Related Manuals for Extech Instruments SDL200
Summary of Contents for Extech Instruments SDL200
- Page 1 USER GUIDE 4-Channel Thermometer / Datalogger RTD and Thermocouple Inputs Model SDL200...
-
Page 2: Meter Description
Introduction Congratulations on your purchase of the Extech SDL200 Thermometer, an SD Logger Series meter. This meter displays and stores temperature readings from up to four (4) Type K, J, T, E, R, or S thermocouple temperature probes and two (2) 850185 RTD probes. Logged data readings are stored on an SD card for transfer to a PC. -
Page 3: Getting Started
IMPORTANT NOTE: The supplied thermocouple probes are useable in the range of -20 to +250°C (-4 to +482°F) only; even though the meter can display temperature values outside of this range. For measuring outside of the range specified here, please obtain thermocouples rated accordingly. SDL200-EN V2.3 07/13... -
Page 4: Setup Mode
Press the ENTER button to confirm the entry. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode (or simply wait 7 seconds for the meter to automatically switch to the normal operating mode). SDL200-EN V2.3 07/13... - Page 5 Use the arrow buttons to select the type. Press ENTER to confirm setting. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode (or simply wait 7 seconds for the meter to automatically switch to the normal operating mode). SDL200-EN V2.3 07/13...
- Page 6 To exit the MAX-MIN mode, press and hold the MAX-MIN button for at least 1.5 seconds. The meter will beep, the REC-MAX-MIN icons will switch off, the MAX-MIN memory will clear, and the meter will return to the normal operating mode. SDL200-EN V2.3 07/13...
- Page 7 To turn the display backlight ON or OFF, press and hold the backlight button for at least 1.5 seconds. The meter will beep when switching the backlight ON or OFF unless the beeper is disabled as described in the Setup Mode section of this user guide. SDL200-EN V2.3 07/13...
- Page 8 For streaming of data to a PC via the RS232 Output jack, the optional 407001-USB kit (RS232 to USB cable and driver CD) along with the 407001 software (available free at www.extech.com/sdl200) are required. SD Card Information ...
- Page 9 For streaming of data to a PC via the RS232 Output jack, the optional 407001-USB kit (RS232 to USB cable and driver CD) along with the 407001 software (available free at www.extech.com/sdl200) are required. AC Power Adaptor This meter is normally powered by six (6) 1.5V ‘AA’ batteries. An optional 9V power adaptor is available.
-
Page 10: Battery Replacement And Disposal
Please dispose of batteries responsibly; always observe local, state, and federal regulations with regard to battery disposal. Never dispose of batteries in a fire. Batteries may explode or leak. Never mix battery types. Always install new batteries of the same type. SDL200-EN V2.3 07/13... -
Page 11: Specifications
Pt 100 ohm RTD Input (0.00385 alpha coefficient meeting DIN IEC 751) Resolution Range Accuracy 0.1°C -199.9 to 850.0°C ± (0.4 % + 1°C) 0.1°F -327.0 to 999.9°F ± (0.4 % + 1.8°F) 1°F 1000 to 1562°F ± (0.4 % + 2°F) SDL200-EN V2.3 07/13... - Page 12 Accuracy specified for meter only. Input probes add additional measurement error. Generally RTD probes introduce a smaller error than thermocouples. The above specifications are tested under an environmental RF Field Strength lower than 3 V/M and a frequency lower than 30 MHz Copyright © 2013 FLIR Systems, Inc. All rights reserved including the right of reproduction in whole or in part in any form ISO‐9001 Certified www.extech.com SDL200-EN V2.3 07/13...
Need help?
Do you have a question about the SDL200 and is the answer not in the manual?
Questions and answers