paging file size + dump file size + application size Size required to install OS = 8,000MB (Full Installation) = 3,500MB (Server Core Installation)
Page 134 Installing the Operating System with Express Setup 5-7 NOTE: When new partition is created, initial 100MB is assigned as boot partition by Windows OS. Example: If you make a partition of 40,960MB (40GB), usable space will be 40,960MB – 100MB = 40,860MB. The partition size required for a system with an installed memory size of 1GB (1,024MB) and a full installation of the operating system: 8,000MB + (1,024MB * 1.5) + (1,024MB + 300MB) + application size...
Page 135: Flow Of Setup
5-8 Installing the Operating System with Express Setup Flow of Setup Loading parameters (Step 2) Skip Next Select the operating system (Step 3) Next RAID configuration (Step 4) Next Windows Confirm Setting / Input (Steps 5 to 10) Next Save parameters (Step 11) Next Start Express Setup (Step 12) Perform...
Page 136: Installing The Windows Server 2008 R2
Insert the NEC EXPRESSBUILDER DVD-ROM into the optical disk drive of the server. Press the RESET switch or press Ctrl, Alt, and Delete to reboot from the NEC EXPRESSBUILDER. (You may also turn off and then on again to reboot the server.) The system will boot from the DVD and NEC EXPRESSBUILDER starts.
Page 137 5-10 Installing the Operating System with Express Setup When the Software License Agreement screen of Windows PE appears, click [Yes]. Select [Perform the Express setup] from the Top Menu, click [Next].
Page 138 Installing the Operating System with Express Setup 5-11 [Load parameters] steps are displayed. [Do not load parameters] (1) Select [Do not load parameters]. (2) Click [Next]. IMPORTANT: The setup using a parameter file saved in the Flash FDD is not supported. NOTE: If a floppy disk drive is not connected, select this item.
Page 139 5-12 Installing the Operating System with Express Setup Select the installing Operating System. Select [Install the Windows (64bit editions)] from the menu, click [Next]. Enter the setting of a logical drive. [Enter RAID settings] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next].
Page 140 If the process is not finished normally, the driver may not be stored in the EXPRESSBUILDER. Refer to "Optional Board Supported by NEC EXPRESSBUILDER" described earlier in this chapter. Specify the installing medium and the Windows system partition. [Specify medium / Partition] steps are displayed. Confirm the parameters, modify if...
Page 141 5-14 Installing the Operating System with Express Setup IMPORTANT: About partition size – Specify the partition size larger than required minimum size for OS installation. – Do not specify larger partition size than the capacity of connected hard disk drive. –...
Page 142 Installing the Operating System with Express Setup 5-15 Enter the user information. [Enter basic parameters] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next]. IMPORTANT: Computer name and Administrator password that satisfy the next condition, are required. –...
Page 143 5-16 Installing the Operating System with Express Setup Enter the setting of the network protocol. [Enter Network Protocol] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next]. Enter the domain or workgroup name to be used. [Enter domain account] steps are displayed.
Page 144 Installing the Operating System with Express Setup 5-17 Select the installing components. [Select Windows components] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next]. <Full Installation> <Server Core Installation>...
Page 145 5-18 Installing the Operating System with Express Setup Select the installing applications. [Select applications] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next]. Save the parameters. [Save parameters] steps are displayed. If you want to save the parameters , set the free formatted floppy disk. Select [Save parameters], enter the file path of the parameters files into the text box and click [Next].
Page 146 Installing the Operating System with Express Setup 5-19 The Express Setup will start when you click [Perform] in [Start Express setup] step. Remove NEC EXPRESSBUILDER DVD-ROM from the optical disk drive according to the message. If you proceed the setup by using setup parameter file, remove the floppy disk from the floppy disk drive.
Page 147 5-20 Installing the Operating System with Express Setup [Agree Software License Agreement] screen appears. (Full Installation only) Read the license terms carefully. If you agree, select I accept the license terms, and then click [Next]. When the following message appears, press Ctrl + Alt + Del. Log on to the system.
Page 148 Installing the Operating System with Express Setup 5-21 <Server Core Installation> In the following screen, enter your password into "Password", and click Hereinafter, proceed operations according to the message. Now the Setup using Express Setup has completed. After Express Setup has completed, be sure to execute the tasks described in "Installing and Setting Device Drivers".
Page 149: Installing And Setting Device Drivers
5-22 Installing the Operating System with Express Setup Installing and Setting Device Drivers Follow these steps to install and configure the device drivers. LAN Driver and PROSet The LAN driver and PROSet have been installed automatically while your system was being updated in the previous section.
Page 150: Lan Driver Setting
Installing the Operating System with Express Setup 5-23 LAN Driver Setting Link Speed LAN drivers will be installed automatically, but the link speed and Duplex mode need to be specified manually. Open the [Device Manager]. Double-click [(Network Adapter Name)] in the list. Click the [Link Speed] and specify the [Speed &...
Page 151: Setup Team
5-24 Installing the Operating System with Express Setup Setup Team Adapter Fault Tolerance (AFT) is a feature that creates a group containing more than one adapter and automatically converts the process of the working adapter to the other adapter in the group when any trouble occurred on that adapter.
Page 152 Installing the Operating System with Express Setup 5-25 Create Team Open the [Device Manager]. Open [Network adapters] → [Intel(R) xxx] properties. Click [Teaming] tab and check the [Team this adapter with other adapters] check box. Click [New Team]. Fill the name of the team in [Specify a name for the team] and click [Next]. Include the adapter to the team and click [Next].
Page 153 5-26 Installing the Operating System with Express Setup NOTE: Adapter priority config can be confirmed by the following procedure: 1. Click [TEAM: "Team name"] from [Device manager]→[Network adapters]. 2. Click [Settings] and confirm Adapters in team list. Click [Test Switch] → [Run test] to confirm the adapter team is properly setup. Confirm the result in [Test results] Restart the system.
Page 154 The drivers for LAN Board Driver (N8104-121/122/125A/126) are automatically installed by Windows Plug-and-Play. You do not need to install them manually. Graphics Accelerator Driver If you use standard graphics accelerator drivers, update your system with NEC EXPRESSBUILDER DVD-ROM attached to your system. Standard graphics accelerator drivers will be installed automatically.
Page 155: Setting For Solving Problems
5-28 Installing the Operating System with Express Setup Setting for Solving Problems Setup your computer in advance so that it can recover from any trouble precisely and as soon as possible when it should occur. For more information, refer to Page 5-88. BitLocker For BitLocker, hotfix is provided by Microsoft.
Page 156: Windows Server 2008
The setting of SNP function may affect the system performance, so please refer to the attention of SNP detail in the following site before setting it. http://www.nec.com/global/prod/express/ Refer to the public information of SNP function when KB967224 is not applied. Notes are described about KB967224.
Page 157 – OS installation media (No Service Pack) + Service Pack 2 – OS installation media (No Service Pack) Supported Mass Storage Controllers The NEC EXPRESSBUILDER DVD-ROM attached to your system supports the following mass storage controllers for installation. Controllers supporting installation of OS with Express Setup –...
Page 158 Installing the Operating System with Express Setup 5-31 Installing on the Mirrored Volume When re-installing the OS to a hard disk drive which has been upgraded to Dynamic Disk, only the simple dynamic volume is available for installation. If you want to install the OS on a volume that is mirrored using Disk Management, invalidate the mirroring and reset to the basic disk before the installation, and validate the mirroring again after the installation.
Page 159 5-32 Installing the Operating System with Express Setup About the System Partition Size The system partition size can be calculated from the following formula. When the system is Windows Server 2008 64-bit (x64) Edition: Required partition size = Size required to install OS + paging file size + dump file size + application size Size required to install OS = 11,600MB (Full Installation) 12,300MB (Full Installation with Service Pack 2)
Page 160 Installing the Operating System with Express Setup 5-33 Example: The partition size required for a system with an installed memory size of 1GB (1,024MB) and a full installation of the operating system: 11,600MB + (1,024MB * 1.5) + (1,024MB + 300MB) + application size = 14,460MB + application size.
Page 161 5-34 Installing the Operating System with Express Setup When the system is Windows Server 2008 32-bit (x86) Edition Required partition size = Size required to install OS + paging file size + dump file size + application size Size required to install OS = 6,300MB (Full Installation) 9,300MB (Full Installation with Service Pack 2) 9,400MB (Full Installation + Service Pack 2)
Page 162 Installing the Operating System with Express Setup 5-35 Example: The partition size required for a system with an installed memory size of 1GB (1,024MB) and a full installation of the operating system: 6,300MB + (1,024MB * 1.5) + 1,024MB + 300MB + application size = 9,160MB + application size.
Page 163: Flow Of Setup
5-36 Installing the Operating System with Express Setup Flow of Setup Loading parameters (Step 2) Skip Next Select the operating system (Step 3) Next RAID configuration (Step 4) Next Windows Confirm Setting / Input (Steps 5 to 10) Next Save parameters (Step 11) Next Start Express Setup (Step 12) Perform...
Page 164: Installing The Windows Server 2008
Insert the NEC EXPRESSBUILDER DVD-ROM into the optical disk drive of the server. Press the RESET switch or press Ctrl, Alt, and Delete to reboot from the NEC EXPRESSBUILDER. (You may also turn off and then on again to reboot the server.) The system will boot from the DVD and NEC EXPRESSBUILDER starts.
Page 165 5-38 Installing the Operating System with Express Setup Select [English] from the Select Language, click [OK]. When the Software License Agreement screen of Windows PE appears, click [Yes]. Select [Perform the Express setup] from the Top Menu, click [Next].
Page 166 Installing the Operating System with Express Setup 5-39 [Load parameters] steps are displayed. [Do not load parameters] (1) Select [Do not load parameters]. (2) Click [Next]. IMPORTANT: The setup using a parameter file saved in the Flash FDD is not supported. NOTE: If a floppy disk drive is not connected, select this item.
Page 167 5-40 Installing the Operating System with Express Setup Select the installing Operating System. Select [Install the Windows (32bit editions)] or [Install the Windows (64bit editions)] from the menu, click [Next]. Enter the setting of a logical drive. [Enter RAID settings] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next].
Page 168 If the process is not finished normally, the driver may not be stored in the EXPRESSBUILDER. Refer to "Optional Board Supported by NEC EXPRESSBUILDER" described earlier in this chapter. Specify the installing medium and the Windows system partition. [Specify medium / Partition] steps are displayed. Confirm the parameters, modify if...
Page 169 5-42 Installing the Operating System with Express Setup IMPORTANT: About partition size – Specify the partition size larger than required minimum size for OS installation. – Do not specify larger partition size than the capacity of connected hard disk drive. –...
Page 170 Installing the Operating System with Express Setup 5-43 Enter the user information. [Enter basic parameters] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next]. IMPORTANT: Computer name and Administrator password that satisfy the next condition, are required. –...
Page 171 5-44 Installing the Operating System with Express Setup Enter the setting of the network protocol. [Enter Network Protocol] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next]. Enter the domain or workgroup name to be used. [Enter domain account] steps are displayed.
Page 172 Installing the Operating System with Express Setup 5-45 Select the installing components. [Select Windows components] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next]. <Full Installation> <ServerCore Installation>...
Page 173 5-46 Installing the Operating System with Express Setup Select the installing applications. [Select applications] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next]. Save the parameters. [Save parameters] steps are displayed. If you want to save the parameters , set the free formatted floppy disk. Select [Save parameters], enter the file path of the parameters files into the text box and click [Next].
Page 174 Installing the Operating System with Express Setup 5-47 The Express Setup will start when you click [Perform] in [Start Express setup] step. Remove NEC EXPRESSBUILDER DVD-ROM from the optical disk drive according to the message. If you proceed the setup by using setup parameter file, remove the floppy disk from the floppy disk drive.
Page 175 5-48 Installing the Operating System with Express Setup [Agree Software License Agreement] screen appears. Read the license terms carefully. If you agree, select I accept the license terms, and then click [Next]. When the following message appears, click [Start].
Page 176 Installing the Operating System with Express Setup 5-49 When the following message appears, press Ctrl + Alt + Del. Log on to the system. <Full Installation> When the following screen appears, enter your password into "Password", and click <Server Core Installation> When the following screen appears, click "Other User".
Page 177 5-50 Installing the Operating System with Express Setup In the following screen, enter "Administrator" into [UserName], your password into "Password", and click Hereinafter, proceed operations according to the message. Now the Setup using Express Setup has completed. After Express Setup has completed, be sure to execute the tasks described in "Installing and Setting Device Drivers".
Page 178: Installing And Setting Device Drivers
Installing the Operating System with Express Setup 5-51 Installing and Setting Device Drivers Follow these steps to install and configure the device drivers. LAN Driver and PROSet The LAN driver and PROSet have been installed automatically while your system was being updated in the previous section.
Page 179 5-52 Installing the Operating System with Express Setup Select [Yes]. The uninstallation starts automatically. When [InstallShield Wizard Completed] appears. Click [Finish]. Restart the system. For a server running a Server Core installation Note down the current settings (e.g. IP addresses) of the standard and optional adapters teamed for network redundancy before uninstalling LAN driver.
Page 180 Installing the Operating System with Express Setup 5-53 LAN Driver Setting Link Speed LAN drivers will be installed automatically, but the link speed and Duplex mode need to be specified manually. Open the [Device Manager]. Double-click [(Network Adapter Name)] in the list. Click the [Link Speed] and specify the [Speed &...
Page 181 5-54 Installing the Operating System with Express Setup IMPORTANT: WOL do not work by DirectedPacket (* 1) on shutdown state even "Wake On Directed Packet" is "ON". (WOL work by DirectedPacket on sleep and hibernate state.) *1 The packet which includes ethernet address of adapter in Ethernet Header or the Packet including the IP address assigned by IP Header to adapter.
Page 182 Installing the Operating System with Express Setup 5-55 Setup Team Adapter Fault Tolerance (AFT) is a feature that creates a group containing more than one adapter and automatically converts the process of the working adapter to the other adapter in the group when any trouble occurred on that adapter.
Page 183 5-56 Installing the Operating System with Express Setup Create Team Open the [Device Manager]. Open [Network adapters] → [Intel(R) xxx] properties. Click [Teaming] tab and check the [Team this adapter with other adapters] check box. Click [New Team]. Fill the name of the team in [Specify a name for the team] and click [Next]. Include the adapter to the team and click [Next].
Page 184 Installing the Operating System with Express Setup 5-57 Remove Team Open the [Device Manager]. Click [Network adapters], and open [TEAM: "Team name"] properties. Click [Setting] tab. Click [Remove Team] button. Click [Yes] to the message. Confirm [TEAM: "Team name"] adapter is not existing in [Network adapters] tree and restart the system.
Page 185 The drivers for other LAN Boards are automatically installed by Windows Plug-and-Play. You do not need to install them manually. Graphics Accelerator Driver If you use standard graphics accelerator drivers, update your system with NEC EXPRESSBUILDER DVD-ROM attached to your system. Standard graphics accelerator drivers will be installed automatically.
Page 186: The Procedure To Set Pae Option
Installing the Operating System with Express Setup 5-59 The procedure to set PAE option If your 32-bit system has a memory capacity in excess of 4GB, setting PAE option will enable the system to be installed with over 4GB of memory. IMPORTANT: "PAE option"...
Page 187: Windows Server 2003
5-60 Installing the Operating System with Express Setup Windows Server 2003 This section explains how to install Microsoft® Windows Server® 2003 by using the Express Setup. NOTES: Express Setup does not support the installation of Windows Server 2003 x64 Editions. If you want to install it, see Appendix F. If you install Windows Server 2003 without using Express Setup, see Appendix G.
Page 188 – OS installation media (No Service Pack) Supported Mass Storage Controllers The NEC EXPRESSBUILDER DVD-ROM attached to your system supports the following mass storage controllers for installation. NOTE: If you want to install the other boards by using a driver floppy disk ("OEM-Disk for Mass storage device"), except ones listed below,...
Page 189 5-62 Installing the Operating System with Express Setup About the Hardware Components When you install the Windows Server 2003, Express Setup requires several preparations if this computer uses the following hardware components. Installing on the Mirrored Volume If you want to install the Windows Server 2003 on the volume that is mirrored using "Disk Management", invalidate the mirroring and set back to the basic disk before the installation, and validate the mirroring again after the installation.
Page 190 Installing the Operating System with Express Setup 5-63 About the System Partition Size The system partition size can be calculated from the following formula. Required partition size = Size necessary to install the system + Paging File Size + Dump File Size + Application Size Size necessary to install the system = 3500MB (Windows Server 2003 R2) = 3500MB (Windows Server 2003 R2 with Service Pack 2)
Page 191: Installing The Service Pack
5-64 Installing the Operating System with Express Setup Dividing into the partition of the recommended size into multiple disks as written below will solve problem that it cannot be reserved in one disk. Set the "Size required for installation + Paging file size". See Chapter 5 and set that debugging information (equivalent to the dump file size) is to be written to a separate disk.
Page 192: Flow Of Setup
Installing the Operating System with Express Setup 5-65 FLOW OF SETUP This section visually describes the flow of the setup operated by Express Setup. Loading parameters (Step 2) Skip Next Select the operating system (Step 3) Next RAID configuration (Step 4) Next Windows Confirm Setting / Input (Steps 5 to 10)
Page 193: Installing Windows Server 2003
Insert the NEC EXPRESSBUILDER DVD-ROM into the optical disk drive of the server. Press the RESET switch or press Ctrl, Alt, and Delete to reboot from the NEC EXPRESSBUILDER. (You may also turn off and then on again to reboot the server.) The system will boot from the DVD-ROM and NEC EXPRESSBUILDER starts.
Page 194 Installing the Operating System with Express Setup 5-67 When the Software License Agreement screen of Windows PE appears, click [Yes]. Select [Perform the Express setup] from the Top Menu, click [Next].
Page 195 5-68 Installing the Operating System with Express Setup [Load parameters] steps are displayed. [Do not load parameters] (1) Select [Do not load parameters]. (2) Click [Next]. IMPORTANT: The setup using a parameter file saved in the Flash FDD is not supported. NOTE: If a floppy disk drive is not connected, select this item.
Page 196 You can use only the physical devices that have same model number to configure logical drive. If the process is not finished normally, the driver may not be stored in the EXPRESSBUILDER. Refer to "Optional Board Supported by NEC EXPRESSBUILDER" described earlier in this chapter.
Page 197 5-70 Installing the Operating System with Express Setup Specify the installing medium and the Windows system partition. [Specify medium / Partition] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next]. IMPORTANT: If you install Windows Server 2003 R2 and Service Pack, apply Windows Server 2003 R2 DISC 2 after Express Setup completion, and then install Service Pack by "Updating the system".
Page 198 Installing the Operating System with Express Setup 5-71 Enter the user information and client license mode. [Enter basic parameters] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next]. NOTE: Even if you do not input value into "Administrator password", "Confirm password", "...
Page 199 5-72 Installing the Operating System with Express Setup Enter the domain or workgroup name to be used. [Enter domain account] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next]. Select the installing components. [Select Windows components] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next].
Page 200 Installing the Operating System with Express Setup 5-73 Select the installing applications. [Select applications] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next]. Save the parameters. [Save parameters] steps are displayed. If you want to save the parameters , set the free formatted floppy disk. Select [Save parameters], enter the file path of the parameters files into the text box and click [Next].
Page 201 5-74 Installing the Operating System with Express Setup The Express Setup will start when you click [Perform] in [Start Express setup] step. Remove NEC EXPRESSBUILDER DVD-ROM from the optical disk drive according to the message. If you proceed the setup by using setup parameter file, remove the floppy disk from the floppy disk drive.
Page 202 Installing the Operating System with Express Setup 5-75 Read the contents carefully and click [Yes] if you do agree. If you do not agree, click [No]. IMPORTANT: If you do not agree to this agreement, the setup terminates and Windows Server 2003 will not be installed. If "NetWare Gateway (and Client) Service"...
Page 203: Installing And Setting Device Drivers
PROSet is necessary to utilize these features. Follow the procedure below to install PROSet. Insert the NEC EXPRESSBUILDER DVD-ROM into the optical disk drive. If the autorun menu is displayed, close menu screen. The [Windows Explorer] dialog starts.
Page 204 Click [Next]. Choose "I accept the terms in the license agreement" and click [Next]. Click [Next]. Click [Install]. When [InstallShield Wizard Completed] window is displayed, click [Finished]. Remove the NEC EXPRESSBUILDER DVD-ROM from the optical disk drive, restart the system.
Page 205: Lan Driver Setting
5-78 Installing the Operating System with Express Setup LAN Driver Setting Link Speed LAN drivers will be installed automatically, but the link speed and Duplex mode need to be specified manually. When PROSet is not installed Open the [Device Manager] Double-click [(Network Adapter Name)] in the list.
Page 206 Installing the Operating System with Express Setup 5-79 Refer to the following procedure for WOL(Wake On LAN) setting. When PROSet is not installed Start Device Manager. Point to [Network adapters] and double click following adapter. Open the adapter [Properties]. [Intel(R) 82576 Gigabit Dual Port Server Network Connection] [Intel(R) 82576 Gigabit Dual Port Server Network Connection #2] Click [Power Management] tab and change setting in [Wake On LAN] according to the following list.
Page 207 5-80 Installing the Operating System with Express Setup When PROSet is installed Start Device Manager. Point to [Network adapters] and double click following adapter. Open the adapter [Properties]. [Intel(R) 82576 Gigabit Dual Port Server Network Connection] [Intel(R) 82576 Gigabit Dual Port Server Network Connection #2] Click [Power Management] tab and change setting in [Wake On LAN] according to the following list.
Page 208: Setup Team
Installing the Operating System with Express Setup 5-81 Setup Team Adapter Fault Tolerance (AFT) is a feature that creates a group containing more than one adapter and automatically converts the process of the working adapter to the other adapter in the group when any trouble occurred on that adapter.
Page 209 5-82 Installing the Operating System with Express Setup Create Team Open the [Device Manager]. Open [Network adapters] → [Intel(R) xxx] properties. Click [Teaming] tab and check the [Team this adapter with other adapters] check box. Click [New Team]. Fill the name of the team in [Specify a name for the team] and click [Next]. Include the adapter to the team and click [Next].
Page 210: Remove Team
Installing the Operating System with Express Setup 5-83 Remove Team Open the [Device Manager]. Click [Network adapters], and open [TEAM: "Team name"] properties. Click [Setting] tab. Click [Remove Team] button. Click [Yes] to the message. Confirm [TEAM: "Team name"] adapter is not existing in [Network adapters] tree and restart the system.
Page 211: Lan Board Driver(N8104-111/112/119/120/121/122/125A/126)
5-84 Installing the Operating System with Express Setup LAN Board Driver(N8104-111/112/119/120/121/122/125A/126) Install the driver stored in NEC EXPRESSBUILDER DVD. Installation of LAN Board Driver Start Device Manager. Click [Network adapters] and double-click [(Network Adapter Name)]. [(Network Adapter Name) Properties] appears.
Page 212: Graphics Accelerator Driver
EXPRESSBUILDER DVD-ROM attached to your system. The SCSI Controller driver will be installed automatically. Installing SAS Controller Driver (N8103-104A) If you use the SAS Controller N8103-104A, update your system with NEC EXPRESSBUILDER DVD-ROM attached to your system. The SAS Controller driver will be installed automatically.
Page 213: The Procedure To Set Pae Option
5-86 Installing the Operating System with Express Setup The procedure to set PAE option If your 32-bit system has a memory capacity in excess of 4GB, setting PAE option will enable the system to be installed with over 4GB of memory. IMPORTANT: However, the Microsoft operating system products which support /PAE switch option are limited.
Page 214: Setting For Solving Problems
Installing the Operating System with Express Setup 5-87 Setting for Solving Problems Setup your computer in advance so that it can recover from any trouble precisely and as soon as possible when it should occur. For more information, See Page 5-88.
Page 215: Setting For Solving Problems
5-88 Installing the Operating System with Express Setup SETTING FOR SOLVING PROBLEMS Setup the following issue in advance so that your computer can recover from any trouble precisely and as soon as possible when it should occur. Memory Dump (Debug Information) This section describes the procedures for collecting memory dump (debug information) in the server.
Page 216 Installing the Operating System with Express Setup 5-89 When the system is Windows Server 2008 R2 Follow the procedure below to specify. Click Start and select [Control Panel]. The [Control Panel] window appears. Click [System and Security] and then select [System]. NOTE: If [View by] is not set as [Category], start [System] from Control Panel directly.
Page 217 5-90 Installing the Operating System with Express Setup Uncheck the [Automatically manage paging file size for all drives] box, and check [Custom size]. On the [Paging file size for each drive] box, specify as follows: – A value larger than the recommended size shown in [Total paging file size for all drives] for [Initial size] –...
Page 218 Installing the Operating System with Express Setup 5-91 When the system is Windows Server 2008 Follow the procedure below to specify. Select [Control Panel] and click [System]. The [System] dialog box appears. Click [Advanced system settings]. The [System Properties] dialog box appears. Select [Advanced] tab.
Page 219 5-92 Installing the Operating System with Express Setup Click [Settings] on the [Performance] group box. The [Performance Options] window appears. Click [Advanced] tab on the [Performance Options] window. Click [Change] on the [Virtual memory] group box. Uncheck the [Automatically manage paging file size for all drives] box, and check [Custom size].
Page 220 Installing the Operating System with Express Setup 5-93 When the system is Windows Server 2003 Follow the procedure below to specify. Select [Control Panel] and click [System]. The [System Properties] dialog box appears. Select [Advanced] tab. Click [Settings] on the [Startup and Recovery] group box. IMPORTANT: Windows Server 2003 x64 Editions To specify "Complete Memory Dump"...
Page 221 5-94 Installing the Operating System with Express Setup Specify "Complete memory dump" and modify [Dump file:] in the [Write debugging information] group box. e.g. Write the debug information in D drive write the file name "MEMORY.DMP". D:\MEMORY.DMP Click [Settings] on the [Performance] group box. The [Performance Options] window appears.
Page 222: How To Create A User-Mode Process Dump File
Installing the Operating System with Express Setup 5-95 How to Create a User-mode Process Dump File When the system is Windows Server 2008 R2 "User-mode Process Dump" is the file that records information when any application error occurs. When any application error occurs, do not close the pop-up window that notifies the error, and then collect a dump using following process.
Page 223 5-96 Installing the Operating System with Express Setup When the system is Windows Server 2008 "User-mode Process Dump" is the file that records information when any application error occurs. When any application error occurs, do not close the pop-up window that notifies the error, and then collect a dump using following process.
Page 224 Installing the Operating System with Express Setup 5-97 When the system is Windows Server 2003 (Dr.Watson) Dr. Watson is a debugger for application errors. If any application error is detected, Dr. Watson diagnoses the server and logs diagnostic information (log). Follow the procedure below and specify Dr.
Page 225: Network Monitor
5-98 Installing the Operating System with Express Setup Network Monitor Utilizing Network Monitor helps you to investigate and manage with network trouble. Network Monitor Setup (Windows Server 2008 R2/Windows Server 2008) Microsoft Network Monitor allows you to examine and troubleshoot network problems. NOTE: Windows Server 2008 R2/Windows Server 2008 does not provide Network Monitor.
Page 226 Installing the Operating System with Express Setup 5-99 Network Monitor (Windows Server 2003) To utilize Network Monitor, you need to restart the system after the installation has completed, so we recommend to install Network Monitor before any network trouble may occur. Point to [Settings] from Start menu and click [Control Panel].
Page 227: Re-Installing The Operation System If Multiple Logical Drives Exist
5-100 Installing the Operating System with Express Setup Re-installing the Operation System if Multiple Logical Drives Exist Before Re-installing the Operation System Be sure to make backup copies before re-installing the operation system just in case. Re-installing the Operation System Start the clean installation following the procedure described in this manual.
Page 228 Installing the Operating System with Express Setup 5-101 Procedure for Modifying the Drive Letter Be careful that the drive letter of the system or boot volume cannot be modified with the following procedure. <Windows Server 2008 R2/Windows Server 2008> Click Start menu, right-click [Computer], and specify [Manage] to start [Server Manager]. Specify the [Storage] - [Disk Management] in the left side of the window.
Page 229: Installing Maintenance Utilities
5-102 Installing the Operating System with Express Setup INSTALLING MAINTENANCE UTILITIES Various maintenance utilities are contained in your NEC EXPRESSBUILDER DVD-ROM. See Chapter 6 for installing the utilities to your server or management workstations. UPDATING THE SYSTEM IMPORTANT: If you install Windows Server 2003 CD-ROM which contains Service Pack 2 to your system, you do not have to apply Service Pack 2 again.
Page 230: Making Backup Copies Of System Information
Without the backup data, you will not be able to recover the information. You can save the information by the following process. Connect Flash FDD or USB FDD to the USB connector. Insert the NEC EXPRESSBUILDER DVD-ROM into the optical disk drive and reboot the system. Select [Tool menu (Normal mode)].
Page 231: Installing With The Oem-Disk For Mass Storage Device
If you would like to install or re-install the OS when the system has new mass storage device not to be supported by NEC EXPRESSBUILDER, you have to set as follows. Read the manual supplied with the mass storage device before setting the server.
Page 232 Chapter 6 Installing and Using Utilities This section describes how to use the NEC EXPRESSBUILDER DVD-ROM that comes with your server and to install the utilities stored on the NEC EXPRESSBUILDER.
Page 233: Nec Expressbuilder
6-2 Installing and Using Utilities NEC EXPRESSBUILDER The NEC EXPRESSBUILDER helps you install the Operating system/the Management software or use the maintenance utilities. When you insert the NEC EXPRESSBUILDER DVD-ROM into the optical disk drive and restart the system, the following menu appears.
Page 234: Chapter 6 Installing And Using Utilities
Installing and Using Utilities 6-3 Os installation If you select this item, the Software License Agreement screen of Windows PE appears. If you click [Yes], the Top menu appears.
Page 235 6-4 Installing and Using Utilities IMPORTANT: This tool is Configuration Tool that built on Windows PE 3.0 technology. Pay attention to the automatic reboot that occurs after 72 hours from start. You can use the Express Setup (see Chapter 5) or the following functions from this menu. –...
Page 236 Installing and Using Utilities 6-5 Tool menu (Normal mode) If you select this item, the Tool menu appears. You can use the below functions for maintenance. – Maintenance Utility The Maintenance Utility is usually used by the service representative. (See Chapter 8.) –...
Page 237 6-6 Installing and Using Utilities Tool menu (Redirection mode) If you want to operate this computer via the BIOS redirection (the console-less function), select this item. NOTE: If you operate this computer via the Remote KVM function, select the "Tool menu (Normal mode)". The menu's functions are the same as the "Tool menu (Normal mode)".
Page 238: Autorun Menu
Installing and Using Utilities 6-7 Autorun Menu When the NEC EXPRESSBUILDER DVD-ROM is inserted into the optical disk drive, Windows automatically launches the menu as shown below. This menu is used to, Read the User's Guide or the other documents, Update the server system (Windows drivers), and Install the management software.
Page 239: Parameter File Creator
Also, you can install the system with the same specification as before when re-installing the system. We recommend you to create [Parameter file] to setup the servers from NEC EXPRESSBUILDER. When using a floppy disk, a USB floppy disk drive is required.
Page 240: Parameter File
IMPORTANT: Do not remove NEC EXPRESSBUILDER DVD-ROM from drive during a parameter file creation. Start the OS. Insert the NEC EXPRESSBUILDER DVD-ROM into the optical disk drive. The menu will appear. Right-click on the screen or left-click [Setup Windows]. The menu will appear.
Page 241 6-10 Installing and Using Utilities Click [Parameter File Creator]. Parameter File Creator will appear.
Page 242 Installing and Using Utilities 6-11 [Load Parameters] step is displayed. Select [Do not load parameters] from the menu, click [Next]. Select the installing Operating System. Select [Install the Windows (32bit editions)] or [Install the Windows (64bit editions)] from the menu, click [Next].
Page 243 6-12 Installing and Using Utilities Enter the setting of a logical drive. [Enter RAID setting] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next]. IMPORTANT: At "The number of the total physical devices", Parameter File Creator displays upper limit that the RAID Controller can support.
Page 244 Installing and Using Utilities 6-13 Specify the installing medium and the Windows system partition. [Specify medium / Partition] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next]. [Windows Server 2008 R2] [Windows Server 2008]...
Page 245 6-14 Installing and Using Utilities [Windows Server 2003]...
Page 246 If "Use existing partitions" is selected when you operate Windows Server 2008 R2, NEC EXPRESSBUILDER installs the Operating System to the Windows partition (The Boot partition (if it exists) and the Windows partition are deleted).
Page 247 6-16 Installing and Using Utilities Enter the user information and client license mode. [Enter basic parameters] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next]. [Windows Server 2008 R2/Windows Server 2008] [Windows Server 2003]...
Page 248 Installing and Using Utilities 6-17 IMPORTANT: Computer name and User name are required parameters. NOTE: Even if you do not input value into "Administrator password", "Confirm password", " " is displayed. Enter the setting of the network protocol. [Enter network protocol] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next].
Page 249 6-18 Installing and Using Utilities Enter the domain or workgroup name to be used. [Enter domain account] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next]. Select the installing components. [Select Windows components] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next] [Windows Server 2008 R2/Windows Server 2008]...
Page 250 Installing and Using Utilities 6-19 [Windows Server 2003] Select the installing applications. [Select applications] steps are displayed. Confirm the parameters, modify if necessary, and then click [Next]. [Windows Server 2008 R2/Windows Server 2008]...
Page 251 6-20 Installing and Using Utilities [Windows Server 2003] Save the parameters. [Save parameters] steps are displayed. If you want to save the parameters, set the free formatted floppy disk. Select [Save parameters], enter the file path of the parameters files into the text box and click [Next].
Page 252 Installing and Using Utilities 6-21 Saved to a floppy disk. Now [the floppy disk containing the parameters file] has been created. Click [Yes] to exit Parameter File Creator. NOTES: If you modify existing information file (parameter file), click "Load Parameters" at [Load Parameters] screen. Refer to help to modify information file.
Page 253: Nec Esmpro
LAN traffic. Usage threshold values can help the system administrator monitor and prevent server overloads. NEC ESMPRO Agent Extension The NEC ESMPRO Agent Extension is software for the remote management of this server. See the online documents for details on the functions and installation of the NEC ESMPRO Agent Extension.
Page 254: Nec Expressupdate Agent
Installing and Using Utilities 6-23 NEC ExpressUpdate Agent The NEC ExpressUpdate Agent enables you to control the version of the firmware and software that are installed on the server. Using the NEC ESMPRO Manager, you can download update packages automatically and install them simply without terminating the system.
Page 255: Universal Raid Utility
Universal RAID Utility. Setup with Express Setup You can install Universal RAID Utility with Express Setup contained in NEC EXPRESSBUILDER DVD-ROM. When you start the Express Setup, a dialog to specify an application appears. Select...
Page 256: Manual Setup
Linux You need to run the setup.sh in the install image of Universal RAID Utility. There is the install image of Universal RAID Utility in the following directory of NEC EXPRESSBUILDER. /BBB/lnx/pp/uraidutl The part of BBB is BBB of the medium number (5.AA-BBB.CC) of NEC EXPRESSBUILDER.
Page 257: Creating Logical Drive Of Raid 6
6-26 Installing and Using Utilities Creating Logical Drive of RAID 6 You must use four or larger Physical Devices for creating the Logical Drive of RAID 6 by Universal RAID Utility. If you want to create the Logical Drive from three Physical Devices, you need to use WebBIOS.
Page 258: Nec Product Info Collection Utility
Installing and Using Utilities 6-27 NEC PRODUCT INFO COLLECTION UTILITY The NEC Product Info Collection Utility is used to collect various system configuration and log information for maintenance or troubleshooting purpose of the server. This utility can be installed from NEC EXPRESSBUILDER DVD-ROM.
Page 259: Using Utility
6-28 Installing and Using Utilities Using Utility Execute \stdclct\collect.exe in the installation folder of this utility. The log folder is made in the above-mentioned folder, and various information on this device is stored in the data compressed file (zip form). Uninstallation Except for Server Core Choose [Add or Remove Programs] - [Product Info Collection Utility (Vx.x.x)] from the Control...
Page 260: Chapter 7 Maintenance
MAKING BACKUP COPIES NEC recommends you make backup copies of your valuable data stored in hard disk drives of the server on a regular basis. For backup storage devices suitable for the server and backup tools, consult with your service representative.
Page 261: Cleaning
7-2 Maintenance CLEANING Clean the server on a regular basis to keep the server in a good shape. WARNING Observe the following instructions to use the server safely. Failure to follow these instructions may result in death or serious personal injury. See pages 1-4 to 1-11 for details.
Page 262: Cleaning The Interior
Maintenance 7-3 Cleaning the Interior One of the most important items in a good maintenance program is regular and thorough cleaning of the interior of the server, especially around the mother board. Dust buildup inside the server can lead to several problems. As dust acts as a thermal insulator, a buildup can prevent proper system cooling.
Page 263: Cleaning The Keyboard/Mouse
7-4 Maintenance Cleaning the Keyboard/Mouse Make sure that the server and peripheral devices are all off-powered (the POWER/SLEEP lamp goes off), and then wipe the keyboard surface with a dry cloth. The mouse does not work normally if its optical sensor is stained. Wipe the optical sensor with a dry cloth.
Page 264: Cleaning Disc
Maintenance 7-5 Cleaning Disc A dusty disc or dust-accumulated tray causes the device to fail to read data correctly. Follow the procedure below to clean the tray and disc regularly: Make sure that the server is powered (the POWER/SLEEP LED is lit). Press the CD tray Open/Close button on the front of the optical disk drive.
Page 265: System Diagnostics
7-6 Maintenance SYSTEM DIAGNOSTICS The System Diagnostics runs several tests on the server. Select [Tool menu] - [Test and diagnostics] in the NEC EXPRESSBUILDER to diagnose the system. Test Items The following items are tested in system diagnostics. Memory CPU cache memory...
Page 266: Startup And Exit Of System Diagnostics
Disconnect all the LAN cables from the server. Plug the power cord and power on the server. Use the NEC EXPRESSBUILDER DVD-ROM to start the system. Select [Tool menu (Normal mode)] when local console of the server is used for, or select [Tool menu (Redirection mode)] when remote console is used for.
Page 267 7-8 Maintenance Select [Test and diagnostics]. Select [End-User Mode] and the system diagnostics starts. The diagnostics will be completed in approximately three minutes. When the diagnostics is completed, the screen of the display changes as shown below: Diagnostics tool title Test window title TeDoLi (TEst &...
Page 268 Select <Reboot> in the [Enduser Menu] above. The server restarts and the system is started from the NEC EXPRESSBUILDER. Exit the NEC EXPRESSBUILDER, and remove the DVD from the optical disk drive. Power off the server and unplug the power cord from the receptacle.
Page 269: Notes On Using Power Control Feature
Refer to the User's Guide of EXPRESSSCOPE Engine 2 or Online Help of NEC ESMPRO Manager for how to enable this feature.
Page 270 Maintenance 7-11 Notes on Using Windows Server 2008 The following event will be logged in Event Viewer if power control feature is used on Windows Server 2008. However, it is not the problem in operating the system, the event is logged because the P-State is controlled by the server side.
Page 271: Relocating/Storing The Server
7-12 Maintenance RELOCATING/STORING THE SERVER Follow the procedure below to relocate or store the server: WARNING Observe the following instructions to use the server safely. Failure to follow these instructions may result in death or serious personal injury. See pages 1-4 to 1-11 for details.
Page 272 Maintenance 7-13 Take a media out of the server, if any. Power off the server (the POWER/SLEEP lamp goes off). Unplug the power cord of the server from a power outlet. Remove all the cables from the server. Hold the server by its bottom to carry the server. IMPORTANT: Do not hold the front mask to lift the server.
Page 273 7-14 Maintenance (This page is intentionally left blank.)
Page 274: Chapter 8 Troubleshooting
Chapter 8 Troubleshooting If your server does not operate as expected, read this chapter before assuming a failure. NOTE: For provision against an unexpected failure, it is recommended to install the maintenance utility, NEC ESMPRO, to the server and client computers.
Page 275: System Viewers
Monitor the occurrence of fault by using NEC ESMPRO Manager during the system operation. Especially take note on whether any alert is reported to NEC ESMPRO Manager on the management PC. Check whether any alert is reported in NEC ESMPRO Manager.
Page 276: Status Indicators
The table below explains the STATUS LED indication, the meanings, and the procedures. NOTES: If NEC ESMPRO is installed, you can confirm the cause of a failure by referring to the error log. If shutdown processing can be performed via the operating system when you want to restart the system after turning the power off, restart the system by performing shutdown processing.
Page 277: Troubleshooting
8-4 Troubleshooting STATUS LED Description Procedure indication On (green) The server is operating normally. – Flashing The server is operating with the Identify the device in degraded state by (green) memory in degraded state. using the BIOS setup utility "SETUP," and replace it as soon as possible.
Page 278: Act Led ( )
Troubleshooting 8-5 ACT LED ( The ACT LED is green while the server is connected to the LAN. The LED flashes while the server is accessed via the LAN (during transmission/reception of packets). The number next to the icon indicates the network port number on the rear panel of the server. DISK ACCESS LED ( ) The DISK ACCESS LED indicates the status of the hard disk drive mounted in the hard disk drive bay.
Page 279: Hard Disk Drive Led
8-6 Troubleshooting Hard Disk Drive LED The disk LED located on the drive carrier indicates the following depending on the status: Disk LED Disk LED 3.5-inch hard disk drive 2.5-inch hard disk drive Flashing (green) The LED indicates that the hard disk drive is being accessed. On (amber) The LED indicates a failure of a hard disk drive mounted in the RAID system.
Page 280 Troubleshooting 8-7 IMPORTANT: If the server is turned off during rebuild processing, the processing is stopped. Restart the server, mount the new hard disk drive in hot swap mode, and then perform rebuild processing again. Observe the following notes on using the auto-rebuild function. Do not turn the power off or reboot the system during rebuild processing.
Page 281: Lan Connector Leds
8-8 Troubleshooting LAN Connector LEDs There are two LEDs for each of the two LAN ports (connectors) on the rear panel. SPEED LINK/ACT SPEED LINK/ACT SPEED LINK/ACT Management Data transmission port ports LINK/ACT LEDs Each LINK/ACT LED indicates the status of the standard network port of the server. While power is supplied to the server and HUB and the connection is correct, the LED is on (green).
Page 282: Ac Power Leds
Troubleshooting 8-9 AC POWER LEDs There is an AC POWER LED for the power supply unit on the rear. AC inlet Power supply AC POWER LED slot 2 Power supply slot 1 The LED turns green and flashes when the power supply unit receives AC power from the power cord, which is connected to the AC inlet.
Page 283: Error Messages
8-10 Troubleshooting ERROR MESSAGES If an error occurs in the server, an error message appears on the display unit connected to the server. POST Error Messages When POST detects an error, it displays an error message on the display unit screen. In addition, depending on the error contents, the computer might beep to report that an error occurred.
Page 284 Troubleshooting 8-11 Error message after power-on Displayed Error Message Description Recommended Action 8001 Real time clock error Real-time clock error Start up the BIOS setup utility, and then specify the 8002 Check date and time The real-time clock time correct date and time. If the settings setting is incorrect.
Page 285 8-12 Troubleshooting Displayed Error Message Description Recommended Action 8808 DXE_FLASH_UPDATE_FA The Flash ROM was not written Contact your service ILED to correctly. representative. 8830 PEI_RECOVERY_NO_ The Flash ROM was not CAPSULE recovered correctly. 8831 PEI_RECOVERY_PPI_ NOT_FOUND 8832 PEI_RECOVERY_FAILED PEI_CPU_NO_MICROCO An unsupported CPU was 9000 detected.
Page 286 Troubleshooting 8-13 Displayed Error Message Description Recommended Action AE01 CPU1_DIMM1 has been A memory error was detected. Contact your service disabled. representative. CPU1_DIMM1 has been disabled. CPU1_DIMM2 has been A memory error was detected. AE02 disabled. CPU1_DIMM2 has been disabled. AE03 CPU1_DIMM3 has been A memory error was detected.
Page 287 8-14 Troubleshooting Displayed Error Message Description Recommended Action AE83 CPU1_DIMM3 with error CPU1_DIMM3 was disabled, Contact your service enabled. but, because all memory is representative. currently disabled, this DIMM was forcibly enabled. CPU2_DIMM1 with error CPU2_DIMM1 was disabled, AE87 enabled. but, because all memory is currently disabled, this DIMM was forcibly enabled.
Page 288 Troubleshooting 8-15 Displayed Error Message Description Recommended Action C021 System Voltage out of the A system voltage abnormality Contact your service range. was detected. representative. C040 SROM data read error SROM data reading error C041 SROM data checksm bad SROM data checksum error C060 SMBus device Error An error was detected for the...
Page 289 8-16 Troubleshooting Displayed Error Message Description Recommended Action C106 BMC set in progress The BMC check was interrupted. Turn off the power, and then restart the server. monitoring timeout. If this does not resolve C107 BMC command access BMC command access failed. the problem, contact failed.
Page 290 Troubleshooting 8-17 Displayed Error Message Description Recommended Action C111 BMC SDR Repository Failure of the SROM for storing Turn off the power, and sensor data record information then restart the server. failure. If this does not resolve C112 BMC SEL device failure. BMC device (chip) failure the problem, contact C113...
Page 291: Messages Displayed By Raid Controller During Post
8-18 Troubleshooting Messages displayed by RAID Controller during POST On-screen message Action Memory/battery problems were detected. Contact your service representative. The adapter has recovered, but cached data was lost. Press any key to continue, or 'C' to load the configuration utility. Firmware version inconsistency was Contact your service representative.
Page 292 Troubleshooting 8-19 On-screen message Action Your VDs that are configured for write-back <When battery is not used> are temporarily running in write-through Ignore this message. mode. This is caused by the battery being charged, <When battery is used> missing, or bad. Run WebBIOS or Universal RAID Utility to check if Please allow battery to charge for 24 hours battery is detected.
Page 293 8-20 Troubleshooting On-screen message Action The cache contains dirty data, but some Check if cable, hard disk drives, and upgrade kit are VDs are missing or will go offline, so the connected properly. If the same error persists, cached data can not be written to disk. If contact your service representative.
Page 294 Troubleshooting 8-21 On-screen message Action Single-bit overflow ECC errors were Contact your service representative to replace the detected during the previous boot of the RAID controller. controller. DIMM on the controller needs replacement. If you continue, data corruption can occur. Press 'X' to continue or else power off the system and replace the DIMM module and reboot.
Page 295: Beep Codes
8-22 Troubleshooting Beep Codes If an error occurs during the POST, the server beeps, indicating the type of error. Each number indicates the number of short beeps, and a hyphen indicates a pause. For example, the beep interval 1-3-3-1 indicates 1 beep, a pause, 3 beeps, a pause, 3 beeps, a pause, and 1 beep, which indicates that an error occurred while checking the memory capacity.
Page 296: Error Messages On Virtual Lcd
Troubleshooting 8-23 Error messages on virtual LCD NEC EXPRESSSCOPE Engine 2 (Remote Management Controller), which is on your server board, allows you to monitor the server status from a Web browser running on a client PC via a network. The virtual LCD (16 digits x 2 lines) in the "Host Information" area displays the POST codes and status message.
Page 297 8-24 Troubleshooting Messages displayed on bottom line (BMC messages) On-screen message Description Action Proc1 VccpAlm XX A voltage abnormality was Contact your service detected. representative. Proc2 VccpAlm XX XX = 09: Upper limit abnormality Proc1PVtt Alm XX XX = 02: Lower limit abnormality Proc2PVtt Alm XX Proc1 1.5v Alm XX A voltage abnormality at the...
Page 298 Troubleshooting 8-25 On-screen message Description Action Proc1 T-Trip The power was forcibly turned off Contact your service due to a CPU1 temperature representative. abnormality. Proc2 T-Trip The power was forcibly turned off due to a CPU2 temperature abnormality. ChipSet T-Trip The power was forcibly turned off due to a chip set temperature abnormality.
Page 299: Solving Problems
If the server still fails to operate successfully after solving your problem, take a note on the on-screen message and contact your service representative. Problems with NEC Express Server No screen display appears and beep occurs: Is the DIMM board installed securely? →...
Page 300 Troubleshooting 8-27 POST fails to complete: Is the DIMM board installed? → Check the installation location of DIMMs (see Chapter 9). Is the memory size large? → The memory check may take a few seconds if the memory size is large. Wait for a while.
Page 301 8-28 Troubleshooting The keyboard or mouse fails to operate: Is the cable properly connected? → Make sure that the cable is connected to the correct connector on the rear of the server. → The keyboard or mouse does not operate if it is connected when the server is powered (not applicable to USB devices).
Page 302 Fail to access the (internal or external) SCSI devices: Is the SCSI device applicable to the server? → Operation of any SCSI device that is not authorized by NEC is not guaranteed. Is the cable connection changed? → See Chapter 10 for cable connection.
Page 303 8-30 Troubleshooting Event logs in using Intel Network adapter teaming Event Type: Warning Event Source: iANSMiniport Event Category: None Event ID: Description: Adapter link down:Intel(R) ---- Event Type: Warning Event Source: iANSMiniport Event Category: None Event ID: Description: Intel(R) ---- has been deactivated from the team. Event Type: Error Event Source:...
Page 304: Problems With Windows
Troubleshooting 8-31 Problems with Windows The following warnings are logged when you start Windows Server 2008 R2: Event ID: Source: e1qexpress Level: Warning Description: Intel(R) 82576 Gigabit Dual Port Server Network ... Network link has been disconnected. → If the above event is logged when you start the system, this event does not affect system operation.
Page 305 8-32 Troubleshooting The following application event is logged when Windows Server 2008 R2 is installed: Event ID: 1534 Source: Microsoft-Windows-User Profiles Service Level: Warning Description: Profile notification of event Create for component {56EA1054-1959-467f-BE3B-A2A787C4B6EA} failed, error code is The revision level is unknown. →...
Page 306 Troubleshooting 8-33 The following warnings are logged to application event log when I import a transportable shadow-copy to another server that has a floppy disk drive while operating Windows Server 2008 R2: Event ID: 12289 Source: Level: Error Description: Volume shadow copy service error: unexpected error DeviceIoControl (\\? # 6 \usbstor#sfloppy &ven_teac&prod_fd-05pub &rev_3000 &...
Page 307 8-34 Troubleshooting Event ID: 15016 Source: Microsoft-Windows-Http Level: Error Description: Unable to initialize the security package Kerberos for server side authentication. The data field contains the error number. → These events do not affect system operation. Ignore these messages. The following application events are logged when Windows Server 2008 is installed: Event ID: Source: Microsoft-Windows-WMI...
Page 308 Troubleshooting 8-35 The following system event is logged when Windows Server 2008 is installed: Event ID: Source: VDS Dynamic Provider Description: The provider failed while storing notifications from the driver. The Virtual Disk Service should be restarted. hr=80042505 → Go to the Microsoft website: http://support.microsoft.com/kb/948275/en-us/ The following application events are logged when Windows Server 2008 is installed: Event ID:...
Page 309 R2, above-shown event log will be registered. For more details, refer to "Enabling Microsoft Windows Server 2003 R2 Hardware Management" on the following site. [NEC Express5800 Web Site] http://www.nec.co.jp/express/download/W2K3_R2 The system displays the message below and fails to log on:...
Page 310 Is a floppy disk in the floppy disk drive? → Take out the floppy disk and restart the server. Is the NEC EXPRESSBUILDER DVD-ROM in the optical disk drive? → Take out the NEC EXPRESSBUILDER DVD-ROM and restart the server.
Page 311 8-38 Troubleshooting Cannot turn the power OFF at the blue screen: → If you want to turn off the power at the blue screen, execute forced shutdown (forced shutdown: continue to press POWER/SLEEP switch for 4 seconds). The power will not be turned off if you press the switch for less than 3 seconds. The PXE boot (network boot) fails or the server is not found on the network: Is the cable connected properly? →...
Page 312 Troubleshooting 8-39 Power ON/OFF (Wake On LAN) feature does not work: → Immediately after the AC power is turned on, the Remote Power ON/OFF feature (Wake ON LAN) is disabled. Start Windows Server 2003 once, provide settings as shown below, then shutdown the system. After restart, the Remote Power On/Off feature is available unless the AC power is turned off.
Page 313: Problems With Raid System Configuration
8-40 Troubleshooting Problems with RAID System Configuration Fail to install the OS: Did you create a configuration file? → Create a configuration file by using the configuration utility. Fail to start the OS: Is RAID controller inserted firmly straight into the PCI slot? →...
Page 314 Troubleshooting 8-41 Cannot set Write-Back for cache mode: → The current cache mode of RAID controller is displayed on [Virtual Disks] - [Properties] - [Policies] - "Write". If additional battery is faulty, is not connected, or insufficiently charged, the cache mode is changed to "WThru (Write Through)" even if you specify "WBack (Write Back)".
Page 315: Problems With Nec Expressbuilder
Did you set the NEC EXPRESSBUILDER during POST and restart the server? → If you do not set the NEC EXPRESSBUILDER during POST and restart the server, an error message will appear or the OS will boot. Is BIOS configuration correct? →...
Page 316 Troubleshooting 8-43 If the creation of the OEM-Disk for Windows failed, the following message will be displayed. Confirm the message, and then try the solution described in the "Cause". Error message Cause The format went wrong. It is write-protected or The Flash FDD or the floppy disk the floppy disk may be damaged.
Page 317: Problems With Express Setup
8-44 Troubleshooting Problems with Express Setup Specified to join the Domain, but the system is installed as Workgroup: → When the setup fails to join the Domain during the installation, it will install the system as Workgroup. Open [System] in Control Panel to specify joining the Domain.
Page 318: Problems With Parameter File Creator
Troubleshooting 8-45 Problems with Parameter File Creator Fail to start Parameter File Creator: Parameter File Creator requires to run by "Microsoft® HTML Application host". → If Parameter File Creator does not start, associate the file type with "Microsoft® HTML Application host" via following process. 1) Click [Run] on Start menu.
Page 319: Problems With N8190-127/131/153/154 Fibrechannel Controller
→ It is not a problem in operating the system. To display correct controller name, run following command in the driver software NEC EXPRESSBUILDER DVD and restart the system. [Windows Server 2008 R2/Windows Server 2008 32-bit (x86) / Windows Server 2008 64-bit (x64)] <Drive Letter>:\017\win\winnt\ws2008x64\elxstor\friendlyname.exe...
Page 320: Problems With Autorun Menu
Troubleshooting 8-47 Problems with Autorun Menu Cannot read documents: Do you have Adobe Reader installed correctly in your system? → Some documents are supplied with PDF format. To read the document of PDF format, Adobe Reader is required in your system. Is the operating system Windows XP SP2 (or later)? →...
Page 321: Collecting Event Log
8-48 Troubleshooting Collecting Event Log This section describes on how to collect the log of various events that occurred on the server. IMPORTANT: If STOP error, system error, or stall occurred, follow the procedure below after restarting the system. Click [Management Tool] → [EventViewer] from the Control Panel. Select the type of the log to collect.
Page 322: Collect Configuration Information
Troubleshooting 8-49 Collect Configuration Information This section describes on how to collect the information on hardware configuration and inside specification. In order to collect information, "Diagnostic Program" is used. IMPORTANT: If STOP error, system error, or stall occurred, follow the procedure below after restarting the system. Point to [Settings] in Start menu, and click [Control Panel].
Page 323: Recovery For Windows System
8-50 Troubleshooting RECOVERY FOR Windows SYSTEM If any file necessary for running the OS is damaged, use the following procedures to recover the system. IMPORTANT: After recovering the system, see "Updating the System" in Chapter 5 and be sure to update the system. Also, you need to update all the drivers after the system update.
Page 324: Maintenance Tools
Insert the NEC EXPRESSBUILDER DVD-ROM supplied with your server into the optical disk drive of your server. Press Ctrl, Alt, and Delete to reboot the server from the NEC EXPRESSBUILDER. (You may also turn off and then on again to reboot the server.) System boots up displaying Boot selection menu.
Page 325 8-52 Troubleshooting When a local console is used, "Tool menu (Normal mode)" is selected. Moreover, "Tool menu (Redirection mode)" is selected when using it with remote console. IMPORTANT: An initial selection of the menu is "Japanese". "Japanese" starts by the automatic operation when the operation is not done for five seconds after the Language selection menu is displayed.
Page 326 Troubleshooting 8-53 When you use a remote console Each tool is selected, and it starts.
Page 327: Function Of Maintenance Tools
The Off-line Maintenance Utility is started in Maintenance Utility. The Off-line Maintenance Utility is an OS-independent maintenance program. When you are unable to start the OS-dependent NEC ESMPRO to troubleshoot a problem, the Off-line Maintenance Utility can be used. IMPORTANT: The Off-line Maintenance Utility is intended for use of your service representative.
Page 328 BIOS/FW Updating This menu allows you to update the software module such as BIOS and firmware of the server by using the update disk (3.5-inch floppy disk) that is distributed from NEC customer service representative. After restarting the system, an update program is started automatically from floppy disk, and the various BIOS and firmware programs are updated.
Page 329: Maintenance Tools With Remote Console
IMPORTANT: Do not use this feature on any other computer than the server, or on any other server obtained without the NEC EXPRESSBUILDER. Doing so may cause a failure of the server. Be sure to select [Tool menu (Redirection mode)] in [Boot selection] menu from the remote console.
Page 330 PC, and various setup parameters. Use NEC ESMPRO BMC Configuration or NEC ESMPRO Agent Extension or run "System Management" menu from NEC EXPRESSBUILDER to create a configuration file. Save the configuration file into the root directory of the floppy disk as the following file name.
Page 331: Resetting The Server
8-58 Troubleshooting RESETTING THE SERVER If the server halts before starting the OS, press and hold Ctrl and Alt and press Delete. This restarts the server. IMPORTANT: Resetting the server clears the DIMM memory and the data in process. To reset the server when it is not frozen, make sure that no processing is in progress.
Page 332: Forced Shutdown
Troubleshooting 8-59 FORCED SHUTDOWN Use this function when an OS command does not shut down the server, the POWER/SLEEP switch does not turn off the server, or resetting does not work. Press and hold the POWER/SLEEP switch on the server for at least four seconds. The power is forcibly turned off.
Page 333: Chapter 9 Upgrading Your Server
Optional devices described in this chapter may be installed or removed by any user. However, NEC does not assume any liability for damage to optional devices or the server or malfunctions of the server resulted from installation by the user. NEC recommends you ask your service representative for installing or removing any optional devices.
Page 334: Safety Notes
9-2 Upgrading Your Server SAFETY NOTES Observe the following notes to install or remove optional devices safely and properly. WARNING Observe the following instructions to use the server safely. Failure to follow these instructions may result in death or serious personal injury. See pages 1-4 to 1-11 for details.
Page 335: Anti-Static Measures
Upgrading Your Server 9-3 ANTI-STATIC MEASURES The server contains electronic components sensitive to static electricity. Avoid failures caused by static electricity when installing or removing any optional devices. Wear a wrist strap (an arm belt or anti-static glove). Wear a wrist strap on your wrist. If no wrist strap is available, touch an unpainted metal part of the cabinet before touching a component to discharge static electricity from your body.
Page 336: Preparing For Installation And Removal
9-4 Upgrading Your Server PREPARING FOR INSTALLATION AND REMOVAL Follow the procedure below to prepare for installing or removing components. Shutdown the OS. Shutdown process is not required if the hard disk drives and the additional power supply units are hot-swappable. Unlock the front bezel with the security key.
Page 337: Upgrading Your Server
Upgrading Your Server 9-5 See page 9-5 to prepare. NOTE: To confirm the device you are going to maintain, use the UID switch and the UID LED that goes on when the switch is pressed. Press the unlock buttons at the right and left sides of the front panel, and slowly pull out the server from the rack.
Page 338: Attachment And Post-Attachment Checks
9-6 Upgrading Your Server ATTACHMENT AND POST-ATTACHMENT CHECKS After adding an option or attaching a component, check the following points. Attach removed components in the same way as before. When adding or removing components, attach removed components and cables in the same way as before.
Page 339: Hard Disk Drive
For details, see the figure below. IMPORTANT: Use a hard disk drive authorized by NEC. Installing a third-party hard disk drive might cause a failure of the server as well as the hard disk drive. Purchase hard disk drives of the following models (current as of June 2010): –...
Page 340 IMPORTANT: Use a hard disk drive authorized by NEC. Installing a third-party hard disk drive might cause a failure of the server as well as the hard disk drive. Purchase hard disk drives of the following models (current as of June 2010): –...
Page 341 Upgrading Your Server 9-9 Upon shipment, the hard disk drive bays are connected to the onboard controller in the server. If using these hard disk drives for a RAID system, refer to the following. If using the optional RAID controller N8103-129/130 Use WebBIOS or the Universal RAID Utility to build, set up, or manage a RAID system.
Page 342: Installation
9-10 Upgrading Your Server Installation Take the following steps to install a hard disk drive. This procedure applies to all the hard disk drive bays. See the next section for the procedure installing a hard disk drive in the flex bay. NOTE: Any hard disk drive can be installed or removed in or from the server only by removing the front bezel.
Page 343 Upgrading Your Server 9-11 Unlock the hard disk drive handle. Firmly hold the drive carrier, and insert it into the slot. Put your fingers on the front of the drive carrier.
Page 344 9-12 Upgrading Your Server Push the drive carrier into the slot until it stops. IMPORTANT: Confirm that the handle is hooked to the frame when having inserted the hard disk drive. Be careful not to get your finger caught between the handle and tray. Slowly close the handle.
Page 345: Inch Hard Disk Drive
Upgrading Your Server 9-13 Power on the server, and run the SETUP utility. Select the [Boot] menu (described on page 4-33) to set the boot priority. When you install an additional hard disk drive, the boot priority stored in BIOS is cleared. Install the front bezel you removed in step 2.
Page 346 9-14 Upgrading Your Server Unlock the hard disk drive handle. With the handle in the fully open position, firmly hold the drive carrier and handle, and insert it into the chassis. IMPORTANT: Push the drive to check if it is firmly secured. Carefully hold the hard disk drive with both hands.
Page 347 Upgrading Your Server 9-15 When the handle begins to close by itself, slowly close the handle. The drive carrier is locked when a "click" is heard. IMPORTANT: Be careful not to get your finger caught between the handle and tray. Push the drive further to check if it is firmly secured.
Page 348: Removal
9-16 Upgrading Your Server Removal Take the following steps to remove a hard disk drive: 3.5-inch hard disk drive NOTE: If removing a failed hard disk drive, confirm the slot in which the DISK LED of the hard disk drive is amber before starting the removal.
Page 349 Upgrading Your Server 9-17 Power on the server, and run the SETUP utility. This is because, when a hard disk drive is added, the previously recorded boot order settings are cleared. Install the front bezel you removed in step 2. 2.5-inch hard disk drive IMPORTANT: Do not press the POWER switch during the...
Page 350 9-18 Upgrading Your Server Open the handle. Firmly hold the drive carrier, and pull out the hard disk drive. Do not hold the handle. If using the server with the hard disk drive removed, install the dummy tray in the vacant slot to ensure the cooling efficiency.
Page 351: Notes On Replacing Hard Disk Drives In The Raid System
Upgrading Your Server 9-19 Notes on Replacing Hard Disk Drives in the RAID System When the hard disk drives are in the RAID System, you can restore the state before an error using the auto-rebuild feature that stores the data in the old hard disk drive into a new one. The auto-rebuild feature is available for the RAID1, RAID5, RAID6, RAID10, or RAID50.
Page 352: Power Supply Unit
9-20 Upgrading Your Server POWER SUPPLY UNIT Your server contains one or two power supplies. The second power supply is optional and provides a redundant configuration that ensures continued operation of the system in the unlikely event one of the power supplies fails. Installation Take the following steps to install a power supply unit: See page 9-4 to prepare.
Page 353 Upgrading Your Server 9-21 IMPORTANT: Do not touch the terminals of the power supply unit. Contact terminals Grab the handle and securely press the power supply unit into place. The power supply unit is locked when a distinct "click" is heard.
Page 354 9-22 Upgrading Your Server Connect two power cords. Use the power cord provided with the standard power supply unit and the one provided with the system. The AC POWER LEDs flash green when the power cords are connected. If the power unit is not connected with the power cord, its AC POWER LED goes on amber.
Page 355: Replacing A Failed Power Supply Unit
Upgrading Your Server 9-23 Replacing a Failed Power Supply Unit Replace only a failed power supply unit. CAUTION Observe the following instructions to use the server safely. Failure to follow these instructions may cause a fire, personal injury, or property damage. See pages 1-4 to 1-11 for details.
Page 356 9-24 Upgrading Your Server Install the new power supply unit taking steps 3 to 7 of "Installation", and confirm that the power supply unit is installed normally. NOTE: If one of the two power supply units of the server is replaced, the AC POWER LED of the new power supply unit goes on amber until the AC power cord is connected.
Page 357: Drive Cover
Upgrading Your Server 9-25 DRIVE COVER When attaching the drive cover, make sure that the drive cover tab is securely inserted into the server frame, and slide the drive cover towards the back. Removal See page 9-4 to prepare. Pull the server out of the rack (as described on page 9-4). Slide the drive cover toward the rear of the server while pressing the lock buttons on the cover.
Page 358: Logic Cover
9-26 Upgrading Your Server LOGIC COVER Remove the logic cover when attaching or removing DIMMs, the CPU, or PCI cards, as well as when changing internal cable connections Removal See page 9-4 to prepare. Pull the server out of the rack (as described on page 9-4). Loosen the set screw on the back of the logic cover, and then slide the cover towards the back.
Page 359: Dimm
DIMM terminals or on-board parts by a bare hand or place the DIMM directly on the desk. For static notes, see page 9-3. Make sure to use a DIMM authorized by NEC. Installing a third-party DIMM might cause a failure of the DIMM as well as the server.
Page 360: Installation Order
9-28 Upgrading Your Server Installation Order Installation order depends on the number of CPUs installed. 1-CPU configuration: Install DIMMs starting from the smallest slot number. 2-CPU configuration: Alternately install DIMMs starting from the smallest slot number of each CPU. Install DIMMs starting from the largest capacity and from the smallest slot number (16GB →...
Page 361: Memory Clock
Upgrading Your Server 9-29 Memory Clock The DR3-800/1066/1333MHz memory clock frequencies are supported, but this depends on the CPU and memory configurations. Note that all bus memory clocks operate at the same clock frequency. Memory drive voltage: Low (1.35V/power-saving mode) Automatically shifts Is the onboard CPU Xeon to 1.5V operation...
Page 362: Memory Ras Feature
9-30 Upgrading Your Server Memory RAS Feature The server has RAS features including "standard memory configuration (x4 SDDC ECC memory)", a "memory mirroring feature", a "memory LockStep (x8 SDDC ECC memory) feature", and a "memory sparing feature". To use the memory mirroring or LockStep feature, see "Using the Memory RAS Features"...
Page 363: Installation
Upgrading Your Server 9-31 Installation Install a DIMM in the following procedure. IMPORTANT: The server supports DIMMs of only the low-profile type (30 mm (1.2 inches) in height). It does not support DIMMs exceeding the specified height. See page 9-4 to prepare. Pull out the server from the rack (as described on page 9-4).
Page 364 9-32 Upgrading Your Server Open levers at left and right side of the DIMM socket, and remove the dummy memory. IMPORTANT: Keep the removed dummy memory for future use. Holding the DIMM by the edges, remove it from its anti-static package. Position the DIMM above the socket.
Page 365 Upgrading Your Server 9-33 Attach the support bar. Make sure that the tab of the processor duct is inserted under the support bar. Support bar Processor duct NOTE: The support bar can spring upwards when freed, resulting in the loss of screws. Firmly hold the support bar down while removing the screws.
Page 366: Removal
Remove the DIMM using the following procedure. NOTE: To remove the failed DIMM, check the error message appearing in POST or NEC ESMPRO to identify the DIMM socket (group) in which the failed DIMM is installed. See page 9-4 to prepare.
Page 367: Using The Memory Ras Features
Upgrading Your Server 9-35 Using the Memory RAS Features The server has RAS feature including "Standard memory configuration (x4 SDDC ECC memory)", a "memory mirroring feature", a "memory sparing feature", and a "LockStep (x8 SDDC ECC memory) feature". SDDC (Single Device Data Correction) allows automatic correction of memory error (multi-bit error).
Page 368: Memory Mirroring
9-36 Upgrading Your Server Memory mirroring The memory mirroring feature writes the same data into two groups of DIMMs corresponding with each other between memory channels (channels 0 and 1) to provide data redundancy. IMPORTANT: The memory mirroring feature uses channels 0 and 1. In memory mirroring configuration, the memory channel 2 of each CPU (CPU1-DIMM3/6, CPU2-DIMM3/6) is disabled.
Page 369 Upgrading Your Server 9-37 The memory mirroring feature can be used under the following conditions: Install memory devices on two memory sockets configuring a mirror set. All the installed memory devices should have the same capacity. Run SETUP (described on page 4-2), change parameters appropriately in the [Mirror] menu selected as shown below, save the settings and exit from SETUP.
Page 370 9-38 Upgrading Your Server Memory LockStep feature (x8 SDDC) In LockStep feature, the DIMMs in two groups corresponding to two memory channels (channels 0 and 1) is multiplexed and operated in parallel to enable x8 SDDC (x8 Single Device Data Correction).
Page 371 Upgrading Your Server 9-39 The LockStep feature can be used under the following conditions: Install two DIMMs that operate in parallel in memory socket. All the installed DIMMs should have the same capacity. Run SETUP (described on page 4-2), change parameters appropriately in the menu selected as shown below, save the settings and exit from SETUP.
Page 372: Memory Sparing
9-40 Upgrading Your Server Memory sparing Memory sparing is a feature whereby channel 2 of the memory controller in each CPU is designated as a "spare" channel and the DIMMs (memories) that use that channel are put on standby so that operations can be automatically switched to a standby DIMM if a correctable error occurs in one of the DIMMs operating under the control of the memory controller, allowing processing to continue unimpeded.
Page 373 Upgrading Your Server 9-41 Observe the following when using the memory sparing feature: The capacity of the additional memory sticks (DIMMs) must the same as the capacity of the memory sticks installed in the server. Launch the SETUP utility (referring to System BIOS SETUP on page 4-2) and change the parameter below.
Page 374: Processor (Cpu)
Do not operate the system until confirming that the additionally installed CPU is in normal state. Make sure to use the CPU authorized by NEC. Installing a third-party CPU might cause a failure of the CPU as well as the server.
Page 375: Installation
Upgrading Your Server 9-43 Installation Take the following steps to install the CPU. See page 9-4 to prepare. Pull out the server from the rack (as described on page 9-4). Remove the drive cover and logic cover (as described on page 9-25). Remove the PCI riser card (as described on page 9-51).
Page 376 9-44 Upgrading Your Server Remove the four screws, and remove the CPU dummy cover. IMPORTANT: Keep the removed cover for future use. Open the socket lever by pushing the lever down and away from the socket. Lift the load plate. IMPORTANT: Do not touch the socket contacts.
Page 377 Upgrading Your Server 9-45 Remove the protective socket cover from the load plate. IMPORTANT: Do not discard the protective socket cover. Always replace the socket cover if the processor is removed from the socket. Hold a new processor with your thumb and index fingers and place it on the socket carefully as shown in the figure below.
Page 378 9-46 Upgrading Your Server Slightly press the processor on the load plate, close the load plate, and then engage the socket lever. Put the heat sink on CPU and fix the heat sink with four screws. Check the orientation of the heat sink, and then tighten the screws. Make sure that the screw aligns with the screw hole.
Page 379 Upgrading Your Server 9-47 NOTE: Be aware of direction of heat sink (see figure below). Front of the server Rear of the server CPU2 heat sing CPU1 heat sing Make sure that the heat sink is level. NOTES: If the heat sink is not level, remove it, and then install it again. The following probably causes the heat sink not to be level: –...
Page 380 9-48 Upgrading Your Server USB cable Attach the support bar. Run the USB cable through the groove in the support bar. Make sure that the tab of the processor duct is inserted under the support bar. Support bar Processor duct...
Page 381 Upgrading Your Server 9-49 NOTE: The support bar can spring upwards when freed, resulting in the loss of screws. Firmly hold the support bar down while removing the screws.
Page 382: Removal
9-50 Upgrading Your Server Removal To remove the CPU, prepare the removal referring to steps 1 and 6 in the installation procedure and do the reverse procedure of steps 15 to 8. IMPORTANT: Do not remove any CPU unless it is failed. After the operation, heat may make the cool seat at the bottom of the heat sink adhere to the CPU.
Page 383: Pci Card
Upgrading Your Server 9-51 PCI CARD On the motherboard, the server has a riser card assembly that enables installation of PCI cards and a RAID controller-dedicated slot that enables installation of a RAID controller. The riser card assembly can hold up to two full-height PCI boards, three low-profile PCI boards, and one RAID controller (for a total of six PCI boards).
Page 384 9-52 Upgrading Your Server Riser card slot (Dedicated to low-profile PCI boards) Riser card slot (Dedicated to full-height PCI boards) Slot for RAID Controller REAR FRONT Mother board...
Page 385: Notes
Upgrading Your Server 9-53 Notes Observe the following notes on installing/removing a PCI card: Do not touch the terminals of the riser cards and the leads of electronic components with your bare hand. Fingerprints and dust left on them cause the server to malfunction due to a connection failure or damage to the leads.
Page 386 9-54 Upgrading Your Server additionally installed, the boot priority is changed. After the additional installation, start the BIOS SETUP utility, select [Boot] and set the new boot priority. If a device that can be booted (PCI card, USB device, etc.) is added, the boot priority might change.
Page 387: Installation
Upgrading Your Server 9-55 Installation Take the following steps to install a PCI card on the riser card: IMPORTANT: Each riser card supports low-profile or full-height PCI cards. Before installing a PCI card, confirm that the type of the PCI card. When installing a PCI card, confirm that the card connector matches the connector of the riser card.
Page 388 9-56 Upgrading Your Server Remove the screw from the riser card, and remove the additional slot cover. Low-profile riser card Full-height side riser card NOTE: Keep the removed additional slot cover for future use. Only for the full-height, full-length type When inserting a full-height, full-length PCI card, remove the card retainer.
Page 389 Upgrading Your Server 9-57 Install the PCI board on the riser card. Align the PCI board terminal section with the riser card slot, and firmly push the PCI board until it is fully seated. Tip of the PCI board Low-profile riser card Tip of the PCI board Full-height riser card Guide rail...
Page 390 9-58 Upgrading Your Server Secure the PCI card with the screw you removed in step 5. Full-height riser card Low-profile riser card IMPORTANT: This step is to protect the terminals of the riser card from dust or fingerprints. Dust and fingerprints left on them cause the server to malfunction.
Page 391: Removal
Upgrading Your Server 9-59 After inserting the riser card, firmly press on it with your fingers to connect it. Install the components you removed previously. Verify that POST displays no error messages. If POST displays an error message, take a note on the message and see the POST error messages listed on page 4-15.
Page 392 9-60 Upgrading Your Server [Advanced] menu of the BIOS setup utility, make sure that the [PCI Slot xx ROM] parameter (where xx is the PCI slot number) under [PCI Configuration] is set to [Enabled]. IMPORTANT: When N8103-129/130 is inserted, do not switch to the hibernation or standby mode.
Page 393 Upgrading Your Server 9-61 Attach the RAID controller to the bracket that was removed from the server chassis. Use the screws removed in step 6. Screws Install the RAID controller in the server chassis, and secure it with the screws that were used to secure the bracket.
Page 394: Installing Additional Battery For Raid Controller
9-62 Upgrading Your Server Installing Additional Battery for RAID Controller Take the following steps to install an additional battery for RAID controller. See page 9-4 to prepare. Pull out the server from the rack (as described on page 9-4). Remove the logic cover (as described on page 9-25). Hold the riser card handle and bracket as shown in the figure on the right, and remove the riser card.
Page 395 Upgrading Your Server 9-63 Install the connector board provided with the additional battery to the RAID controller. Connector board Screw Secure the RAID controller to the server chassis. Remove the two screws for the battery bracket attached to the server, and then remove the bracket.
Page 396 9-64 Upgrading Your Server Use the screws that came with the additional battery to fix the battery to the bracket. Screw Connect the cable to the additional battery. Be aware of the face of the connector according to the figure below. Connect a cable to the connector with matching their markings.
Page 397 Upgrading Your Server 9-65 Use the screws that came with the additional battery to fix the battery to the bracket. Screw For a 2-5-inch model, route the cables as shown in the following figures. – When connecting to a RAID controller inserted into the dedicated slot...
Page 398 9-66 Upgrading Your Server When connecting to a RAID controller inserted into a low-profile slot When connecting to a RAID controller inserted into a full-height slot...
Page 399: Removing Additional Battery For Raid Controller
Upgrading Your Server 9-67 Connect the cable to the connector board installed on the RAID controller. Be aware of the face of the connector according to the figure below. Install the components you removed previously. Removing Additional Battery for RAID Controller Remove the additional battery for RAID controller in reverse order of the installation steps.
Page 400: Use Of Internal Hard Disk Drives In The Raid System
9-68 Upgrading Your Server USE OF INTERNAL HARD DISK DRIVES IN THE RAID SYSTEM Using the RAID controller allows you to use hard disk drives in the device bays of the server and those in the optional expansion disk cabinet in the RAID System. A RAID system can be built by using an optional RAID controller (N8103-129/130).
Page 401 Upgrading Your Server 9-69 Optional RAID Controller (N8103-129/130) At the factory, the interface cable is connected to the SATA HDD connector on the motherboard. Refer to the manual coming with optional RAID controller (N8103-129/130) for details. IMPORTANT: The RAID controller board is extremely sensitive to static electricity.
Page 402 9-70 Upgrading Your Server Observe the following when configuring a RAID system: Use the minimum number of hard disk drives required to configure the desired RAID level. These hard disk drives must have either the same capacity or the same rotational speed.
Page 403: Backup Devices
(For details, see Supported cards and slots into which they can be inserted on page 9-71.) Do not install a backup device that is not specified by NEC. Only devices that have dimensions up to a width of approximately 9 cm (3.5 inches) and a height of approximately 4 cm (1.6 inches) can...
Page 404: Installing A Scsi Interface Device
9-72 Upgrading Your Server Installing a SCSI interface device IMPORTANT: To use a device that has an SCSI interface, a separately sold optional PCI SCSI controller is required. Prepare as described on page 9-4. Pull the server out of the rack (as described on page 9-4). Remove the drive cover and logic cover (as described on pages 9-25, 9-26).
Page 405 Upgrading Your Server 9-73 Remove the front panel. IMPORTANT: Keep the removed front panel in a safe place. Insert a backup device into the device carrier. Use the screws that came with the server to fix the backup device in place. NOTE: Be sure to use the screws that came with the server.
Page 406 9-74 Upgrading Your Server Connect the interface cable and power cable to the backup device. Connect the power cable that came with the server and the separately sold SCSI cable (K410-147 (00)) to the backup device. Terminator AC power cable SCSI cable NOTE: A power cable is provided for the device bay.
Page 407: Installing A Usb Interface Device
Upgrading Your Server 9-75 Attach the removed components. Start up the SCSI BIOS utility, and then set up the SCSI device. For details, see the instruction manual that came with your backup device. Install the device driver for the connected backup device. For details, see the instruction manual that came with your backup device.
Page 408 9-76 Upgrading Your Server Remove the front panel. IMPORTANT: Keep the removed front panel in a safe place. Insert a backup device into the device carrier. Use the screws that came with the server to fix the backup device in place. NOTE: Be sure to use the screws that came with the server.
Page 409 Upgrading Your Server 9-77 Connect the interface cable and power cable to the backup device. Connect the power cable that came with the server and the separately sold USB cable (K410-194/195 (00)) to the backup device. USB cable AC power cable NOTE: A power cable is provided for the device bay.
Page 410: Removal
9-78 Upgrading Your Server Attach the removed components. IMPORTANT: If an N8151-81-internal MO (USB) or N8151-86-internal RDX (USB) is connected, the boot order might be changed. On the [Boot] menu of the BIOS setup utility, make the boot priority of the above removable devices lower than the boot disk.
Page 411: Installation
Upgrading Your Server 9-79 Installation Prepare as described on page 9-4. Pull the server out of the rack (as described on page 9-4). Remove the drive cover (as described on page 9-25). Determine the expansion slot in which to insert an additional fan. Insert the fan straight into this slot.
Page 412: Removal
9-80 Upgrading Your Server Removal To remove a backup fan, prepare as described in steps 1 to 3 of Installation, and then perform the procedure below. A fan can be replaced even while the power is on (hot swapping). CAUTION To safely use the server, observe the caution below.
Page 413 Upgrading Your Server 9-81 Change the position of the JFANSEL_1 jumper strap on the fan board. IMPORTANT: Do not change any other jumper settings. Doing so might cause a server failure or incorrect operations. 3 2 1 3 2 1 Redundant Standard configuration...
Page 414: Optical Disk Drive
You may replace the factory-installed optical disk drive with an optional DVD SuperMULTI drive. IMPORTANT: Be sure to use the optical disk drive authorized by NEC. Optical disk drive bay Installation Procedure Take the following steps to install the optical disk drive.
Page 415 Upgrading Your Server 9-83 Remove the two screws that fix the dummy cover in place, and then remove the cover. Screws Remove the screw that fixes the optical disk drive bracket cover in place, and then slide the cover in the direction of the arrow to remove it. Cover fixing screws Cover Attach the optional internal optical disk drive to the bracket, and then fix the drive in...
Page 416 9-84 Upgrading Your Server Install the drive into the server by performing steps 4 and 5 in reverse. Install the components you removed previously.
Page 417: Appendix A Specifications
Appendix A Specifications 2.5-inch HDD model Express5800/R120b-2 Diskless model Item N8100- N8100- N8100- N8100- N8100- N8100- 1644F 1645F 1646F 1647F 1648F 1649F ® ® ® ® ® ® Type Intel Intel Intel Intel Intel Intel ® ® ® ® ®...
Page 418 A-2 Specifications Express5800/R120b-2 Diskless model Item N8100- N8100- N8100- N8100- N8100- N8100- 1644F 1645F 1646F 1647F 1648F 1649F Interface Keyboard/mouse 1 port (PS/2, 1 for rear panel)/1 port (PS/2, 1 for rear panel) Analog RGB 2 ports (MINI D-Sub 15-pin, 1 for front panel, 1 for rear panel)
Page 419 Specifications A-3 3.5-inch HDD model Express5800/R120b-2 Item Diskless model N8100-1650F N8100-1651F N8100-1652F N8100-1653F ® ® ® ® ® ® ® ® Type Intel Xeon Intel Xeon Intel Xeon Intel Xeon Processor Processor Processor Processor E5503 E5506 E5620 X5640 Clock 2GHz 2.13GHz...
Page 420 A-4 Specifications Express5800/R120b-2 Item Diskless model N8100-1650F N8100-1651F N8100-1652F N8100-1653F External Excluding front bezel, 445.2 (width) x 721.2 (depth) x 86.7 (height) dimensions inner rail, and (mm) protruding parts Including front bezel, 486.5 (width) x 821.9 (depth) x 88.6 (height)
Page 421: Appendix B Other Precautions
Server Management Software The NEC EXPRESSBUILDER DVD-ROM that comes with the server contains the NEC ESMPRO utility. NEC recommends that you should install the NEC ESMPRO for effective use of the reliability enhancement features of the server. Floppy Disk The following describes use of the floppy disk.
Page 422 You can read data from a write-protected floppy disk, but you cannot save data into the floppy disk or format it. NEC recommends that you should write-protect any floppy disk containing valuable data unless you are about to save data.
Page 423 The floppy disk is a very delicate storage media. Dust or thermal changes, as well as operator's misconduct or sever failures, may cause loss of data. To avoid loss of data, NEC recommends that you should make a back-up copy of your valuable data on a regular...
Page 424: Dvd/Cd-Rom
Three-generation data management NEC recommends that you should employ three-generation data management for data storage. Three-generation data management uses three cartridge tapes: A, B, and C. You save data to tape A on the first day, tape B on the second day, tape C on the third day, tape A on the forth day, and so on.
Page 425: Keyboard
Other Precautions B-5 This enables you, for example, to use tape B to restore the data when tape C makes a read error. Also when both tapes B and C make a read error, you can restore your valuable data by using the data stored in tape A.
Page 426: Mouse
B-6 Other Precautions Mouse Like the keyboard, the mouse is a device to instruct your computer. Many OS's and application software require the mouse for operation. NOTE: Functions assigned to the mouse buttons vary depending on the software. For details, refer to the manual provided with the software.
Page 427: Appendix C Irq
Appendix C The factory-set interrupt requests are listed below. Find an appropriate one to install an optional device. Interrupt Request The factory-set IRQs are assigned as follows: Peripheral Device Peripheral Device (Controller) (Controller) System timer SM Bus − Numeric data processor −...
Page 428 C-2 IRQ (This page is intentionally left blank.)
Page 429: Appendix D Installing Windows Server 2008 R2
NOTICE Read the following notes or information before installing the Windows Server 2008 R2. Optional Board Supported by NEC EXPRESSBUILDER The NEC EXPRESSBUILDER DVD-ROM attached to your server supports the following optional boards: NOTE: If you want to install the other boards by using a driver floppy disk ("OEM-Disk for Mass storage device"), except ones listed below,...
Page 430: Service Pack Which Expressbuilder Supports
D-2 Installing Windows Server 2008 R2 Service Pack Which EXPRESSBUILDER Supports The NEC EXPRESSBUILDER DVD-ROM attached to the server supports following combination of the OS installation media and Service Pack. Windows Server 2008 R2 – OS installation media (No Service Pack) Installing Service Pack You can install the Service Pack on the server.
Page 431: About The System Partition Size
Installing Windows Server 2008 R2 D-3 About the System Partition Size The system partition size can be calculated from the following formula. When the system is Windows Server 2008 R2: Required partition size = size required to install OS + paging file size + dump file size + application size Size required to install OS = 8,000MB (Full Installation) = 3,500MB (Server Core Installation)
Page 432: D-4 Installing Windows Server 2008 R2
D-4 Installing Windows Server 2008 R2 NOTE: When new partition is created, initial 100MB is assigned as boot partition by Windows OS. Example: If you make a partition of 40,960MB (40GB), usable space will be 40,960MB – 100MB = 40,860MB. The partition size required for a system with an installed memory size of 1GB(1,024MB) and a full installation of the operating system: 8,000MB + (1,024MB * 1.5) + (1,024MB + 300MB) + application size...
Page 433 Installing Windows Server 2008 R2 D-5 BitLocker If you use BitLocker, note the following: Be sure to keep the recovery password secure. Do not keep it around a server running BitLocker. IMPORTANT: Without the recovery password, you cannot start the operating system and see the partition content encrypted by BitLocker.
Page 434: Preparations For Installation
D-6 Installing Windows Server 2008 R2 INSTALLING Windows Server 2008 R2 Preparations for Installation NEC EXPRESSBUILDER DVD-ROM Microsoft Windows Server 2008 R2 Standard (DVD-ROM) / Microsoft Windows Server 2008 R2 Enterprise (DVD-ROM) User's Guide Getting Started...
Page 435: Windows Server 2008 R2 Clean Installation
IMPORTANT: To install Windows Server 2008 R2, you may need to update BIOS. To check if your system needs a BIOS update, go to: http://www.nec.com/express/ Insert the Windows Server 2008 R2 DVD-ROM into your DVD-ROM drive. Restart the system. To restart the system, press Ctrl + Alt + Del or turn off the system once, and then turn it on again.
Page 436 D-8 Installing Windows Server 2008 R2 Select a language and other options from the drop-down lists, and then click [Next]. Click the [Install now ] button. The installation starts.
Page 437 Installing Windows Server 2008 R2 D-9 Select the edition of the Windows operating system that you purchased. NOTE: The Windows versions listed on the screen vary depending on the Windows Server 2008 R2 DVD-ROM you are using. Read the license terms carefully. If you agree, select [I accept the license terms], and then click [Next].
Page 438 The screen of "Where do you want to install Windows?" is displayed. NOTE: Please go to step 12 when you do not use the RAID Controller. Remove the Backup DVD-ROM or Windows Server 2008 R2 DVD-ROM and set NEC EXPRESSBUILDER DVD, and select [Load Driver]. Load Driver...
Page 439 Installing Windows Server 2008 R2 D-11 The folder reference dialog box appears. Select a path in the NEC EXPRESSBUILDER DVD, and then click [OK]. – If the N8103-129/130 RAID Controller is used: <drive letter>:\017\win\winnt\oemfd\ws2008r2\fd1\megasas2 After you select the path, a list of drivers is displayed.
Page 440 D-12 Installing Windows Server 2008 R2 Click [New], enter a partition size, and then click [Apply]. NOTE: When new partition is created, initial 100MB is assigned as boot partition by Windows OS. Select the partition created in step 13, and then click [Format]. Select the partition created, and then click [Next].
Page 441 Installing Windows Server 2008 R2 D-13 When the following message appears, the installation starts automatically. After a full installation of Windows Server 2008 R2 is completed, the following dialog box will prompt you to set or change the password before you log on. Click [OK].
Page 442 D-14 Installing Windows Server 2008 R2 Change the password, and then click the [ ] button. – If you have selected a full installation – If you have selected a Server Core installation NOTE: Administrator password that satisfy the next condition, are required.
Page 443 Installing Windows Server 2008 R2 D-15 When the following message appears, click [OK] to log on. Log on to the system. The steps vary depending on the edition you selected in step 6. – If you have selected a full installation On the [Initial Configuration Tasks] window, enter user information.
Page 444 D-16 Installing Windows Server 2008 R2 – If you have selected a Server Core installation At the command prompt, enter user information. NOTE: For more detailed procedure, see the "Microsoft Windows Server 2008 Step-By-Step Guide". After installations is completed, be sure to execute the tasks described in "Setup of Device Driver (Normally Install in Server)"...
Page 445: Procedure For License Authentication
The setting of SNP function may affect the system performance, so refer to the attention of SNP detail in the following site before setting it. http://www.nec.com/global/prod/express/ Update the system in the situation below: CPU is expanded (expanded to single processor to multi-processor).
Page 446 D-18 Installing Windows Server 2008 R2 Application Process of "Updating the System" "Updating the System" applies the drivers necessary for NEC Express5800 Series. Log on to the system using an administrator account. Insert the NEC EXPRESSBUILDER DVD-ROM into the optical disk drive.
Page 447 Installing Windows Server 2008 R2 D-19 Read the message, and then click [OK]. The update starts. NOTE: The following box appears during the update if you have deployed a full installation of Windows Server 2008 R2. Wait until the update completes. When the following message appears, click [OK] to restart the system.
Page 448: Driver Installation And Advanced Settings
D-20 Installing Windows Server 2008 R2 DRIVER INSTALLATION AND ADVANCED SETTINGS This section describes on how to install and setup various standard drivers mounted on the device. For the information on installing and setting up the driver that is not described in this section, refer to the document attached to the driver.
Page 449: Graphics Accelerator Driver
Installing Windows Server 2008 R2 D-21 Graphics Accelerator Driver If you use standard graphics accelerator drivers, update your system with NEC EXPRESSBUILDER DVD-ROM attached to your system. Standard graphics accelerator drivers will be installed automatically. NOTE: <Windows Server 2008> The graphics accelerator driver is supported only on a server running a full installation.
Page 450: About Windows Activation
D-22 Installing Windows Server 2008 R2 About Windows Activation Windows Server 2008 R2 must be activated before you can use Windows Server 2008 R2. Windows activation process is as follows. For a server running a full installation Select [Control Panel] and click [System and Security], then select [System]. IMPORTANT: If the following message appears, Windows has already been activated on your system.
Page 451 Installing Windows Server 2008 R2 D-23 In the following screen, click [Change product key]. Type the product key shown on your COA label, and click [Next].
Page 452 D-24 Installing Windows Server 2008 R2 Activate Windows. The Windows activation is complete.
Page 453 Installing Windows Server 2008 R2 D-25 For a server running a Server Core installation At the command prompt, type slmgr –dli, and press Enter. IMPORTANT: If the following message appears, Windows has already been activated on your system. Click to exit. Type slmgr –ipk <PID>, and press Enter.
Page 454: Setting For Solving Problems
D-26 Installing Windows Server 2008 R2 Call the above number, inform the representative of the installation ID which you obtained in step 3, and receive a confirmation ID. At the command prompt, type slmgr –atp <CID>, and press Enter. * CID is the confirmation ID that you received from the call center. The Windows activation is complete.
Page 455: Appendix E Installing Windows Server 2008
NOTICE Read the following notes or information before installing the Windows Server 2008. Optional Board Supported by NEC EXPRESSBUILDER The NEC EXPRESSBUILDER DVD-ROM attached to your server supports the following optional boards: NOTE: If you want to install the other boards by using a driver floppy disk ("OEM-Disk for Mass storage device"), except ones listed below,...
Page 456: Service Pack Which Expressbuilder Supports
E-2 Installing Windows Server 2008 Service Pack Which EXPRESSBUILDER Supports The NEC EXPRESSBUILDER DVD-ROM attached to the server supports following combination of the OS installation media and Service Pack. Windows Server 2008 – OS installation media (with Service Pack 2) –...
Page 457: About The System Partition Size
Installing Windows Server 2008 E-3 About the System Partition Size The system partition size can be calculated from the following formula. When the system is Windows Server 2008 64-bit (x64) Edition: Required partition size = size required to install OS + paging file size + dump file size + application size Size required to install OS = 11,600MB (Full Installation) 12,300MB (Full Installation with Service Pack 2)
Page 458: E-4 Installing Windows Server 2008
E-4 Installing Windows Server 2008 Example: The partition size required for a system with an installed memory size of 1GB (1,024MB) and a full installation of the operating system: 11,600MB + (1,024MB * 1.5) + (1,024MB + 300MB) + application size = 14,460MB + application size.
Page 459 Installing Windows Server 2008 E-5 When the system is Windows Server 2008 32-bit (x86) Edition Required partition size = size required to install OS + paging file size + dump file size + application size Size required to install OS = 6,300MB (Full Installation) 9,300MB (Full Installation with Service Pack 2) 9,400MB (Full Installation + Service Pack 2)
Page 460 E-6 Installing Windows Server 2008 Example: The partition size required for a system with an installed memory size of 1GB (1,024MB) and a full installation of the operating system: 6,300MB + (1,024MB * 1.5) + 1,024MB + 300MB + application size = 9,160MB + application size.
Page 461: Preparations For Installation
Installing Windows Server 2008 E-7 INSTALLING Windows Server 2008 Preparations for Installation NEC EXPRESSBUILDER DVD-ROM Microsoft Windows Server 2008 Standard (DVD-ROM) / Microsoft Windows Server 2008 Enterprise (DVD-ROM) User's Guide Getting Started Windows Server 2008 OEM-Disk for EXPRESSBUILDER...
Page 462: Windows Server 2008 Clean Installation
IMPORTANT: To install Windows Server 2008, you may need to update BIOS. To check if your system needs a BIOS update, go to: http://www.nec.com/express/. Insert the Windows Server 2008 DVD-ROM into your DVD-ROM drive. Restart the system. To restart the system, press Ctrl + Alt + Del or turn off the system once, and then turn it on again.
Page 463 Installing Windows Server 2008 E-9 Click the [Install now ] button. The installation starts. Enter your product key, and then click [Next].
Page 464 E-10 Installing Windows Server 2008 Select the edition of the Windows operating system that you purchased. Select [I have selected the edition of Windows that I purchased], and then click [Next]. You will see only possible editions that have been determined by Windows based on the key you entered in step 6.
Page 465 The screen of "Where do you want to install Windows?" is displayed. NOTE: Please go to step 13 when you do not use the RAID Controller. Remove the Backup DVD-ROM or Windows Server 2008 DVD-ROM and set NEC EXPRESSBUILDER DVD, and select [Load Driver]. Load Driver...
Page 466 E-12 Installing Windows Server 2008 The folder reference dialog box appears. Select a path in the NEC EXPRESSBUILDER DVD, and then click [OK]. If the N8103-129/130 RAID Controller is used: – Windows Server 2008 32-bit (x86) Edition <drive letter>:\017\win\winnt\oemfd\ws2008\fd1\megasas2 – Windows Server 2008 64-bit (x64) Edition <drive letter>:\017\win\winnt\oemfd\ws2008x64\fd1\megasas2...
Page 467 When the following message appears, the installation starts automatically. NOTE: If the disk drive contains NEC EXPRESSBUILDER DVD-ROM, you will be prompted to replace a media with that for OS installation. Insert the install media according to the on-screen message.
Page 468 E-14 Installing Windows Server 2008 Log on to the system. The steps vary depending on the edition you selected in step 7. If you have selected a full installation After a full installation of Windows Server 2008 is completed, the following dialog box will prompt you to set or change the password before you log on.
Page 469 Installing Windows Server 2008 E-15 On the [Initial Configuration Tasks] window, enter user information. If you have selected a Server Core installation After a Server Core installation of Windows Server 2008 is completed, press Ctrl + Alt + Del.
Page 470 E-16 Installing Windows Server 2008 Select [Other User]. Log on to the system as an administrator. You need not enter your password in this dialog box. Click the button. Before you log on, you will be prompted to change the password. Click [OK].
Page 471 Installing Windows Server 2008 E-17 Change the password, and then click the button. NOTE: Computer name and Administrator password that satisfy the next condition, are required. More than 6 characters Contains characters from three of the following categories (numbers, uppercase letters, lowercase letters, and signs). When the following message appears, click [OK].
Page 472: Procedure For License Authentication
The setting of SNP function may affect the system performance, so please refer to the attention of SNP detail in the following site before setting it. http://www.nec.com/global/prod/express/ Refer to the public information of SNP function when KB967224 is not applied.
Page 473 Installing Windows Server 2008 E-19 Application Process of "Updating the System" "Updating the System" applies the drivers necessary for NEC Express5800 Series. Log on to the system using an administrator account. Insert the NEC EXPRESSBUILDER DVD-ROM into the optical disk drive.
Page 474 E-20 Installing Windows Server 2008 Read the message, and then click [OK]. The update starts. NOTE: The following box appears during the update if you have deployed a full installation of Windows Server 2008. Wait until the update completes. When the following message appears, click [OK] to restart the system. The system has been updated.
Page 475: Driver Installation And Advanced Settings
Please refer to Chapter 5 "Installing and Setting Device Drivers" for Windows Server 2008 to install and setup LAN driver and PROSet. Graphics Accelerator Driver If you utilize standard graphics accelerator drivers, update your system with NEC EXPRESSBUILDER DVD-ROM attached to your system. Standard graphics accelerator drivers will be installed automatically.
Page 476: Installing Scsi Controller Driver (N8103-75/95/107
E-22 Installing Windows Server 2008 Installing SCSI Controller Driver (N8103-75/95/107) If you use the SCSI Controller N8103-75/95/107, you do not need to install the driver manually. It is automatically installed by Windows Plug-and-Play. Installing SAS Controller Driver (N8103-104A) If you use the SAS Controller N8103-104A, you do not need to install the driver manually. It is automatically installed by Windows Plug-and-Play.
Page 477: About Windows Activation
Installing Windows Server 2008 E-23 About Windows Activation Windows Server 2008 must be activated before you can use Windows Server 2008. Windows activation process is as follows. For a server running a full installation Go to the Start menu, and in the Run dialog box, type slui, and press Enter. IMPORTANT: If the following message appears, Windows has already been activated on your system.
Page 478 E-24 Installing Windows Server 2008 In the following screen, click [Type a different product key]. Type the product key shown on your COA label, and click [Next].
Page 479 Installing Windows Server 2008 E-25 Activate Windows. The Windows activation is complete.
Page 480 E-26 Installing Windows Server 2008 For a server running a Server Core installation At the command prompt, type slmgr –dli, and press Enter. IMPORTANT: If the following message appears, Windows has already been activated on your system. Click to exit. Type slmgr –ipk <PID>, and press Enter.
Page 481 Installing Windows Server 2008 E-27 At the command prompt, type slmgr –atp <CID>, and press Enter. * CID is the confirmation ID that you received from the call center. The Windows activation is complete.
Page 482: The Procedure To Set Pae Option
E-28 Installing Windows Server 2008 The procedure to set PAE option If your 32-bit system has a memory capacity in excess of 4GB, setting PAE option will enable the system to be installed with over 4GB of memory. IMPORTANT: "PAE option" is not supported on Windows Server 2008 Standard.
Page 483: Setting For Solving Problems
Installing Windows Server 2008 E-29 SETTING FOR SOLVING PROBLEMS Set for collecting memory dump using the procedure described in Chapter 5.
Page 485: Appendix F Installing Windows Server 2003 X64 Editions
NOTICE Read the following notes or information before installing the Windows Server 2003 x64 Editions. Optional Board Supported by NEC EXPRESSBUILDER The NEC EXPRESSBUILDER DVD-ROM attached to your server supports the following optional boards: NOTE: If you want to install the other boards by using a driver floppy disk ("OEM-Disk for Mass storage device"), except ones listed below,...
Page 486: Service Pack Which Expressbuilder Supports
F-2 Installing Windows Server 2003 x64 Editions Service Pack Which EXPRESSBUILDER Supports The NEC EXPRESSBUILDER DVD-ROM attached to the server supports following combination of the OS installation media and Service Pack. Windows Server 2003 R2 x64 Edition – OS installation media (with Service Pack 2) –...
Page 487: About The System Partition Size
Installing Windows Server 2003 x64 Editions F-3 About the System Partition Size The system partition size can be calculated from the following formula. Required partition size = Size necessary to install the system + Paging File Size + Dump File Size + Application Size Size necessary to install the system = 4100MB (Windows Server 2003 x64 Editions) = 4100MB (Windows Server 2003 x64 Editions with ServicePack 2)
Page 488: Installing Windows Server 2003 X64 Editions
F-4 Installing Windows Server 2003 x64 Editions INSTALLING Windows Server 2003 x64 Editions Preparations for Installation NEC EXPRESSBUILDER DVD-ROM Microsoft Windows Server 2003 R2 Standard x64 Edition (CD-ROM) / Microsoft Windows Server 2003 R2 Enterprise x64 Edition (CD-ROM) Windows Server 2003 x64 Editions Service Pack 2 (CD-ROM)
Page 489: Creating "Windows Server 2003 X64 Edition Oem-Disk For Expressbuilder
If you have only NEC Express5800 Server to create Windows Server 2003 x64 Edition OEM-Disk for EXPRESSBUILDER, use this procedure. If Windows Server 2003 or Windows can be operated on NEC Express5800 Server, you can use the other procedure described later.
Page 490 Prepare one Flash FDD, or one USB floppy disk drive and 3.5-inch floppy disk. Start the Operating System. Insert the NEC EXPRESSBUILDER DVD-ROM into the optical disk drive of the server. The Menu will appear. Connect the Flash FDD or the USB floppy disk drive.
Page 491: Windows Server 2003 X64 Editions Clean Installation
Installing Windows Server 2003 x64 Editions F-7 Windows Server 2003 x64 Editions Clean Installation This section explains how to perform a clean installation of Windows Server 2003 x64 Editions. IMPORTANT: If you have created the OEM-Disk into the Flash FDD, connect the Flash FDD before you start the system.
Page 492 F-8 Installing Windows Server 2003 x64 Editions The following message is displayed. Please insert the disk labeled manufacturer-supplied hardware support disk into Drive A: *Press ENTER when ready. If you use the floppy disk drive, insert the Windows Server 2003 x64 Edition OEM-Disk for EXPRESSBUILDER into the floppy disk drive, and press Enter.
Page 493 Installing Windows Server 2003 x64 Editions F-9 A list of mass storage devices is displayed. Select the [Adaptec Ultra320 SCSI Cards (Windows 64-bit)] and press Enter. IMPORTANT: If the following message is displayed when you use the N8103-75/107 SCSI controller, press S. The driver you provided seems to be newer than the Windows default driver.
Page 494 F-10 Installing Windows Server 2003 x64 Editions When the following message is shown, press Enter to start "Welcome to Setup". IMPORTANT: If you install Windows Server 2003 x64 Editions on the hard disk larger than 2,097,152MB (2TB), you can specify only a value equal to or less than 2,097,152MB as partition size.
Page 495: Procedure For License Authentication
Installing Windows Server 2003 x64 Editions F-11 Procedure for License Authentication Product Key used in the procedure for license authentication should be matched with the COA label in which the product key contained in Windows Server 2003 is written. NOTES: Execute the activation within 30 days.
Page 496 Log on to the system by the account with administrator authority to the server (such as administrator). Insert the NEC EXPRESSBUILDER DVD-ROM into the optical disk drive of the server. Click Start menu and [Run], and then execute the following command.
Page 497 Installing Windows Server 2003 x64 Editions F-13 When the following message is displayed, make sure to click [Finish] to restart the system. With that, application process of the Hotfix (KB921411) is finished.
Page 498 Log on to the system with the account that has administrative privilege (e.g. administrator). Insert the NEC EXPRESSBUILDER DVD-ROM into the optical disk drive of server. The Autorun Menu will be displayed Left-click on [Setup Windows], and then click [Update the system].
Page 499 Installing Windows Server 2003 x64 Editions F-15 NOTE: The following box appears during the update if you have deployed a full installation of Windows Server 2003 x64 Edition. Wait until the update completes. When the following message appears, "Updating the System" was finished. When you apply Service Pack: Click [Yes], and then go to Step 6.
Page 500 F-16 Installing Windows Server 2003 x64 Editions When the following message appears, select a Service Pack and click [Open] and then, according to a message, please apply it. When the following message appears, click [Yes] to restart the system. The system has been updated.
Page 501 Installing Windows Server 2003 x64 Editions F-17 Recovery Process If "Updating the System" is executed before the application of the "Hotfix for Windows x64 (KB921411)", "!" may be displayed on the USB root hub. If "!" is displayed on the USB root hub, perform application of the "Hotfix for Windows x64 (KB921411)"...
Page 502: Driver Installation And Advanced Settings
F-18 Installing Windows Server 2003 x64 Editions DRIVER INSTALLATION AND ADVANCED SETTINGS This section describes on how to install and setup various standard drivers mounted on the device. For the information on installing and setting up the driver that is not described in this section, please refer to the document attached to the driver.
Page 503 The [Intel(R) PROSet - InstallShield Wizard] dialog starts. Click [Next]. Choose "I accept the terms in the license agreement" and click [Next]. Click [Next]. Click [Install]. When [InstallShield Wizard Completed] window is displayed, click[Finished]. Remove the NEC EXPRESSBUILDER DVD-ROM from the optical disk drive, restart the system.
Page 504: Lan Driver Setting
F-20 Installing Windows Server 2003 x64 Editions LAN Driver Setting Link Speed LAN drivers will be installed automatically, but the link speed and Duplex mode need to be specified manually. IP addresses is not be able to set when the "Internet Protocol (TCP/IP)" check box OFF. This phenomenon will occur with the certain condition.
Page 505 Installing Windows Server 2003 x64 Editions F-21 Refer to the following procedure for WOL (Wake On LAN) setting. When PROSet is not installed Start Device Manager. Point to [Network adapters] and double click following adapter. Open the adapter [Properties]. [Intel(R) 82576 Gigabit Dual Port Server Network Connection] [Intel(R) 82576 Gigabit Dual Port Server Network Connection #2] Click [Power Management] tab and change setting in [Wake On LAN] according to the following list.
Page 506 F-22 Installing Windows Server 2003 x64 Editions When PROSet is installed Start Device Manager. Point to [Network adapters] and double click following adapter. Open the adapter [Properties]. [Intel(R) 82576 Gigabit Dual Port Server Network Connection] [Intel(R) 82576 Gigabit Dual Port Server Network Connection #2] Click [Power Management] tab and change setting in [Wake On LAN] according to the following list.
Page 507: Setup Team
Installing Windows Server 2003 x64 Editions F-23 Setup Team Adapter Fault Tolerance (AFT) is a feature that creates a group containing more than one adapter and automatically converts the process of the working adapter to the other adapter in the group when any trouble occurred on that adapter.
Page 508 F-24 Installing Windows Server 2003 x64 Editions Create Team Open the [Device Manager]. Open [Network adapters] → [Intel(R) xxx] properties. Click [Teaming] tab and check the [Team this adapter with other adapters] check box. Click [New Team]. Fill the name of the team in [Specify a name for the team] and click [Next]. Include the adapter to the team and click [Next].
Page 509 Installing Windows Server 2003 x64 Editions F-25 Remove Team Open the [Device Manager]. Click [Network adapters], and open [TEAM: "Team name"] properties. Click [Setting] tab. Click [Remove Team] button. Click [Yes] to the message. Confirm [TEAM: "Team name"] adapter is not existing in [Network adapters] tree and restart the system.
Page 510: Lan Board Driver (N8104-111/112/119/120/121/122/125A/126
F-26 Installing Windows Server 2003 x64 Editions LAN Board Driver (N8104-111/112/119/120/121/122/125A/126) Install the driver stored in NEC EXPRESSBUILDER DVD. Installation of LAN Board Driver Start Device Manager. Click [Network adapters] and double-click [(Network Adapter Name)]. [(Network Adapter Name) Properties] appears.
Page 511: Graphics Accelerator Driver
Remove the NEC EXPRESSBUILDER DVD-ROM from the optical disk drive, restart the system. Installing SCSI Controller Driver (N8103-75/107) If you use the SCSI Controller N8103-75/107, update your system with NEC EXPRESSBUILDER DVD-ROM attached to your system. The SCSI Controller driver will be installed automatically.
Page 512: About Windows Activation
F-28 Installing Windows Server 2003 x64 Editions About Windows Activation Windows Server 2003 x64 Editions must be activated before you can use Windows Server 2003 x64 Editions. Windows activation process is as follows. NOTE: When you use Windows Server 2003 R2 x64 Editions BackUp CD-ROM, activation process is not needed.
Page 513 Installing Windows Server 2003 x64 Editions F-29 The following screen is displayed. Process "Windows activation" according to the following message.
Page 514: Setting For Solving Problems
F-30 Installing Windows Server 2003 x64 Editions SETTING FOR SOLVING PROBLEMS Set for collecting memory dump using the procedure described in Chapter 5.
Page 515: Appendix G Installing Windows Server 2003
BEFORE INSTALLING WINDOWS SERVER 2003 Read the following notes or information before installing the Windows Server 2003. Optional Board Supported by NEC EXPRESSBUILDER The NEC EXPRESSBUILDER DVD-ROM attached to your server supports the following optional boards: NOTE: If you want to install the other boards by using a driver floppy disk ("OEM-Disk for Mass storage device"), except ones listed below,...
Page 516: Service Pack Which Expressbuilder Supports
G-2 Installing Windows Server 2003 Service Pack Which EXPRESSBUILDER Supports The NEC EXPRESSBUILDER DVD-ROM attached to the server supports following combination of the OS installation media and Service Pack. Windows Server 2003 R2 – OS installation media (with Service Pack 2) –...
Page 517: About Removable Media
Installing Windows Server 2003 G-3 About Removable Media Do not set removable media, such as DAT and LTO, into the device mounted on this computer during the Windows installation. Floppy Disk Drive The internal floppy disk drive is not included in your system at the standard configuration. Prepare the optional USB floppy disk drive if necessary.
Page 518: About The System Partition Size
G-4 Installing Windows Server 2003 About the System Partition Size The size for the partition that the system is to be installed can be calculated from the following formula. Required partition size = Size necessary to install the system + Paging File Size + Dump File Size + Application Size Size necessary to install the system = 3500MB (Windows Server 2003 R2) = 3500MB (Windows Server 2003 with Service Pack = 3500MB (Windows Server 2003 R2 with Service...
Page 519: Installing Windows Server 2003
Installing Windows Server 2003 G-5 Dividing into the partition of the recommended size into multiple disks as written below will solve problem that it cannot be reserved in one disk. Set the "Size required for installation + Paging file size". See Chapter 5 and set that debugging information (equivalent to the dump file size) is to be written to a separate disk.
Page 520: Creating "Windows Server 2003 Oem-Disk For Expressbuilder
Before installing, create Windows Server 2003 OEM-Disk for EXPRESSBUILDER. NOTE: If you have already "Windows Server 2003 OEM-Disk for EXPRESSBUILDER" for NEC Express5800 Server which you are going to install Windows Server 2003, you do not need to create it again.
Page 521 If you have only NEC Express5800 Server to create Windows Server 2003 OEM-Disk for EXPRESSBUILDER, use this procedure. If Windows Server 2003 or Windows can be operated on NEC Express5800 Server, you can use the other procedure described later. Follow the steps below.
Page 522 Prepare one Flash FDD, or one USB floppy disk drive and 3.5-inch floppy disk. Start the Operating System. Insert the NEC EXPRESSBUILDER DVD-ROM into the optical disk drive of the server. The Menu will appear. Connect the Flash FDD or the USB floppy disk drive.
Page 523: Windows Server 2003 Clean Installation
Installing Windows Server 2003 G-9 Windows Server 2003 Clean Installation This section explains how to perform a clean installation of Windows Server 2003. IMPORTANT: If you have created the OEM-Disk into the Flash FDD, connect the Flash FDD before you start the system. If you have created OEM-Disk into the floppy disk, connect the USB floppy disk drive before you start the system.
Page 524 G-10 Installing Windows Server 2003 The following message is displayed. Please insert the disk labeled manufacturer-supplied hardware support disk into Drive A: *Press ENTER when ready. If you use the floppy disk drive, Insert the Windows Server 2003 OEM-Disk for EXPRESSBUILDER into the floppy disk drive, and press Enter.
Page 525 Installing Windows Server 2003 G-11 A list of mass storage devices is displayed. Select the [Adaptec Ultra320 SCSI Cards (Windows 32-bit)] and press Enter. IMPORTANT: If the following message is displayed when you use the N8103-75/107 SCSI controller, press S. The driver you provided seems to be newer than the Windows default driver.
Page 526 G-12 Installing Windows Server 2003 When the following message is shown, press Enter to start "Welcome to Setup". IMPORTANT: If you install Windows Server 2003 on the hard disk larger than 2,097,152MB(2TB), you can specify only a value equal to or less than 2,097,152MB as partition size.
Page 527: Procedure For License Authentication
Installing Windows Server 2003 G-13 Procedure for License Authentication Product Key used in the procedure for license authentication should be matched with the COA label in which the product key contained in Windows Server 2003 is written. NOTES: Execute the activation within 30 days. System may be locked after 30 days is passed.
Page 528: Updating The System - Applying Service Pack
Log on to the system by the account with administrator authority to the server (such as administrator). Insert the NEC EXPRESSBUILDER DVD-ROM into the optical disk drive of the server. Click Start menu and [Run], and then execute the following command.
Page 529 Installing Windows Server 2003 G-15 When the following message is displayed, click [Next]. After that, follow the message to continue the process. When the following message is displayed, make sure to click [Finish] to restart the system. With that, application process of the Hotfix (KB921411) is finished.
Page 530 Log on to the system with the account that has administrative privilege (e.g. administrator). Insert the NEC EXPRESSBUILDER DVD-ROM into the optical disk drive of server. The Autorun Menu will be displayed Left-click on [Setup Windows], and then click [Update the system].
Page 531 Installing Windows Server 2003 G-17 NOTE: The following box appears during the update if you have deployed a full installation of Windows Server 2003. Wait until the update completes. When the following message appears, "Updating the System" was finished. When you apply Service Pack: Click [Yes], and then go to Step 6. When you don't apply Service Pack: Click [No], and then go to Step 8.
Page 532 G-18 Installing Windows Server 2003 When the following message appears, select a Service Pack and click [Open] and then, according to a message, please apply it. When the following message appears, click [Yes] to restart the system. The system has been updated.
Page 533 Installing Windows Server 2003 G-19 Recovery Process If "Updating the System" is executed before the application of the "Hotfix for Windows Server 2003 (KB921411)", "!" may be displayed on the USB root hub. If "!" is displayed on the USB root hub, perform application of the "Hotfix for Windows Server 2003 (KB921411)"...
Page 534: Driver Installation And Advanced Settings
Please refer to Chapter 5 "Installing and Setting Device Drivers" for Windows Server 2003 to install and setup LAN driver and PROSet. Graphics Accelerator Driver If you utilize standard graphics accelerator drivers, update your system with NEC EXPRESSBUILDER DVD-ROM attached to your system. Standard graphics accelerator drivers will be installed automatically.
Page 535: Installing Scsi Controller Driver (N8103-75/95/107
EXPRESSBUILDER DVD-ROM attached to your system. The SCSI Controller driver will be installed automatically. Installing SAS Controller Driver (N8103-104A) If you use the SAS Controller N8103-104A, update your system with NEC EXPRESSBUILDER DVD-ROM attached to your system. The SAS Controller driver will be installed automatically.
Page 536: About Windows Activation
G-22 Installing Windows Server 2003 About Windows Activation Windows Server 2003 must be activated before you can use Windows Server 2003. Windows activation process is as follows. NOTE: When you use Windows Server 2003 R2 Backup CD-ROM, activation process is not needed. Click [Run] on [Start] menu.
Page 537 Installing Windows Server 2003 G-23 The following screen is displayed. Process "Windows activation" according to the following message.
Page 538: The Procedure To Set Pae Option
G-24 Installing Windows Server 2003 The procedure to set PAE option If your 32-bit system has a memory capacity in excess of 4GB, setting PAE option will enable the system to be installed with over 4GB of memory. IMPORTANT: However, the Microsoft operating system products which support /PAE switch option are limited.
Page 539: Setting For Solving Problems
Installing Windows Server 2003 G-25 SETTING FOR SOLVING PROBLEMS Set for collecting memory dump using the procedure described in Chapter 5.
Page 541: Appendix H Using A Client Computer Which Has A Cd Drive
Using a Client Computer Which Has a CD Drive The NEC EXPRESSBUILDER disk is DVD so that a client computer which you want to use for managing the server needs a DVD drive. If you want to install the management software of EXPRESSBUILDER to the client without the DVD drive, make a CD-R from EXPRESSBUILDER DVD-ROM according to the following steps.
Page 542 H-2 Using a Client Computer Which Has a CD Drive (This page is intentionally left blank.)
Page 543: Appendix I Accessing Power And Performance Data
Accessing Power and Performance Data This chapter describes how to collect the power and performance data, including power consumption, inlet air temperature, and processor utilization of NEC Express server in usual operation. These are defined in ENERGY STAR® Program Requirements for Computer Servers and must be available to users.
Page 544 I-2 Accessing Power and Performance Data 'call the driver Dim outparams set outparams = oipmi.execmethod_("requestresponse",oinparams) WScript.Echo " Completion Code = 0x" & hex(outparams.Completioncode) If outparams.Completioncode <> 0 Then Wscript.Echo " Not supported" Else 'WScript.Echo " Data LS Byte = 0x" & hex(outparams.ResponseData(1)) 'WScript.Echo "...
Page 545: Inlet Air Temperature
Accessing Power and Performance Data I-3 INLET AIR TEMPERATURE Run the following IPMI commands to access the SDR (Sensor Data Record) and obtain an inlet air temperature data. Get SDR Repository Info Reserve SDR Repository Get SDR Get Sensor Reading Shown below is an example of the file created by Visual Basic Script (e.g.
Page 546 I-4 Accessing Power and Performance Data ' (Get SDR) for each record Dim Record_LS,Record_MS, Offset, Length Dim cnt, sensorNum, sensorType ' First Record Record_LS = 0 Record_MS = 0 For cnt = 0 to RecordCount-1 Offset = 0 Length = 9 oinparams.networkfunction = &ha oinparams.lun = 0 oinparams.responderaddress = &h20...
Page 547 Accessing Power and Performance Data I-5 Sub GetSensor(rv_ls, rv_ms, rc_ls, rc_ms, sensorNum) Dim outtmp, units1, units2, sensortype oinparams.networkfunction = &ha oinparams.lun = 0 oinparams.responderaddress = &h20 oinparams.command = &h23 oinparams.requestdata = array(rv_ls, rv_ms, rc_ls, rc_ms, 20, 14) oinparams.requestdatasize = 6 set outtmp = oipmi.execmethod_("requestresponse",oinparams) units1 = outtmp.ResponseData(3) Select Case outtmp.ResponseData(4)
Page 548 I-6 Accessing Power and Performance Data Sub get2complement(raw, rv, bit) Select Case bit case 4: If raw And &h8 Then rv = 0 - ((&h10 - raw) and &h0f) Else rv = raw End If case 8: If raw And &h80 Then rv = 0 - ((&h100 - raw) and &h0ff) Else rv = raw...
Page 549 Accessing Power and Performance Data I-7 Command Line (Example) C:\VBS> cscript //nologo Sensor.vbs Execution Result (Example) =========================================== ID String = Front Panel Temp Sensor Type = Temperature Current Value = 27 degrees C =========================================== ID String = Baseboard Temp1 Sensor Type = Temperature Current Value = 50 degrees C =========================================== ID String = Baseboard Temp2...
Page 550: Processor Utilization
I-8 Accessing Power and Performance Data PROCESSOR UTILIZATION To collect the utilization of processors, use Win32_PerfFormattedData_PerfOS_Processor class provided with the Windows OS. Shown below is a sample file created by Visual Basic Script (e.g. Proc.vbs). In this script, the processor utilization is collected every 30 seconds. ' Start Script strComputer = "."...
Page 551 Accessing Power and Performance Data I-9 Execution Result (Example) Proc0 : PercentProcessorTime=9 Proc1 : PercentProcessorTime=0 Proc2 : PercentProcessorTime=0 Proc3 : PercentProcessorTime=0 Proc4 : PercentProcessorTime=0 Proc5 : PercentProcessorTime=1 Proc6 : PercentProcessorTime=6 Proc7 : PercentProcessorTime=41 Proc8 : PercentProcessorTime=0 Proc9 : PercentProcessorTime=0 Proc10 : PercentProcessorTime=0 Proc11 : PercentProcessorTime=0 Proc12 : PercentProcessorTime=0 Proc13 : PercentProcessorTime=7...
Page 552 I-10 Accessing Power and Performance Data (This page is intentionally left blank.)
Page 553: Appendix J Product Configuration Record Table
Appendix J Product Configuration Record Table Use this table for information about setup and system environment change. Hardware Main Unit Model name Serial No. Date Installed Clock Serial No. Date Installed Clock Serial No. Date Installed Memory CPU1-DIMM1 Size Serial No. Date Installed CPU1-DIMM2 Size Serial No.
Page 554 J-2 Product Configuration Record Table Port 6 Type Serial No. Capacity Date Installed Type number Port 7 Type Serial No. Capacity Date Installed Type number Port 8 Type Serial No. Capacity Date Installed Type number Backup Device Slot 1 Size Capacity Serial No.
Page 555: Software
Product Configuration Record Table J-3 Software Firmware version Name: Version: Application of RUR media Apply Name: Version: File system HPFS NTFS Others ( Bundled software installed Licensed software installed Application running when a failure occurred...
Page 556 J-4 Product Configuration Record Table (This page is intentionally left blank.)

This manual is also suitable for:

N8100-1644f N8100-1645f N8100-1646f N8100-1647f N8100-1648f N8100-1649f ... Show all

NEC Express5800/R120b-2 User Manual

Chapter 1 Notes on Using Your Server

Chapter 2 General Description

Chapter 3 Setting up Your Server

Chapter 4 Configuring Your Server

Chapter 5 Installing the Operating System with Express Setup

Chapter 6 Installing and Using Utilities

Chapter 7 Maintenance

Chapter 8 Troubleshooting

Chapter 9 Upgrading Your Server

Appendix A Specifications

Appendix B Other Precautions

Appendix C IRQ

Appendix D Installing Windows Server 2008 R2

Appendix E Installing Windows Server 2008

Quick Links

Troubleshooting

Related Manuals for NEC Express5800/R120b-2

Summary of Contents for NEC Express5800/R120b-2