American Standard Princeton 4508.801 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. American Standard Manuals
  4. Plumbing Product
  5. Princeton 4508.801
  6. Installation instructions manual

American Standard Princeton 4508.801 Installation Instructions Manual

Spread lavatory faucet with speed connect drain
Hide thumbs
1
2
3
4
5
6
7

Advertisement

Table of Contents

PRINCETON
Spread Lavatory Faucet with
Speed Connect™ Drain
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
Speed Connect™ Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Recommended tools
Screwdriver
1
INSTALL SPOUT
Insert SPOUT (1) and CABLE CONNECTOR (12) through center hole, making sure
the SPOUT ESCUTCHEON (2) and SEAL WASHER (3) are properly seated.
Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto
SPOUT SHANK (7) from under side of sink . Make sure SPOUT (1) is centered
in the mounting hole and the slot in the BRASS WASHER (5) faces toward the
rear of the sink.
Tighten LOCKNUT (6) firmly. Fig. A.
1A
INSTALL VALVE BODY
Place RUBBER RING (9) into SCUTCHEON (10).
Install LOCKNUT (11) onto VALVE BODY (8).
From under side of mounting surface, install VALVE BODY (8) through valve
mounting holes. Threads of VALVE BODY (8) should extent at least 5/16
of a inch above mounting surface top. Fig. B. Thread ESCUTCHEON (10)
onto VALVE BODY (8) until snug against internal stop. If necessary, adjust
LOCKNUT (11).
Hand tighten LOCKNUT (11) to secure VALVE BODY (8).
Repeat above steps for opposite VALVE BODY (8A).
10
9
5/16'' MIN.
Fig. B.
Installation
Instructions
Channel Locks
Adjustable Wrench
Turn off water at
CAUTION
main supply.
10
9
MOUNTING
SURFACE
11
8
11
8
4508.801
Tubing Cutter
1
1
Certified to comply with ANSI A112.18.1
M 9 6 8 8 3 2 R e v . 1 . 3
Fig. A.
1
2
3
7
SLOT
12
8A
4
5
6

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Princeton 4508.801 and is the answer not in the manual?

Questions and answers

Related Manuals for American Standard Princeton 4508.801

Summary of Contents for American Standard Princeton 4508.801

  • Page 1 PRINCETON Spread Lavatory Faucet with Speed Connect™ Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed Connect™ Drain* • Fewer parts, installs in less time • Never needs adjustment •...
  • Page 2 POP-UP DRAIN Remove CLEAR PLASTIC COVER (1). Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). Tighten TAILPIECE (4) on DRAIN BODY before Fig. B. installing DRAIN BODY. REMOVE FLANGE Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain Fig.
  • Page 3 ATTACH CABLE CONNECTOR Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. CHECK OPERATION OF POP-UP Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes.

  • Page 4: Install Handles

    INSTALL HANDLES Push ADAPTER (1) on VALVE STEM (2), so that the hole of the ADAPTER (1) without a spline is facing up. See figure "A". Tighten STEM SCREW (3) to secure ADAPTER (1). Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting male teeth on ADAPTER (1) to female teeth in HANDLE (4).

  • Page 5: Troubleshooting Guide

    Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: •...
  • Page 6 To install the stopper in “Unlocked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear. Rotate Stopper slightly if necessary so that the Stopper slides all the way down.
  • Page 7 M962474-YYY0A LIFT ROD AND KNOB M962248-0070A DECK ADAPTER KIT 918555-0070A HANDLE SCREW 918049-0070A ADAPTER 994053-0070A CARTRIDGE M906617-0070A ATTACHMENT NUT M953006-0070A TEE & HOSE KIT 024220-0070A SUPPLY NUT 066116-YYY0A DRAIN STOPPER 066117-YYY0A M953450-YYY0A 2" FLANGE KIT COMPLETE DRAIN ASSEMBLY M962403-YYY0A LIFT ROD AND KNOB 072574-0070A EXTENSION ROD 066118-0070A...

Table of Contents