3 CD CHANGER MINI MINI COMPONENT MAX-870/880/878/888 SERVICE Manual 3CD CHANGER MINI COMPONENT CONTENTS 1. Precautions 2. Specifications 3. Disassembly and Reassembly 4. Alignment and Adjustments 5. Special Circuit Descriptions 6. Troubleshooting 7. Exploded Views and Parts List 8. Electrical Parts List 9.
Examples: Handle brackets, Metal Part metal cabinets, screwheads and control shafts. The current measured should not Ohmmeter exceed 0.5 milliamp. Reverse the power- plug prongs in the AC outlet and repeat. Fig. 1-2 Insulation Resistance Test Samsung Electronics...
Make sure that the 8. Always connect a test instrument's ground portion around the serviced part has not lead to the instrument chassis ground been damaged. before connecting the positive lead; always remove the instrument's ground lead last. Samsung Electronics...
Page 5
SCAN : Manufactured for Scandinavian KATSO SATEESEEN! Market. VARNING: OSYNLIG LASERSTRÅLNING NAR DENNA DEL AR OPPNAD OCH SPARREN AR URKOPPLAD BETRAKTA EJSTRÅLEN! Fig. 1-4 Warning Labels (Location: Disc Clamper, Inner Side of Unit Door or Nearby Unit Chassis ) Samsung Electronics...
Page 6
6. After replacing the Pickup, reopen the Short Terminal. See diagrams below: THE UNIT (1) WRIST-STRAP CONDUCTIVE SHEET FOR GROUNDING short short short short terminal terminal terminal terminal SOH-A1 SOH94T4N SOH91CI(CAR,walkman) (CMS-V10,CMS-V30) SOH91VI(LDP) (CMS-V10,CMS-V30) Samsung Electronics...
Page 7
2. Product Specfications Power source AC 230V 50HZ (option) Power consumption General - MAX-870 340W - MAX-880 550W Dimensions (mm) 270(W) x 317(H) x 340(D) Power output (Front) 100W / Ch(6Ω) (THD 10%) - MAX-870 150W / Ch(6Ω) (THD 10%) - MAX-880 0.08% (1kHz)
* If power is not connected ; Remove the Cabinet-Top and Turn the Gear the clockwise using the hand as shown in figure 3-1-1. Open the Door-CD and pull the Tray in the direction of arrow @. TRAY Figure 3-1-1 Figure 3-1 Samsung Electronics...
Page 10
Disassembly and Reassembly 3-2 CD-Mecha, Door-CD 1. Remove 4 screws #, $. 2. Lift the back of the CD-Mecha to remove. Figure 3-2 Samsung Electronics...
Page 11
3. Remove 2 screws ^ and slide the Main PCB to the rear to remove. Figure 3-3 3-4 Cabinet-Front and Cabinet-Bottom 1. Remove 2 screws &. 2. Slide it to the front by releasing two hooks on the bottom of Cabinet-Front to remove. Figure 3-4 Samsung Electronics...
Page 12
Disassembly and Reassembly 3-5 CD Mecha TRAY STOPPER BASE MAIN Refer to the next page for timming point CD SUB PCB TRAY DISC ASS'Y HOOK CD MAIN PCB Figure 3-5 Samsung Electronics...
Page 13
3-5-3 CD Main PCB Disassembly 1. Remove the Lever-Lifter(9) from the Base-Main by releasing two hooks. 2. Remove four Rubber-CD(0) from the Lever-Lifter and then remove the Deck-CD(“). 3. Remove the Hook. 4. Remove the CD MAIN PCB with the soldering iron. Samsung Electronics...
Page 14
* Align the Gear-Cam with the Gear-Tray as shown ing Figure 3-6, then mount the Tray-Disc. Gear-Cam Gear-Cam Gear-Cam Timming Point Gear-Cam Figure 3-6 * When assembling the Tray-Disc,take extreme care not to engage with Gear-Synchro. Gear-Synchro Insert Gear-Disc Figure 3-7 Samsung Electronics...
Page 15
Remove the Gear (c) ( by pushing the hook. Lift the Gear(b) ). 10. Remove the Gear(a) 1. 11. Remove 2 screws 2 and the then remove the Feed-Motor 3. 12. Remove the Chassis-Deck (M) 4. Figure 3-8 Samsung Electronics...
Page 16
8. Remove the Cover-Gear ( by pushing the hook. 9. Remove the Gear(c) ) by pushing the hook. 10. Lift the Gear(b) 1. 11. Remove the Gear(a) 2. 12. Remove 2 screws 3 and then remove the Feed-Motor 4. 13. Remove the Chassis-Deck(M) 5. Figure 3-9 Samsung Electronics...
98 MHz Adjustment BEACON point SENSITIVITY (TSR2) SEMI-VR(5KΩ) FM IN FM S.S.G Output 450kHz Adjust IVR1 so that “TUNED” of FLT is 5 kΩ lighted (Figure 4-2) *Adjust FM S.S.G level to 23dB Figure4-2 FM Auto Search Level Adjustment Samsung Electronics...
Page 18
2)Press REV PLAY LOCK. playback REV. Mode button. L-CH:Turn JSR2L See the PLAY MTT-150 to the right and PlayBack Same as diagram for 150mV left on Deck 2. out Level above adjustment R-CH:Turn JSR2R to locations. the right and left Samsung Electronics...
Page 19
TP3 as in Figure 6 mV R-CH: JSR4R to Deck2, then press locations Electric 4-6 and read the the right and left current REC button. VTVM VTVM Oscilloscope Cassette Deck Audio OSC. LINE OUT AUX IN IN OUT Figure 4-6 Samsung Electronics...
Focus error bias can be adjusted from the range of +100mV ~ -100mV by connectiong the resistor with pin 63 (FEBIAS). 164K VB> VA> sev-stopb 160K FEBIAS sev-stop <5 Bit Counter> fcmpo FEBIAS fe-stopb Samsung Electronics...
Page 21
Extracting the DC part of RFI and RFO and comparing with the basic DC level, if RF Level is more than basic level, the FOK is output. The focus OK circuit generates a timing window of focus on to monitor the focus search status of focus serve. VC+0.625V Samsung Electronics...
Page 22
As the asymmertry due to variations in disc manufacturing can not be eilminated by thr AC coupling alone, the reference voltage of EFM comparator is controlled utilizing the fact that the generation probability of 1,0 50% each in the binary EFM signals. 100K 100K Samsung Electronics...
Page 23
Therefore, the output on processing monitor photo diode, must be a controlled current for getting regularly output power, thus the APC (Auto Power Control) circuit is composed. From Micom 150K 0.75K 43.5K 150K 300K 150K 5.15K LDON Samsung Electronics...
Page 24
If the control by MUTE signal from micom exist, and when input signal absent, two channel of right and left is builted in. CH2I CH2O GC2I GC2O GC1O GC1I GC1I CH1O MUTEI (From Micom) 5-1-11 Center Voltage Generation Circuit The Center Voltage is generated by using resistor dividing voltage. Samsung Electronics...
Page 25
After 10-track jumping, servo circuit gets out of the liner range and actuator,s tracking is unstable occasionally. Accordingly, unnecessary jumping with many tracking error should be prevented. 470K 680K 680K TDFCT DFCTI 66PF TRACKING 110K PHASE COMPENSATION 470K FSET Samsung Electronics...
Page 26
The characteristics of high frequency phase compensation in focus tracking servo and the characteristics of cut off frequecny in CLV low pass filter are test by FSET pin. SMON 220K 220K 100K SPDLO SMDP 220K 220K Double speed SPDL- SMEF FSET Samsung Electronics...
Does UX1(6MHz) voltage normal ? RD4,RR19,RC13,RZD3 oscillate ? (pin no. 11 ; 5V) RC12,RR22,RR20 Front PCB When the power is Replace -com. ON 'H' displays at pin no. 3 ?(5V) Check the Main PCB RQ7(C1008Y),RR9(22K) RQ6(B1566), RR8(680 ) Samsung Electronics...
Page 28
Base B+? Is Mute selected ? Remove it with Remocon. Check Headphone jack Headphone Jack short ? soldering condition. UIC1( -COM) pin 5 Check the Front PCB UIC1 ( -COM). Check the "H"? Check the Main PCB AQ8L,8R,1L,1R Samsung Electronics...
Page 29
TIC2 (LC72131) TIC2 (LC72131) Oscillator VT Level Changeable? TX2 (7.2MHz) (pin 20) Check the Main PCB TIC2 (LA1836) TFE1 (Front END Pack) If input normal ? TL1 (MW/LW coil) (pin 1,5) Check the Main PCB FIC2 (TDA7439) Function IC Samsung Electronics...
Page 30
Voltage normal? Tape PCB Check the Tape PCB JIC3 (HA12203) pin2,4,39,41 DCW8, DCW9, JIC1,JIC2 Input signal normal? Tape PCB Check the Tape PCB JIC3 (HA12203) pin8,35 JIC3, JIC5 Output signal normal? Check the Main PCB FIC2 (TDA7439) Function IC Samsung Electronics...
Page 31
Check Roulette Control Sensor Check oscillation of NXF100 Is Focus Search ok ? (16.9344MHZ) Does Laser function during Replace PICK UP Focus Search ? Check NIC9286 pin73 voltage Replace NIC9286 during Focus Search : 5V Replace NIC9223 or NIC9258 Samsung Electronics...
Page 32
Troubleshooting 6-2-2 Audio Output Malfunction Malfunction of Audio Output Check voltage of NIC05 : 5V Replace NIC05 Check waveform of NIC9223 Check NIC9223 soldering pin no. 12,13 Replace NIC9223 Check waveform of NC55R,L Check NIC9223 soldering Check Amp Samsung Electronics...
Page 62
Block Diagrams 9-3 IC & TR Internal Diagrams 9-3-1 Main BA4560 : DIC4 NJU3716M : JIC5 DATA Controller Circuit Samsung Electronics...
Page 63
L OUT LEFT L-N3 100K L-N4 100K 0/30dB I CBUS DECDER + LATCHES 2dB STEP R-N1 DIGGND 100K R-N2 100K SPKR ATT VOLUME TREBLE MIDDLE BASS R OUT RIGHT R-N3 Verf 100K R-N4 INPUT MULTIPLEXER AGND 100K GAIN Samsung Electronics...
Page 73
1 SOL VSS2 VDD2 CE32 TC9173 CE P 04 DSP/SSP CONTROL LATCH CE34 NJU3718 CHIP ENABLE SOL2 2 DECK SOLENOID LD ON TRCNT SUBQ DATA INPUT SQDT SUBQ DATA INPUT CLOCK SQRT NJU3716/18/TC9173/M65846 CLK3 NJU3716/18/TC9173/M65846 NJU3716 CE CE33 9-14 Samsung Electronics...
Page 74
VCD / REMAKE RESET TC9173 : JIC6 Name Function REC / R MODE / B HALF / B HALL / B REC / F MODE / A HALF / A HALL / A DO 3 DI 2 CE 33 Samsung Electronics 9-15...
Page 75
VSSA Analog VSS for servo part Micom clock input pin MDATA Micom data input pin Micom data latch input pin RESET Reset input pin MIRROR The mirror output for test The output pin of focus OK comparator 9-16 Samsung Electronics...
Page 76
The input pin for AGC The output pin for AGC The input pin for EFM comparating CAGC The capacitor connection pin for AGC Feedback input pin of E I/V amplifier for EF Balance control GND for RF part Samsung Electronics 9-17...
Page 77
Mute control input (“H”: Mute ON) Latch Signal input from Micom (Schmit Trigger) MDAT Latch Signal input from Micom (Schmit Trigger) Latch Signal input from Micom (Schmit Trigger) SRAM data I/O port8 (MSB) SRAM data I/O port7 9-18 Samsung Electronics...
Page 78
Spindle Motor drive (Velocity control in the PHASE mode) BCKI Audio data bit clock input of 48 bit/Slot (2.1168MHz) TESTV TEST input terminal (GND connection) DSPEED TEST input terminal (VDD connection) LRCHI Channel clock input of 48 bit/Slot (44.1KHz) Samsung Electronics 9-19...
Page 90
Voltage Table KB9223 KA9258 KB9223 KB9223 KB9223 IC Name IC Name STOP MODE PLAY MODE STOP MODE STOP MODE PLAY MODE STOP MODE PLAY MODE STOP MODE PLAY MODE PLAY MODE 2.5V 4.5V 2.5V 4.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 4.5V...
Page 91
-Space Surround Speaker MAX-852P MAX-858P AH68-20195A SS-SPK use (SS-SPK) MAX-860 MAX-868 AH68-20176A SS-SPK use Refer to next page MAX-870 MAX-878 AH68-20177A SS-SPK use MAX-880 MAX-888 AH68-20177A SS-SPK use Schematic Diagram ( ) Component Lay-out ( ) Schematic Diagram ( )
Black cable Black cable Red cable Red cable Power Port is the patent of Polk Audio in U.S.A. Samsung Electronic has the manufacturing license to produce it. *Note : Design and Specfication are subject to change upon improvement without prior notice.