Page 1
COLOR TELEVISION RECEIVER Chassis : K15D Model : CL17M6MQFX/XAP CL17M6MQFX/RCL COLOR TELEVISION RECEIVER CONTENTS Precautions Specifications and IC Data Disassembly and Reassembly Alignment and Adjustment Troubleshooting Exploded View and Parts List Electrical Parts List Block Diagram Wiring Diagram Schematic Diagrams...
Page 5
Specifications and IC Data 2-3 Semiconductor Base Diagrams ELECTROLYTIC- CONDENSER DIODE SPM458AN(Pin 64) U4468B(Pin 16) UPC851B(Pin 42) TRANSISTOR SAW-FILTER TRANSISTOR M1864M KSC5802 KSC815-Y KSA539-Y E B C TRANSISTOR LA7840 TDA6107Q KA7632 KSC2331-Y E C B Fig. 2-1 Semiconductor Base Diagrams Samsung Electronics...
“VOLUME” keys ( Up or Down). The adjust- 6. Cancel the Adjustment Mode by re-pressing ment parameters are listed in the accompany- the “FACTORY” or “Power OFF” keys. ing table, and selected by pressing the CHAN- NEL keys ( Samsung Electronics...
Page 8
0 ~ 1 M atri x U S A FIX (Mono) A u tomatic Gain C ontrol 0 ~ 6 3 0 ~ 1 D y nami c S k i n Tone DVDB D VD B right Offs et Samsung Electronics...
Page 9
AIR/STD/HRC/AFN - U.S Army - Available (U.S.A, Army) X-RAY - Unavailable (South America) - Available (U.S.A) V-CHIP - Unavailable (Canada) TV ↔ AV AV Option TV ↔ AV ↔ DVD - Available (South America) DEMO - Unavailable (U.S.A) Samsung Electronics...
7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts. 8. To protect against shock hazard, use an isola- tion transformer. Samsung Electronics...
Page 11
3. Use the P mode key (on the remote control) for the STANDARD picture. 4. Adjust the Screen VR (on the FBT) so that the voltage on the oscilloscope becomes 125+2.5V (See Fig. 4-1). 125 2.5V Fig. 4-1 Samsung Electronics...
Page 12
Mode with using CA100. See Fig. 4-4. Fig. 4-4 2. Adjust RG,BG so that the levels are suitable to each local area. (c) High-Light Adjustment 1. Set SCT to 50FL(13V : 60FL) in the Factory Service Mode with using CA100. See Fig. 4-4 . Samsung Electronics...
Page 13
8. Since the 4-pole magnets and 6-pole magnets lines in the center area of the screen. interact, the dot movement is complex (Fig. 4-5). RED/BLUE GREEN BLUE BLUE RED/BLUE GREEN 6-Pole Magnet Movement 4-Pole Magnet Movement Fig. 4-5 Center Convergence Adjustment Samsung Electronics...
Page 14
4. Fig. 4-7 4. Adjust with VSL (Vertical-Slope) so that the bottom margin of the picture is 4. Fig. 4-8 5. Adjust with HS (Horizontal Shift) so that the lion-head pattern and CRT centers are aligned. Samsung Electronics...
Page 15
Block Diagram 8. Block Diagram 8-1 K15D T U NE R -F /S V I F SA W V E R T IC AL TECC1040PG32A(38A) M1864M A M P LA7840 I 2C 21/ 22 28 MTS R G B A M P T D A 6107 IC -M C U 50- 53...
Precautions 1. Precautions Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays. 1-1 Safety Precautions 1. Be sure that all of the built-in protective devices are replaced. Restore any missing (READING SHOULD NOT BE ABOVE protective shields.
Page 17
14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheat- ing, and correct any potential hazards. Samsung Electronics...
Precautions 1-2 Servicing Precautions Warning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. Warning2: An electrolytic capacitor installed with the wrong polarity might explode. 1.
Page 19
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Samsung Electronics...
Disassembly and reassembly 3. Disassembly and Reassembly 3-1 Back Cover Removal 1. After removing the screws, press the tension rib and pull the cabinet backwards. 2. To reassemble, press the tension rib (see diagram). Samsung Electronics...
Warning: The FBT is charged with high voltage. Before removing the Anode Cap, discharge the voltage through one of the heat sinks on the main board. 3-3 Speaker Removal 1. Remove the speaker by pressing the tension rib. Samsung Electronics...
Page 22
Always lift the picture tube by grasping it firmly around the faceplate, (2) Never lift the tube by its neck. (3) Do not scratch the picture tube or apply excessive pressure. Fractures of the glass may cause an implosion. Samsung Electronics...
Page 34
Exploded View & Parts List 6. Exploded View & Parts List 6-1 CL17M6MQFX/XAP You can search for the updated part code through ITSELF web site. URL : http://itself.sec.samsung.co.kr Code No Description;Specification Q’ty Remark AA96-01488B ASSY COVER P-FRONT;17M6,(SAMEX),SPK,HIPS AA64-03425B CABINET FRONT;17M6,(SAMEX),HIPS,HB,G4309 AA64-70123A BADGE-BRAND;AL,SAMSUNG,SILVER,L=50,FLAT,...
Page 35
Exploded View & Parts List 6-2 CL17M6MQFX/RCL You can search for the updated part code through ITSELF web site. URL : http://itself.sec.samsung.co.kr Code No Description;Specification Q’ty Remark S.N.A AA96-01488B ASSY COVER P-FRONT;17M6,(SAMEX),SPK,HIPS T0003 AA64-03425B CABINET FRONT;17M6,(SAMEX),HIPS,HB,G4309 CIS3 S.N.A AA64-70123A BADGE-BRAND;AL,SAMSUNG,SILVER,L=50,FLAT, T0057 S.N.A...
IC201S Abnormal Normal Replace Abnormal IC201 S Check the FD801S, D807, IC801S Check the or AC-Fuse Check/Replace (33)Pin (H-Drive) IC802 of IC201S Abnormal Normal Abnormal Check the 122.5V- A Line Check the Normal FBT,D805(D806) Check / Replace Q401 Samsung Electronics...
Need help?
Do you have a question about the CL17M6MQFX/XAP and is the answer not in the manual?
Questions and answers