Introduction This technical manual describes the system board D2860, which is equipped ® with one Intel processor. Further information about drivers is provided in the readme files on the hard disk, on the supplied “ServerStart“ or “Update“ CDs. You will find further information in the BIOS description.
Information on which system expansions are suitable can be obtained from the customer service centre or your sales outlet. The warranty expires if the device is damaged during the installation or replacement of system expansions. Technical Manual D2860 (BX920)
Page 8
Incorrect replacement of lithium battery may lead to a risk of explosion. The batteries may only be replaced with identical batteries or with a type recommended by the manufacturer. It is essential to observe the instructions in chapter “Replacing the lithium battery”. Technical Manual D2860 (BX920)
Page 9
Use a grounding cable designed for this purpose to connect yourself to the system unit as you install/deinstall the board. Place all components on a static-safe base. You will find a detailed description for handling ESD components in the relevant European or international standards (EN 61340-5-1, ANSI/ESD S20.20). Technical Manual D2860 (BX920)
The board complies with the requirements of the EC directives 2004/108/EC regarding “Electromagnetic Compatibility” and 2006/95/EC “Low Voltage Directive”. This is indicated by the CE marking (CE = Communauté Européenne). Compliance was tested in a typical PRIMERGY configuration. Technical Manual D2860 (BX920)
All batteries containing pollutants are marked with a symbol (a crossed-out rubbish bin on wheels). In addition, the marking is provided with the chemical symbol of the heavy metal decisive for the classification as a pollutant: Cd Cadmium Hg Mercury Pb Lead Technical Manual D2860 (BX920)
Page 12
You will find further information on this at www.ts.fujitsu.com/recycling. For details on returning and reuse of devices and consumables within Europe, refer to the “Returning used devices” manual, or contact your Fujitsu Technology Solutions branch office/subsidiary or our recycling centre in Paderborn:...
– 2x Intel dual-channel Gigabit Ethernet controller Intel 82575X2 – Hard disk controller LSI1064E SAS for 2 SAS hard disks – TPM 1.2 Infineon SLB9635 TT1.2 card (option) – Board Management controller iRMC S2 with integrated graphic controller Technical Manual D2860 (BX920)
Page 14
S2 Server Management controller – basic functionalities: fan control, voltage supervision for onboard voltages, temperature monitoring, System Event Log and ASR&R (Automatic Server Reconfiguration and Restart) – PDA – Global Error/CSS/ID LED – pre-failure warranty for memory Technical Manual D2860 (BX920)
Page 15
– boot possible from: – hard disk (SATA, SAS, SCSI, USB) – USB stick – CD/DVD (SATA, SAS) – LAN – console redirection support – OEM logo – CPU, memory disable – Mirroring and Spare memory support Technical Manual D2860 (BX920)
Page 16
TPM or the system board is faulty you will not be able to access your data. – If a failure occurs, please inform your service about the TPM activation before it takes any action, and be prepared to provide them with your backup copies of the TPM content. Technical Manual D2860 (BX920)
Spare Channel Modus other directions of the population are valid. The memory modules are organized in 3 channels (A - F) per CPU. CPU1 has 3 channels with 2 slots each (1-2) and CPU2 has 3 channels with 1 slot each (1). Technical Manual D2860 (BX920)
Page 18
Only the populated memory of the four channels A, B, D and E can be used (max. 48 GB). The channels C and F serve as safeguarding against failure. Depending on the mode of operation there are different population require- ments for the main memory. Technical Manual D2860 (BX920)
Independent channel mode allows for channels to be populated in any order and no matching between channels is required. Technical Manual D2860 (BX920)
Page 20
Channel A and channel B must be populated identically (channel C is not usable in this mode). Memory slot populations within a channel do not have to be identical but the same memory slot location across channel A and B must be populated the same way. Technical Manual D2860 (BX920)
Page 21
Memory slot populations within a channel do not have to be identical but the same memory slot location across three channels must be populated the same way. Can run with differently rated memory modules and use the settings of the slowest memory module within a channel. Technical Manual D2860 (BX920)
Page 22
Timings in the active channels (A and B) and the spare channel (C) can be set to different values. Only 2/3 of the maximum memory bandwidth is achievable. The total physical memory available to the system is 2/3 of what is populated. Technical Manual D2860 (BX920)
The following functions are supported: Temperature monitoring Measurement of the processor and the system internal temperature by an onboard temperature sensor, measurement of the ambient temperature by a C temperature sensor. Fan control The fans are regulated according to temperature. Technical Manual D2860 (BX920)
Page 24
All monitored events of the system board are signalized via the Global Error LED and recorded in the System Event Log. They could be retrieved in the BIOS Setup or via ServerView. Diagnostic LEDs For signalisation of failures LEDs are situated on the system board. Technical Manual D2860 (BX920)
Error on Mezzanine board 2 By pressing the Indicate CSS button (INDICATE CSS BUTTON near the DIMM slots for CPU2) the defective component can also be indicated in the power-off condition (power supply plug disconnected). Technical Manual D2860 (BX920)
Features Interfaces and connectors 3.6.1 External ports Figure 8: External ports of the system board D2860 Power (green) Connection LED Fabric 1 Identification LED (blue) Connection LED Fabric 2 Global Error LED (red) Connection LED Fabric 3 and 4 CSS LED (yellow)
BIOS setup (the Password on boot field is set to enabled in the SECURITY menu). The password prompt is skipped. The user-defined BIOS passwords are deleted. The password prompt is active (default setting). Technical Manual D2860 (BX920)
Page 29
Figure 10: Position of the TPM jumper (TPM enable) Signal Description TPM RESET L Reset of the TPM module ICH TMP DIS L Reset of ICH10 As default the jumper (1-2) is set. Without jumper the TPM function is disabled. Technical Manual D2860 (BX920)
Page 30
Settings with switches and jumpers Features Technical Manual D2860 (BX920)
Ê Press the locking spring into direction of the arrow (1), so that the lithium battery jumps out of its socket. Ê Remove the battery (2). Ê Insert a new lithium battery of the same type into the socket (3) and (4). Technical Manual D2860 (BX920)