Table of Contents
Advertisement
Jig
Saw
Model
4304T
4305T
.
MODEL 4304T
MODEL 4305T
Variable Speed
Variable Speed
INSTRUCTION
~
MANUAL
Length
Max. cutting capacities
Strokes
Overall
Net
of
stroke
Wood
Mild Steel
Aluminum
per minute
length
weight
249 mm
26"
135"
10mm
19-3/4"1
2.4 kg
(1")
(5-5116")
(318")
(:g/yg')
500
~
3,000
287
mm
(5.3
Ibs)
(1 1-5/16',)
43041
4305T
DOUBLE
INSULATION
SPECIFICATIONS
Manufacturer reserves the right t o change specifications without notice.
Note: Specifications may differ from country t o country.
WARNING: For your personal safety, READ and UNDERSTAND before using.
SAVE
THESE
INSTRUCTIONS
FOR
FUTURE REFERENCE.
Advertisement
Table of Contents
Related Manuals for Makita 4304T
Summary of Contents for Makita 4304T
- Page 1 MODEL 4304T Variable Speed MODEL 4305T Variable Speed INSTRUCTION MANUAL 43041 4305T DOUBLE INSULATION SPECIFICATIONS Length Max. cutting capacities Strokes Overall Model per minute stroke Wood Mild Steel Aluminum length weight 249 mm 4304T 26" 135" 10mm 19-3/4"1 2.4 kg (:g/yg') (1")
- Page 2 IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2.
- Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16.
- Page 4 VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified o n the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY t o the user as well as damage t o If in...
-
Page 5: Installing Or Removing The Saw Blade
Do not switch on the tool with the clamp protruding from the blade holder. The clamp, blade holder or roller may be damaged. For 4304T Pull the blade installing lever in the @ direction until stops while lifting slightly. - Page 6 For 4305T 1. Press the button to raise the blade installing knob. Rotate the blade installing knob in the direction and the clamp on the blade holder will open. Open the clamp l i t t l e more than the thickness of the blade to be installed. 3.
-
Page 7: Switch Action
Switch For 4304T CAUTION : Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. To start the tool, simply pull the trigger. Release the trigger to stop. For continuous... - Page 8 Refer to the table right to Select the Pro- per speed for the workpiece to be cut. However, the appropriate speed may differ Mild Steel with the type or thickness of the work- piece. In general, higher speeds will allow Stainless Steel you to cut workpieces faster but the Aluminum...
- Page 9 Flush cutting Loosen the base securing lever and slide the base all the way back. Then tighten the base securing lever to secure the base. cutouts Cutouts can be made with either of two methods A or B. A) Boring a starting hole: For internal cutouts without lead-in cut from and edge, pre-drill starting hole...
- Page 10 Finishing edges edges trim make slight dimensional adjustments, run the blade lightly along the cut edges. Metal cutting Always use a suitable coolant (cutting oil) when cutting metal. Failure to do so will cause significant blade wear. The underside of the workpiece can be greased instead of using a coolant.
- Page 11 To attach the vacuum head on the tool, insert the hook of the vacuum head into the hole in the base. The vacuum head can be installed on either left or right side the base. Then connect a Makita vacuum cleaner to the vacuum head.
- Page 12 Then remove the clamp from the blade holder while rotating the clamp counterclock- wise. To install the clamp, first make sure that the blade installing lever (for 4304T) or knob (for 4305T) has been rotated in the blade loosening direction as far as possible.
- Page 13 ACCESSORIES CAUTION: These accessories or attachments are recommended for use w i t h your Makita tool specified in this manual. The use any other accessories or attachments might present risk injury t o persons. The accessories or attachments should be used only in the proper and intended manner.
- Page 14 Jig saw blade Application Blade type Feature Wood and plywood Plastics Aluminum Mild steel 1 - 6 mm thick thick 1 - 3 mm thick Also ideal for cutting 11/16'' - 118") 13/64" - 1/4"l (3164'' - 1/8"l No. 51 stainless steel.
- Page 15 JIG SAW Model 4304T Note: The switch, noise suppressor and other part configurations may differ from country to country.
- Page 16 Choke Coil Holder Name Plate Gear Housing Cover Complete Tapping Screw Flange PT 4x30 CO"WCt0, Rear Cover Joint Makita Label Driver Rod Tapping Screw CT 4x16 Motor Housing Tapping Screw Flange PT 4x20 Field Retainer Complele c a p A l l...
- Page 17 JIG SAW Model 4305T Note: The switch, noise suppressor and other part configurations may differ from country to country.
- Page 18 Terminal Block 2P P O " 5 Controller Rear Covet Lift Button Knob Name Plate Box Wrench Tapping Screw Flange PT 4x60 Makita Label Head Cover Set [With Item Cord Tapping Screw Flange PT 4x35 Tapping Screw PT 4x55 Cord Guard P,"...
- Page 20 MAKCTA L I M C T E D O N E YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
Need help?
Do you have a question about the 4304T and is the answer not in the manual?
Questions and answers
How do I get the blade out my makita 4304t
To remove the blade from a Makita 4304T, follow these steps:
1. Ensure the tool is switched off and unplugged.
2. Rotate the blade installing lever (for 4304T) or knob (for 4305T) in the blade loosening direction as far as it will go.
3. Remove the clamp from the blade holder while rotating the clamp counterclockwise.
This will allow you to safely remove the blade from the tool.
This answer is automatically generated