Page 1
Cisco 7600 Series Router Module Guide December 2012 THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED.
Page 2
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks.
Ethernet and Gigabit Ethernet Switching Modules 2-15 C H A P T E R 10/100 and 10/100/1000 Ethernet Switching Modules 2-15 24-Port 10BASE-FL Ethernet Switching Module (WS-X6024-10FL-MT) 2-18 48-Port 10/100/1000BASE-T Ethernet Switching Module (WS-X6148-GE-TX) 2-18 Cisco 7600 Series Router Module Guide OL-9392-05...
Page 4
2-34 8-Port Gigabit Ethernet Switching Module (WS-X6708-10G-3C) 2-34 8-Port Gigabit Ethernet Switching Module (WS-X6708-10G-3CXL) 2-35 Ethernet Module LEDs 2-35 ATM Modules C H A P T E R 1-Port OC-12 ATM Module (WS-X6101-OC12-MMF) Cisco 7600 Series Router Module Guide OL-9392-05...
Page 5
12-1 8-Port T1/E1 PSTN Interface Module (WS-X6608-T1/E1) 12-4 24-Port FXS Analog Interface Module (WS-X6624-FXS) 12-6 Cisco 7600 Series Ethernet Services 20G Line Cards 13-1 C H A P T E R Cisco 7600 Series Ethernet Services 20G Line Cards 13-1...
Preface This preface describes who should read the Cisco 7600 Series Router Module Guide, how it is organized, and its document conventions. Audience Only trained and qualified service personnel (as defined in IEC 60950 and AS/NZS3260) should install, replace, or service the equipment described in this publication.
Preface Section Title Modules Description Modules Overview Provides an overview of the Cisco 7600 series routers modules. Ethernet and Gigabit Ethernet Describes the Ethernet and Gigabit Ethernet switching Switching Modules modules and provides LED descriptions for these modules. ATM Modules Describes the ATM modules and provides LED descriptions for these modules.
Page 11
Means reader take note. Notes contain helpful suggestions or references to material not covered in the publication. Cautions use the following conventions: Means reader be careful. In this situation, you might do something that could result in equipment Caution damage or loss of data. Cisco 7600 Series Router Module Guide OL-9392-05...
éviter les accidents. Pour prendre connaissance des traductions des aver- tissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement. CONSERVEZ CES INFORMATIONS Cisco 7600 Series Router Module Guide OL-9392-05...
Page 13
Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo. GUARDE ESTAS INSTRUCCIONES Cisco 7600 Series Router Module Guide xiii OL-9392-05...
Page 14
Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR Cisco 7600 Series Router Module Guide OL-9392-05...
Preface Related Documentation For instructions on installing and configuring Cisco 7600 series routers, refer to these publications: Regulatory Compliance and Safety Information for the Cisco 7600 Series Routers • Cisco 7609 Router Installation Guide • Cisco 7600 Series Router Module Installation Guide •...
Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html Subscribe to the What’s New in Cisco Product Documentation as an RSS feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service. Cisco currently supports RSS Version 2.0.
C H A P T E R Modules Overview This chapter provides important information about the Cisco 7600 series routers modules. This chapter contains these sections: LEDs, page 1-1 • Port Addresses, page 1-2 • Hot Swapping Modules, page 1-4 •...
“Physical Interface Addresses” section on page 1-2. For Cisco 7600 series routers running Cisco IOS software, refer to the appropriate Cisco 7600 Series Note Cisco IOS Software Configuration Guide, for port address information. The Media Access Control (MAC) address is a standardized data link layer address that is required for every port or device that connects to a network.
All network interface connections (ports) require a unique MAC address. The MAC address of an interface is stored in electrically erasable programmable read-only memory (EEPROM) on a component that resides directly on the interface circuitry. The router system code reads the EEPROM for each Cisco 7600 Series Router Module Guide OL-9392-05...
15 seconds for the system to reinitialize after a module has been removed or replaced. For router module removal and installation procedures, refer to the Cisco 7600 Series Router Module Installation Guide.
If you are using the LX/LH GBIC with MMF, you need to install a patch cord between the Note GBIC and the MMF cable. Refer to the “Patch Cord” section of the Cisco 7600 Series Router Module Installation Guide for details.
LC Fiber-Optic Connector Figure 1-6 RJ-21 Telco Interface Cable Connectors RJ-21 port RJ-21 connector RJ-21 connector RJ-21 connector Port Densities Table 1-2 lists the bandwidth and port densities of the c7600 series routers. Cisco 7600 Series Router Module Guide OL-9392-05...
1000BASE-T GBIC Switch Compatibility Matrix posted with the GBIC documentation on Cisco.com for the list of modules and the required software release level necessary to support this GBIC. To comply with GR-1089 intrabuilding, lightening-immunity requirements, you must use foil-twisted Caution pair (FTP) cable that is properly grounded at both ends.
1-9.) Table 1-4 lists the available GBICs. These eight GBICs are installed in the Cisco 7600 series routers modules that support GBICs and are used with the CWDM Passive Optical System. For more information on the CWDM Passive Optical System, refer to the Installation Note for the Cisco CWDM Passive Optical System.
WS-X6724-SFP Gigabit Ethernet module. The SFP optical transceiver modules use an LC connector. You can use any combination of SFP modules that your Cisco device supports. The only restrictions are that each SFP port must match the wavelength specifications on the other end of the cable and that the cable must not exceed the stipulated cable length for reliable communications.
SFPs to CWDM passive optical system optical add/drop multiplexer (OADM) modules or multiplexer/demultiplexer plug-in modules using single-mode fiber-optic cables with standard SC connectors. Table 1-6 lists the available CWDM SFP wavelengths and color-coding identifier. Cisco 7600 Series Router Module Guide 1-11 OL-9392-05...
The XenPak optical transceiver modules are hot-swappable, transceiver components that you can plug into standard receptacles in modules that convert Gigabit Ethernet electrical signals into a single-mode fiber-optic (SMF) interface. Figure 1-13 shows a XenPak optical transceiver module. Cisco 7600 Series Router Module Guide 1-12 OL-9392-05...
24.85 miles (40 km) Software Requirements For information on the minimum, recommended, and default software versions for the Cisco 7600 series routers, supervisor engines, and modules, refer to the applicable release notes for the latest maintenance release of your software.
The QoS port architecture (Rx/Tx) for this module is 1q4t/2q2t. Note This module is a Class 1 laser product. Refer to the Regulatory Compliance and Safety Information for the Cisco 7600 Series Routers for information on working with lasers. Figure 2-1 24-Port 10BASE-FL Ethernet Switching Module (WS-X6024-10FL-MT)
The QoS port architecture (Rx/Tx) for this module is 1q4t/2q2t. Figure 2-4 48-Port 10/100BASE-T Ethernet Switching Module (WS-X6148-RJ21V) WS-X6348-RJ21 STATUS 48 PORT 10/100 BASE-T SWITCHING MODULE PHONE ETHERNET The front panel LEDs are described in Table 2-3 on page 2-35. Cisco 7600 Series Router Module Guide 2-19 OL-9392-05...
This module is a Class 1 laser product. Refer to the Regulatory Compliance and Safety Information for Note the Cisco 7600 Series Routers for information on working with lasers. The QoS port architecture (Rx/Tx) for this module is 1q4t/2q2t. Figure 2-6...
The QoS port architecture (Rx/Tx) for this module is 1q4t/2q2t. Figure 2-9 48-Port 10/100BASE-T Ethernet Switching Module (WS-X6248A-TEL) WS-X6248-RJ-TEL 48 PORT ETHERNET SWITCHING 10/100 BASE-T MODULE The front panel LEDs are described in Table 2-3 on page 2-35. Cisco 7600 Series Router Module Guide 2-21 OL-9392-05...
Note This module is a Class 1 laser product. Refer to the Regulatory Compliance and Safety Information for the Cisco 7600 Series Routers for information on working with lasers. The QoS port architecture (Rx/Tx) for this module is 1q4t/2q2t. Figure 2-10...
The QoS port architecture (Rx/Tx) for this module is 1q4t/2q2t. Figure 2-13 48-Port 10/100BASE-T Ethernet Switching Module (WS-X6348-RJ-45) WS-X6348-RJ-45 STATUS 48 PORT ETHERNET SWITCHING PHONE 10/100 BASE-T MODULE The front panel LEDs are described in Table 2-3 on page 2-35. Cisco 7600 Series Router Module Guide 2-23 OL-9392-05...
This module is a Class 1 laser product. Refer to the Regulatory Compliance and Safety Information for Note the Cisco 7600 Series Routers for information on working with lasers. The QoS port architecture (Rx/Tx) for this module is 1p1q0t/1p3q1t. Cisco 7600 Series Router Module Guide...
Auxiliary VLANs—Provides automatic VLAN configuration for IP phones using IEEE 802.1Q as • the standards-based VLAN tagging mechanism between the switch and the IP phone. The QoS port architecture (Rx/Tx) for this module is 1q4t/2q2t. Cisco 7600 Series Router Module Guide 2-25 OL-9392-05...
The QoS port architecture (Rx/Tx) for this module is 1p1q0t/1p3q1t. Figure 2-19 48-Port 10/100BASE-T Fabric-Enabled Ethernet Switching Module (WS-X6548-RJ-45) WS-X6548 STATUS 48 PORT 10/100 BASE-T SWITCHING MODULE ETHERNET The front panel LEDs are described in Table 2-3 on page 2-35. Cisco 7600 Series Router Module Guide 2-26 OL-9392-05...
8-Port Gigabit Ethernet Switching Module (WS-X6708-10G-3CXL), page 2-35 • For LED indicators, see the “Ethernet Module LEDs” section on page 2-35. Table 2-2 summarizes some of the features of the Gigabit Ethernet switching modules. Cisco 7600 Series Router Module Guide 2-27 OL-9392-05...
Page 44
DFC 1. The module can be installed in slots 2–6 in the Cisco 7606, slots 2–9 in the Cisco 7609 and OSR-7609, and slots 9–13 in the Cisco 7613 routers. It cannot be installed in slots 2–8 of the Cisco 7613 router. The module requires a Supervisor Engine 720.
These modules are Class 1 laser products. Refer to the Regulatory Compliance and Safety Information Note for the Cisco 7600 Series Routers for information on working with lasers. 16-Port Gigabit Ethernet Switching Module (WS-X6316-GE-TX) The 16-port Gigabit Ethernet switching module (WS-X6316-GE-TX) provides 16 switched, full-duplex Gigabit Ethernet ports.
The QoS port architecture (Rx/Tx) for this module is 1p1q4t/1p2q2t. Figure 2-25 16-Port Gigabit Ethernet Switching Module (WS-X6416-GE-MT) WS-X6416-GE-MT 16 PORT GIGABIT ETHERNET The front panel LEDs are described in Table 2-3 on page 2-35. Cisco 7600 Series Router Module Guide 2-30 OL-9392-05...
2-28.) CWDM GBICs are used with the CWDM Passive Optical System. For more information on the CWDM Note Passive Optical System, refer to the Installation Note for the CWDM Passive Optical System. Cisco 7600 Series Router Module Guide 2-31 OL-9392-05...
Category 5 UTP. The WS-X6516-GE-TX module has a single fabric channel interface. The switching module is upgradable to support distributed forwarding by installing an optional Distributed Forwarding Card (WS-F6K-DFC). The QoS port architecture (Rx/Tx) for this module is 1p1q4t/1p2q2t. Cisco 7600 Series Router Module Guide 2-32 OL-9392-05...
(SFP) 1000BASE-SX, 1000BASE-LX/LH, and 1000BASE-ZX optical transceivers. The WS-X6748-SFP module has a dual fabric channel interface and requires the Supervisor Engine 720. The QoS port architecture (Rx/Tx) for this module is 1q8t/1p3q8t. Cisco 7600 Series Router Module Guide 2-33 OL-9392-05...
The WS-X6816-GBIC can be installed in slots 2 through 9 in the Cisco 7609 router. • The WS-X6816-GBIC can only be installed in slots 9 through 13 in the Cisco 7613 router; it cannot be installed in slots 2 through 8.
The Ethernet and Gigabit Ethernet module front-panel LEDs are described in Table 2-3. Table 2-3 Ethernet and Gigabit Ethernet Module LEDs Color/State Description STATUS Green All diagnostics pass; the module is operational. Cisco 7600 Series Router Module Guide 2-35 OL-9392-05...
Page 52
If the module fails to download code and configuration information successfully during the initial reset, the LED stays red; the module does not come online. The module is not receiving power. Cisco 7600 Series Router Module Guide 2-36 OL-9392-05...
Page 53
Green The voice daughter card is installed. The voice daughter card is not detected or is not installed. 1. This is a good time to verify that all LINK LEDs are functioning. Cisco 7600 Series Router Module Guide 2-37 OL-9392-05...
DTE adapter. You can also use this mode to connect a modem to the console port. • Mode 2—Switch in the out position. This mode is not supported in the Cisco 7600 series routers. Cisco 7600 Series Router Module Guide OL-9392-05...
ATM OC-12 Module (SMF) (WS-X6101-OC12-SMF) WS-X6101-OC12-SMF CONSOLE PORT ACTIVE ACTIVE SIGNAL SIGNAL LINK CONSOLE PORT UNI-622MM UNI-622MM SINGLE MODE OC-12 ATM MODE The front panel LEDs are described in Table 3-1 on page 3-3. Cisco 7600 Series Router Module Guide OL-9392-05...
The port is active (the link is connected and operational). The port is the standby port. SIGNAL Green The active port is receiving a valid signal level through the fiber-optic cable; this condition does not indicate valid framing. Cisco 7600 Series Router Module Guide OL-9392-05...
The FlexWAN and Enhanced FlexWAN modules are installed in a Catalyst 6500 series switch or Cisco 7600 series router that has a supervisor engine with a Multilayer Switch Feature Card (MSFC) and Policy Feature Card (PFC). The MSFC, in conjunction with the Enhanced FlexWAN module, provides multiprotocol routing support with full Internet route connectivity for speeds ranging from serial RS-232 to OC-3.
Page 60
Fast Ethernet PA-1FE-FX PA-1FE-TX PA-2FE-FX PA-2FE-TX 1. Supported on the Enhanced FlexWAN module only. 2. The option to configure the interface as Layer 2 port is not supported on the Enhanced FlexWAN module. Cisco 7600 Series Router Module Guide OL-9392-05...
Page 61
Chapter 4 FlexWAN Module and Enhanced FlexWAN Modules For more information about the MSFC and PFC, refer to the appropriate Cisco 7600 Series Cisco IOS Software Configuration Guide for your software release. Throughout this publication, except where noted, the term MSFC refers to both MSFC and MSFC2, and Note the term PFC refers to both PFC and PFC2.
Page 62
STATUS LED off indicates the module has been powered off with the no power enable command or is Note faulty. For detailed information about port adapter LEDs, refer to the documentation that shipped with your port Note adapter. Cisco 7600 Series Router Module Guide OL-9392-05...
C H A P T E R Multilayer Switch Module This chapter describes the Multilayer Switch Module (MSM) (WS-X6302-MSM). The Multilayer Switch Module provides multiprotocol routing for the switch Ethernet interfaces. Cisco IOS features available for the MSM are listed in Table 5-1.
Page 64
Chapter 5 Multilayer Switch Module Table 5-1 Cisco IOS Features for the Multilayer Switch Module (continued) Feature Description Layer 3-related protocols IGMP v1 and v2 • IGMP snooping • Cisco Group Multicast Protocol (CGMP) server support • Full ICMP support •...
Page 65
You can also use this mode to connect a modem to the console port using the console cable and DCE adapter (labeled “Modem”) that shipped with the switch. Mode 2—Not supported. • Cisco 7600 Series Router Module Guide OL-9392-05...
Network Analysis Module (WS-SVC-NAM-2), page 6-2 • NAMs monitor and analyze network traffic for the Cisco 7600 series routers using Remote Monitoring (RMON), RMON2, and other MIBs. The RMON support that the NAM provides for Ethernet VLANs is an extension of the RMON support provided by the supervisor engine. The switched port analyzer (SPAN) selects network traffic and directs it to the NAM.
Note Netflow Data Export (NDE) • For more information about NDE, refer to the Cisco 7600 Series Cisco IOS Software Configuration Guide . The NAM-1 module has 512 MB of RAM and a 96 MB capture buffer. The front panel LEDs are shown in...
Page 69
Network Analysis Modules Network Analysis Module (WS-SVC-NAM-2) The NAM monitors and analyzes network traffic for the Cisco 7600 series routers using remote monitoring (RMON), RMON extensions for switched networks (SMON), and other management information bases (MIBs). The NAM supports the following RMON groups: RMON groups defined in RFC 1757 •...
Page 70
For information on NAM module hardware and software requirements and port adapter installation and configuration, refer to the Catalyst 6500 Series Switch and Cisco 7600 Series Router Network Analysis Module Release 3.4 Configuration Note. Cisco 7600 Series Router Module Guide...
The term inside refers to networks or network resources protected by the firewall. The term outside refer Note to networks not protected by the firewall. The Firewall Services Module has the following features: Multiple modules—Supports multiple Firewall Services Modules in a Cisco 7600 series routers • chassis. Switch fabric-compatible.
Page 72
• Scalability—Up to two modules are supported in a single Cisco 7600 series router chassis. The following PIX firewall features are not supported by the module: Virtual private networks (VPN) (the module supports IPSec VPN only for management purposes.)
SHUTDOWN button as an alternative shutdown method. For further information on the Firewall Services Module, refer to the Catalyst 6500 Series Switch and Cisco 7600 Series Router Firewall Services Module Configuration Guide, 2.3. Cisco 7600 Series Router Module Guide OL-9392-05...
“interface VLANs.” When you configure a VPN on the Cisco routers, a packet is sent to a routed interface that is associated with an IP address. If the interface has an attached crypto map, the software checks that the packet is on an access control list (ACL) specified by the crypto map.
Page 76
Security and Encryption” section of the Cisco IOS Security Configuration Guide, Release 12.2. When you configure the VPN module on the Cisco 7600 series routers, you ensure that all packets coming from or going to the Internet pass through the VPN module. The VPN module has an extensive set of policies that validate a packet before the packet is sent onto the local (trusted) LAN.
This chapter describes the Intrusion Detection System Module (WS-X6381-IDS). The Intrusion Detection System Module (IDSM) is part of the Cisco Secure Intrusion Detection System (Cisco Secure IDS) and is managed by the Cisco Secure Policy Manager (Cisco Secure PM). (See Figure 9-1.) Cisco Secure PM provides a graphical interface for the management of security across a...
Page 78
To properly shut down the switching module, session into the Intrusion Detection System Module from the Cisco 7600 series router console and enter the shutdown command. If the Intrusion Detection System Module fails to respond to the shutdown command, press the SHUTDOWN button to manually shut down the Intrusion Detection System Module.
All diagnostic tests pass. The module is operational. Orange The module is running through its boot and self-test diagnostics sequence, or the module is disabled. A diagnostic test has failed. The module is powered down. Cisco 7600 Series Router Module Guide 10-1 OL-9392-05...
Engine 1A or Supervisor Engine 720. Switch Fabric Module (WS-C6500-SFM) The Switch Fabric Module (WS-C6500-SFM) requires a Supervisor Engine 2 and must be installed in slot 5 or slot 6 of the Cisco 7606, Cisco 7609, or OSR-7609 routers. (See Figure 11-1.) The Switch Fabric Module cannot be installed in the Cisco 7613 switch or the Cisco 7603 router.
11-2.) The Switch Fabric Module 2 requires Supervisor Engine 2 and must be installed in slot 5 or slot 6 of the Cisco 7606, Cisco 7609, or OSR-7609 routers, or in slot 7 or slot 8 of the Cisco 7613 router.
Communications Media Module (WS-SVC-CMM) The Cisco 7600 series routers Communications Media Module can support single or multiple Cisco CallManagers in a voice-over-IP network. (See Figure 12-1.) The Communications Media...
Page 84
E&M = ear and mouth DTMF = Dual Tone Multi-Frequency DTMF is supported; DTMF/MF is not supported For additional information, refer to the Catalyst 6500 Series and Cisco 7600 Series Communication Media Module Installation and Verification Note. The front panel LEDs are described in Table 12-2.
Page 85
The module is operational; the supervisor engine has • granted module online status. 1. Enter the show environment temperature mod command to display the temperature of each of four sensors on the module. Cisco 7600 Series Router Module Guide 12-3 OL-9392-05...
Telephone Network (PSTN) or transcoding and conferencing. (See Figure 12-4.) The module requires an IP address, is registered with Cisco CallManager in its domain, and is managed by Cisco CallManager. The module software is downloaded from a TFTP server. Depending upon which software you download, the ports can serve as T1/E1 interfaces or support transcoding and conferencing as follows: •...
Page 87
Note To configure the module interfaces, refer to the “Configuring a VoIP Network” chapter of the Catalyst 6500 Series Switch Software Configuration Guide. To configure the interfaces to work with Cisco CallManager, refer to the Cisco CallManager Administration Guide. When the 8-port T1/E1 PSTN interface module powers up, it initializes various hardware components and communicates with the supervisor engine.
The SPAN is in loopback. Yellow No carrier is detected or an AIS signal has been received. The registration with Cisco CallManager is lost. 24-Port FXS Analog Interface Module (WS-X6624-FXS) The 24-port FXS analog interface module (WS-X6624-FXS) interfaces connect directly to standard analog telephones or fax machines.
Page 89
The telephone or fax machine is off-hook. Yellow The module or port is disabled through the CLI The port is not active (connected device is on-hook) or the link is not connected. 1. CLI = command-line interface Cisco 7600 Series Router Module Guide 12-7 OL-9392-05...
Page 90
Chapter 12 Voice-Related Modules 24-Port FXS Analog Interface Module (WS-X6624-FXS) Cisco 7600 Series Router Module Guide 12-8 OL-9392-05...
The Cisco 7600 Series Ethernet Services 20G (ES20) line cards are a multiple-fabric, fixed-port Ethernet line card for the Cisco 7600 series routers that are capable of 20 Gbps of traffic forwarding using a fixed port interface design. The two versions of the Cisco 7600 Series Ethernet Services 20G line card are: 2-port version: 7600-ES20-10G •...
Green and Undefined condition. Amber The port is not enabled by software. Cisco 7600-ES20-GE Line Card LEDs The Cisco 7600-ES20-GE line card has 21 LEDs, as shown in Figure 13-2. Figure 13-2 Cisco 7600-ES20-GE Line Card Faceplate 7600-ES20-GE3CXL ETHERNET...
Page 93
Chapter 13 Cisco 7600 Series Ethernet Services 20G Line Cards Cisco 7600-ES20-GE Line Card LEDs Table 13-2 Cisco 7600-ES20-GE Line Card LEDs (continued) LED Label Color State Meaning Amber The port is enabled but there is not a valid Ethernet link.
Page 94
Chapter 13 Cisco 7600 Series Ethernet Services 20G Line Cards Cisco 7600-ES20-GE Line Card LEDs Cisco 7600 Series Router Module Guide 13-4 OL-9392-05...
SHUTDOWN FIPS APPLICATION CONTROL ENGINE SERVICE MODULE MODE Status LED RJ-45 Console connector USB Port (For Future Use) The STATUS LED displays the Content Switching Module status as described in Table 14-1. Cisco 7600 Series Router Module Guide 14-1 OL-9392-05...
Page 96
• The module is not receiving power, which may be caused by one of the following: Power is not available to the module. – – Module temperature is over the limit1 . Cisco 7600 Series Router Module Guide 14-2 OL-9392-05...
Cisco 7600 Ethernet Services Plus Line Cards The Cisco 7600 Series ES+ line cards are a multiple-fabric, fixed-port Ethernet line card for the Cisco 7600 series routers that are capable of 40 Gbps full-duplextraffic forwarding using a fixed port interface design.
Cisco 7600 ES+ 2TG3C, -3CXL Line Card LEDs For information on which SFPs and XFPs are supported on the Cisco 7600 Series ES+ line cards, see the Cisco 7600 Ethernet Services Plus Line Cards Hardware Installation Guide. For information on configuring features supported on the Cisco 7600 Series ES+ line cards, refer to the Cisco 7600 Ethernet Services Plus Line Cards Configuration Guide.
Undefined condition. Amber The port is not enabled by software. Cisco 7600 ES+ 20G3C, -20G3CXL Line Card LEDs The Cisco 7600 ES+ 20G3C, -20G3CXL line cards have 21 LEDs, as shown in Figure 15-5 Figure 15-6. Cisco 7600 Series Router Module Guide...
Green and Undefined condition. Amber The port is not enabled by software. Cisco 7600 ES+ 40G3C, -40G3CXL Line Card LEDs The Cisco 7600 ES+ 40G3C, -40G3CXL line cards have 21 LEDs, as shown in Figure 15-7 Figure 15-8. Figure 15-7...
Page 101
Chapter 15 Cisco 7600 Ethernet Services Plus Line Cards Cisco 7600 ES+ 40G3C, -40G3CXL Line Card LEDs Figure 15-8 Cisco 7600 ES+ 40G3CXL Line Card Faceplate 7600-ES+ 40G3CXL EXT CLK STATUS CLASS 1 ETHERNET SERVICES MODULE LASER There is one line card STATUS LED and twenty A/L (Active Loopback) LEDs.
Page 102
Chapter 15 Cisco 7600 Ethernet Services Plus Line Cards Cisco 7600 ES+ 40G3C, -40G3CXL Line Card LEDs Cisco 7600 Series Router Module Guide 15-6 OL-9392-05...
C H A P T E R Adaptive Security Appliance Services Module This chapter provides information about the firewall solution, Cisco Adaptive Security Appliance Services Module (ASA SM). This chapter contains the following topics: Functional Overview of Firewalls • ASA SM Overview •...
Cisco Adaptive Security Appliance Services Module (ASA SM) is a high-speed, integrated network security module for Cisco 7600 series routers. ASA SM works with c7600 line cards, and delivers high throughput, low latency, and high availability. ASA SM has more advanced features than the service module, Firewall Services Module (FWSM).
ASA failover mechanism • The mechanism supports the following: high-speed failover between modules within a single Cisco 7600 chassis and high-speed failover between modules in separate chassis. Online diagnostic tests for bootup and periodic health monitoring. Health monitoring tests run at •...
Make the firewall invisible to attackers. • Allow traffic that would be blocked in the routed mode. For example, a transparent firewall can • allow multicast streams using an Ether Type access list. Cisco 7600 Series Routers Module Guide 16-4 OL-9392-04...
ASA SM works with other modules in the router chassis to deliver robust security throughout the entire chassis, effectively making every port a security port. ASA SM and the Firewall Services Module can run simultaneously in the same chassis. Cisco 7600 Series Routers Module Guide 16-5 OL-9392-05...
(PBR) scheme based on the source of the traffic, application types, or destination to route packets across multiple ASA SM cards. For information on all ASA SM configurations, see Cisco ASA Services Module CLI Configuration Note Guide available at: http://www.cisco.com/en/US/docs/security/asa/asa84/configuration85/guide/asa_cfg_cli_85.html...
To detect errors that pertain to major or severe Use the debug trifecta command. events in the firewall module processes ASA SM Documentation Cisco ASA Series Documentation is available at: http://www.cisco.com/en/US/docs/security/asa/roadmap/asaroadmap.html#wp57916 ASA hardware and software compatibility information is available at: http://www.cisco.com/en/US/docs/security/asa/compatibility/asamatrx.html ASA SM compatibility documentation is available at: http://www.cisco.com/en/US/docs/security/asa/roadmap/asaroadmap.html#wp45887...
Page 110
Chapter 16 Adaptive Security Appliance Services Module ASA SM Documentation Cisco 7600 Series Routers Module Guide 16-8 OL-9392-04...
3 to 10 lb (1.4 to 4.5 kg) Regulatory Standards Compliance Cisco 7600 series routers modules comply with the regulatory standards listed in the Regulatory Compliance and Safety Information for the Cisco 7600 Series Routers publication. Cisco 7600 Series Router Module Guide...
Prima di installare, mettere in funzione o effettuare interventi di manutenzione sul sistema, leggere le informazioni contenute nella documentazione sulla Guida alla sicurezza. Tale guida contiene importanti informazioni che è necessario acquisire prima di iniziare qualsiasi intervento sul sistema. Cisco 7600 Series Router Module Guide OL-9392-05...
Warnung Zur Vermeidung einer Beschädigung der Karte durch elektrostatische Entladung während dieses Verfahrens ein Erdungsband am Handgelenk tragen. Bei Berührung der Rückwand mit der Hand oder einem metallenen Werkzeug besteht Elektroschockgefahr. Cisco 7600 Series Router Module Guide OL-9392-05...
(EMI), joka voi haitata muiden laitteiden toimintaa; ja ohjaavat jäähdytysilmavirran asennuspohjan läpi. Laitetta ei saa käyttää, jos kaikki kortit ja peitelevyt eivät ole paikoillaan. Cisco 7600 Series Router Module Guide OL-9392-05...
Page 116
(EMI) som skulle kunna rubba annan utrustning; samt de riktar flödet av kylluft genom chassit. Använd inte systemet om inte alla kort och planskivor finns på plats. Cisco 7600 Series Router Module Guide OL-9392-05...
União Europeia. A conexão da porta a este tipo de rede pública pode causar avarias ou danos severos ao seu distribuidor. Cisco 7600 Series Router Module Guide OL-9392-05...
Evite uma exposição à radiação laser e não olhe através de aberturas expostas, porque poderá ocorrer emissão de radiação laser invisível a partir da abertura da porta, quando não estiver qualquer cabo conectado. Cisco 7600 Series Router Module Guide OL-9392-05...
Page 119
Varning! Osynliga laserstrålar kan sändas ut från öppningen i porten när ingen kabel är ansluten. Undvik exponering för laserstrålning och titta inte in i ej täckta öppningar. Cisco 7600 Series Router Module Guide OL-9392-05...
Page 120
Appendix B Translated Safety Warnings Cisco 7600 Series Router Module Guide OL-9392-05...
Page 122
(figure) LX/LH GBIC LEDs (table) FlexWAN and enhanced FlexWAN features LED description MAC address supported port adapters allocation FlexWAN modules description front panel (figure) module functionality front panel features Cisco 7600 Series Router Module Guide IN-2 OL-9392-05...