Thx ultra2 digital / thx select dolby digital ex /dts es / dolby digital surround receiver, progressive scan universal disc player, system control, 3 chip dlp high definition projector, hd ready plasma monitor, reference control preamplifier/power amplifi (39 pages)
Av receivers / remotes/tuners / home system / multi-zone control amplifier / plasma display / dlp projectors / stereo receiver / power amplifiers / multi-channel super audio cd player / cd player / integrated amplifier / stereo tuner / high definition dig (36 pages)
MARANTZ Parts for your equipment are generally available to our National Marantz Subsidiary or Agent. ORDERING PARTS : Parts can be ordered either by mail or by Fax.. In both cases, the correct part number has to be specified.
1. TECHNICAL SPECIFICATIONS Power output (20 Hz – 20 kHz simultaneous drive of both channels) ............100W x 2 (8Ω load) 200W x 2 (4Ω load) Total frequency distortion (20Hz – 20kHz simultaneous drive of both channels, 8Ω load) ................0.01% Output band width (8Ω...
3. ALIGNMENTS Adjustment Procedure Set the power voltage to rated voltage for this adjustment DC Offset Voltage Adjustment INTEGRARED AMPLIFIER PM-11S1 DISPLAY ATT. Digital Voltmeter Digital Voltmeter TONE PRE OUT OPERATE SPEAKER REC OUT INPUT VOLUME SELECTOR POWER ON/OFF SPEAKER PHONES PHONO POWER...
Page 5
Idling Current Adjustment Digital Voltmeter Digital Voltmeter L ch R ch P701 P601 J753 J653 R719 R619 After DC Offset Voltage Adjustment is completed, adjust the Idling Current with the variable resistor R619 and R719 on the PCB (P601/P701). Turn off the power. “+”...
4. SERVICE MODE / TRIM CHECK MODE ( ENGLISH ) DISPLAY button DISPLAY INTEGRARED AMPLIFIER PM-11S1 DISPLAY ATT. AC IN TONE PRE OUT OPERATE SPEAKER CONNECT REC OUT INPUT VOLUME SELECTOR POWER ON/OFF PHONES SPEAKER PHONO POWER VOLUME ON/OFF To enter the Service Mode, press the POWER ON/OFF button with pressing the DISPLAY and ATT buttons to turn on the unit.
Page 7
“-36.0” is displayed and speaker output voltage is set to about 1.0 V. When adjust output level with 1.0V correctly, tune the output voltage of Oscillator to fine adjustment. After, whenever press the TONE button, 1.0V of output level are made into 0dB standard, TRIM adjustment function works and output level changes according to the display.
Page 8
TO ENTER THE TREBLE TRIM ADJUSTMENT MODE. 10. Set frequency of Oscillator to “ 20 kHz “. Whenever press the TONE button, the display changes as follows and output level changes according to the display. 16th 17th 18th 19th Press Press Press Press...
Page 9
DISPLAY button DISPLAY INTEGRARED AMPLIFIER PM-11S1 DISPLAY ATT. AC IN TONE PRE OUT OPERATE CONNECT SPEAKER REC OUT INPUT VOLUME SELECTOR POWER ON/OFF PHONES SPEAKER PHONO POWER VOLUME ON/OFF R ch L ch Oscillator AC Voltmeter AC Voltmeter TONE DISPLAY button DISPLAY INTEGRARED AMPLIFIER PM-11S1 DISPLAY...
5. MAIN MICROPROCESSOR (QU01) UPDATE PROCEDURE Necessary Equipment • Windows PC (Windows2000 or WindowsXP) with COM port • RS232C cable straight type (9pin female - 9Pin female) • Update Disc (90M-PM11S1CDR) • DATA UPDATE KIT (part no.: 90M-PM11S1JIG) 5.1. Connection AC IN RS232C Dsub-9 pin cable (female to female/Straight cable)
Page 13
5.2. Installs of The software (Flash Development Toolkit 3.0) Open the CD-ROM (90M-SM11S1CDR) Disc, and double click soft folder. Double click the FDT setup.exe 90M-SM11S1CDR...
Page 14
Click Next. 4. Choose the language. And click Next. Click Yes.
Page 15
Check to the all check boxes. And click Next. Click Next. Check to the all check boxes. And click Next.
Page 17
12. Click Install. 13. The status bar appears. 14. Click Finish.
Page 18
5.3. The writing software setup procedure. Launch up the writing software. Click Start / Programs / Renesas / Flash Development Toolkit 3.0 / Flash Development Toolkit 3.0. Click OK. (This window appears at every starting.)
Page 19
Check Create a new project workspace, and click OK. PM-11 is inputted into the Workspace name. ( I t is simultaneously inputted into Project Name.) Click OK. Choose the H8/3687F in Select Device. Click Next.
Page 20
Choose the Serial port No. in the Select Port. Click Next. 8.0 is inputted into the "Enter the CPU crystal frequency for the selected device:". Click Next. Check the BOOT Mode in Select Connection. Choose the 19200 in Select Baud rate. Click Next. Remark: Please remove check mark, if it is contained...
Page 21
Check the Automatic in Protection. Check the Advanced in Messaging. Click Finish.
Page 22
5.4. Writing procedure Click Start Programs Renesas Flash Development Toolkit3.0 Flash Development Toolkit3.0. Click OK. (This window appears at every starting) Check Open a recent project workspace, and click OK. The right click PM-11, and Click Add Files..
Page 23
Open the CD-ROM (90M-PM11S1CDR) and double click soft folder. Select V040708.mot, and Click Add. The holder of V040708.mot is made.
Page 24
It checks that PM-11S1 and the COM port are connected by RS232C cable. Press POWER Button to turn on the unit. The unit is in the boot mode.( LED and LCD display on the front panel disappear.) 10. The right click V040708.mot, and Click Download File. 11.
Page 25
12. The Main microprocessor (QU01) has been Update. 13. Turn off Power switch, then disconnect FFC cable from PM-11S1. 14. Check the version number of the firmware Refer to “3. TRIM CHECK MODE” on page 4.
7. BLOCK DIAGRAM INPUT SELECTOR PHONO RECORDER-1 MC/MM RIAA REC OUT SELECT RECORDER-2 BALANCED REC SELECTOR/MUTE PRE OUT/MUTE PRE OUT LINE-1 H.P.OUT WM8816 LINE-2 SPK-A OUT TONE MUTE RECORDER-1 RECORDER-2 PROTECT SPK-B OUT BI-AMP SW SPK SELECTOR R-CH ±65V POWER BUFFER NPUT BUFFER, PRE OUT BUFFER, VOLTAGE AMP FUSE START...
8. SCHEMATIC DIAGRAM AD_3 SU74 APU PD01 CU55 PRE_OUT MC_ON 3.3V DISP REC_OUT 1000P PRE OUT 2.7V CU54 REC OUT 2.2V +3VL +5VL +15V 3.2V/15.0V 3.2V/15.0V 3.2V/15.0V 3.2V/15.0V 1000P JU01 SU73 MC ON 1.8V LU21 LU22 OPERATE POWER LU23 MODEL SEL SU72 BLUE PD71...
Page 44
PD01 / QU04 P101 / Q121, Q122 : 74HC4094 Q121 74HC4094 Port Name Function Description STOROBE DATA DATA CLOCK LINE_2 Line_2 input relay ON Active H REC_1 Recorder_1input relay ON Active H REC_2 Recorder_2 input relay ON Active H BI-AMP Bi-amp relay ON Active H LINE_1...
Page 47
007D /L1G 00M04AJ249110 SIDE PANEL SIDE PANEL (GL) 007D /N1G 00M04AJ249110 00M04AJ249110 SIDE PANEL SIDE PANEL (GL) 007D /S1G 00M04AJ249110 SIDE PANEL SIDE PANEL (GL) NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 48
PACKING CASE PACKING CASE 002S 00M04AJ809010 CUSHION CUTSHION(L) 003S 00M04AJ809020 CUSHION CUTSHION(R) 005S /N1G 00M04AJ805010 MASS CARTON MASTER CARTON 005S /N1S 00M04AJ805010 MASS CARTON MASTER CARTON NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
12. ELECTRICAL PARTS LIST NOTE ON SAFETY FOR FUSIBLE RESISTOR : PARTS INFORMATION RESISTORS The suppliers and their type numbers of fusible resistors 1) 00MGD05 × × × 140, Carbon film fixed resistor, ±5% 1/4W are as follows; 2) 00MGD05 × × × 160, Carbon film fixed resistor, ±5% 1/6W 1.
Page 50
00MOA47602540 ELECT. CAP. 47 UF M 25V ARS-TYPE ELNA P101 C515 00MOA47702540 ELECT. CAP. 470UF 25V ARS P101 C516 00MOA47702540 ELECT. CAP. 470UF 25V ARS NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 51
HLMF-K200 #2UL RED H=9 3MM P101 D206 00MHI10005340 00MHI10005340 L.E.D. HLMF-K200 #2UL RED H=9 3MM P101 D207 00MHI10005340 00MHI10005340 L.E.D. HLMF-K200 #2UL RED H=9 3MM NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 52
00MKH04AJ1010 00MKH04AJ1010 UNIT & H-IC HDAM-SA2 MODULE P101 Q215 00MKH04AJ1010 00MKH04AJ1010 UNIT & H-IC HDAM-SA2 MODULE P101 Q216 00MKH04AJ1010 00MKH04AJ1010 UNIT & H-IC HDAM-SA2 MODULE NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 53
00MGD05331160 RESISTOR 330 OHM +- 5% 1/6W P101 R214 00MGD05331160 RESISTOR 330 OHM +- 5% 1/6W P101 R215 00MGD05331160 RESISTOR 330 OHM +- 5% 1/6W NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 54
00MGD05562160 RESISTOR 10K OHM +- 5% 1/6W P101 R346 00MGD05562160 RESISTOR 10K OHM +- 5% 1/6W P101 R347 00MGD05222160 RESISTOR 2.2K OHM +- 5% 1/6W NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 55
00MGD05331160 RESISTOR 330 OHM +- 5% 1/6W P101 RA06 00MGD05331160 RESISTOR 330 OHM +- 5% 1/6W P101 RA07 00MGD05104160 RESISTOR 100K OHM +- 5% 1/6W NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 56
0.01UF 100V FNS P401 C421 00MOF55331580 00MOF55331580 FILM CAP 330PF 100V +- 5% FNS P401 C422 00MOF55331580 00MOF55331580 FILM CAP 330PF 100V +- 5% FNS NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 57
00MKH04AJ1010 00MKH04AJ1010 UNIT & H-IC HDAM-SA2 MODULE P401 QC01 00MKH04AJ1010 00MKH04AJ1010 UNIT & H-IC HDAM-SA2 MODULE P401 QC02 00MKH04AJ1010 00MKH04AJ1010 UNIT & H-IC HDAM-SA2 MODULE NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 58
00MGD05331160 RESISTOR 330 OHM +- 5% 1/6W P401 RC12 00MGD05331160 RESISTOR 330 OHM +- 5% 1/6W P401 RC13 00MGD05222160 RESISTOR 2.2K OHM +- 5% 1/6W NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 59
00MHT800931A0 TRANSISTOR KTC3200 P601 Q652 00MHT600121A0 00MHT600121A0 TRANSISTOR KTA1268 P601 R601 00MGD05100160 RESISTOR 10 OHM +-5% 1/6W P601 R602 00MGD05223160 RESISTOR 22K OHM +-5% 1/6W NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 60
330 OHM +-5% 1/6W P701 R714 00MGD05473160 RESISTOR 47K OHM +-5% 1/6W P701 R717 00MGD05472160 RESISTOR 4.7K OHM +-5% 1/6W P701 R718 00MGD05182160 RESISTOR 1.8K OHM +-5% 1/6W NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 61
00MGD05103160 RESISTOR 10K OHM +- 5% 1/6W P801 R817 00MGD05563160 RESISTOR 56K OHM +- 5% 1/6W P801 R818 00MGD05563160 RESISTOR 56K OHM +- 5% 1/6W NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 62
00MOF55393580 FILM CAP 0.039UF 100V FNS P901 C904 00MOF55393580 00MOF55393580 FILM CAP 0.039UF 100V FNS P901 C951 00MOA47602520 ELECT. CAP. 47 UF M 25V RA-2 NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 63
00MOF15221540 FILM CAP 220PF J 100V APSV PA01 C184 /S1G 00MOF15221540 FILM CAP 220PF J 100V APSV PA01 C185 /K1G 00MOF15221540 FILM CAP 220PF J 100V APSV NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 64
100PF J 100V APSV PC01 CC05 /N1S 00MOF15101540 00MOF15101540 FILM CAP 100PF J 100V APSV PC01 CC05 /S1G 00MOF15101540 FILM CAP 100PF J 100V APSV NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 65
00MFC90020210 FERRITE CORE MLB-1608-1000A-N2 PD01 LU04 00MFC90020210 00MFC90020210 FERRITE CORE MLB-1608-1000A-N2 PD01 LU05 00MFC90020210 00MFC90020210 FERRITE CORE MLB-1608-1000A-N2 PD01 LU06 00MFC90020210 00MFC90020210 FERRITE CORE MLB-1608-1000A-N2 NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 66
82K OHM +- 5% 1/16W PD01 RD07 00MNN05823610 CHIP RESISTOR 82K OHM +- 5% 1/16W PD01 RU01 00MNN05104610 CHIP RESISTOR 100K OHM +- 5% 1/16W NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 67
2.2K OHM +- 5% 1/16W PD21 RU68 00MNN05222610 CHIP RESISTOR 2.2K OHM +- 5% 1/16W PD21 RU69 00MNN05222610 CHIP RESISTOR 2.2K OHM +- 5% 1/16W NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 68
00MFC90050060 00MFC90050060 FERRITE CORE FERRIT BEADS (B-01-RT) PG01 QG01 00MHT600111B0 00MHT600111B0 TRANSISTOR KTA1267 PG01 QG02 00MHT800921B0 00MHT800921B0 TRANSISTOR KTC3199 PG01 QG03 00MHT41415100 00MHT41415100 TRANSISTOR 2SD1415 NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 69
00MGD05561160 RESISTOR 560 OGHM +- 5% 1/6W PM01 RM06 00MGD05333160 RESISTOR 33K OHM +- 5% 1/6W PM01 RM09 00MRA02220780 00MRA02220780 TRIMMING RESIST 2.2KOHM RH0638CJ3R TYPE ALPS NOTE : “nsp” PARTS IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Need help?
Do you have a question about the PM-11S1/F1N /K1G /L1G /N1G /S1G/N1S and is the answer not in the manual?
Questions and answers