Advanced Setup Menu Items; Changing The Speaker Impedance Setting (Speaker Imp.); Turning On/Off The Remote Control Sensor (Remote Sensor); Selecting The Remote Control Id (Remote Con Amp) - Yamaha RX-A1020 Owner's Manual

ADVANCED SETUP menu items

Item Function
SPEAKER IMP. Changes the speaker impedance setting.
REMOTE SENSOR Turns on/off of the remote control sensor on the main unit.
REMOTE CON AMP Selects the unit's remote control ID.
(Asia and General models only)
TUNER FRQ STEP
Changes the FM/AM tuning frequency setting.
TV FORMAT Switches the video signal type.
MONITOR CHECK Removes the limitation on HDMI video output.
Creates backup of the settings of the unit, or recovers the settings
RECOV./BACKUP
from the backup.
INITIALIZE Restores the default settings.
FIRM UPDATE Updates the firmware.
VERSION Checks the version of firmware currently installed on the unit.

Changing the speaker impedance setting (SPEAKER IMP.)

SP IMP. - SPEAKER IMP.
DOCK
TAG
HD
STEREO TUNED PRE AMP PARTY MUTE
ZONE ZONE ZONE
ADAPTIVE
8 MIN
2 3 4
IN OUT 1 OUT 2
ENHANCER SLEEP
HD 3
Change the unit's speaker impedance settings depending on the impedance of the
speakers connected.
Settings
Select this option when you connect 6-ohm speakers to the unit. You
6 Ω MIN
can also use 4-ohm speakers as the front speakers.
Select this option when you connect 8-ohm or higher speakers to the
8 Ω MIN (default)
unit.
VOLUME
DRC
PL L C R PR
SL SW1 SW SW2 SR
PL SBL SB SBR PR
Turning on/off the remote control sensor
(REMOTE SENSOR)
Page
116
SP IMP. - REMOTE SENSOR
DOCK
TAG
HD
STEREO TUNED PRE AMP PARTY
ZONE ZONE ZONE
116
2 3 4
IN OUT 1 OUT 2
ENHANCER SLEEP
HD 3
116
Turn on/off the remote control sensor on the main unit. While the remote control sensor
is turned off, you cannot control the unit from the remote control.
117
Settings
117
ON (default)
117
OFF
118
118

Selecting the remote control ID (REMOTE CON AMP)

118
118
SP IMP. - REMOTE CON AMP
DOCK
TAG
HD
STEREO TUNED PRE AMP PARTY
ZONE ZONE ZONE
2 3 4
IN OUT 1 OUT 2
ENHANCER SLEEP
HD 3
Change the unit's remote control ID so that it matches the remote control's ID (default:
ID1). When using multiple Yamaha AV receivers, you can set each remote control with a
unique remote control ID for its corresponding receiver.
Settings
ID1 (default), ID2
■
Changing the remote control ID of the remote control
Perform each of the following steps within 1 minute. Otherwise, the setting will be
automatically canceled.
1
Press CODE SET on the remote control.
2
Press RECEIVER.
3
Use the numeric keys to enter "5019" (ID1) or "5020" (ID2).
Once the remote control ID is registered successfully, SOURCE blinks twice.
If it blinks six times, registration failed. Repeat from Step 1.
• The registered remote control codes (p.119) are not cleared even if you change the remote control ID.
CONFIGURATIONS ➤ Configuring the system settings (ADVANCED SETUP menu)
MUTE VOLUME
ADAPTIVE DRC
ON
PL L C R PR
SL SW1 SW SW2 SR
PL SBL SB SBR PR
Turns on the remote control sensor.
Turns off the remote control sensor.
MUTE VOLUME
ADAPTIVE DRC
ID1
PL L C R PR
SL SW1 SW SW2 SR
PL SBL SB SBR PR
116
En