Viper FANG 20 User Manual
Original instructions
Hide thumbs
Also See for FANG 20:
- Owner's manual (34 pages) ,
- Quick start manual (52 pages) ,
- Quick start manual (42 pages)
Related Manuals for Viper FANG 20
Summary of Contents for Viper FANG 20
- Page 1 User Manual Original instructions FANG 20 FANG 20T Company information: www.vipercleaning.eu info-eu@vipercleaning.com 82089E (1) – 2012-04-10...
-
Page 3: Table Of Contents
Motor filtEr ClEaning ......................... 19 solution/ClEan watEr filtEr ClEaning ......................... 19 sQuEEgEE bladE CHECk and rEplaCEMEnt ........................20 brusH/pad ClEaning ................................20 TrOBLESHOOTING ..............................20 STOrAGE ..................................21 rECyCLING THE CLEANEr ............................21 82089E (1) – 2012-04-10 FANG 20 / FANG 20T... -
Page 4: Introduction
All necessary operating, maintenance and repair procedures must be performed out by qualified personnel or by Viper Service Centers. only original spare parts and accessories must be used. Contact viper for service or to order spare parts and accessories, specifying the machine model and serial number. -
Page 5: Conventions
− prior to cleaning and servicing − prior to replacing components − prior to changing over the appliance 82089E (1) – 2012-04-10 FANG 20 / FANG 20T... - Page 6 (no use of solvents or other aggressive liquid materials). viper will not pay any claims regarding using aggressive detergents in viper machines. if you need a special detergent for cleaning purposes, please contact your viper dealer.
- Page 7 VIPER will not cover the cost of damages (warranty) caused of this.
- Page 8 Only use the accessories and detergents supplied with the appliance or those specified in the operating instructions.
-
Page 9: Machine Description
(9) solution tank level sight tube (19) protective rollers (29) squeegee vacuum hose (10) Console adjustment levers (20) Front solution fill (30) squeegee adjustment nut & shaft (31) squeegee mounting handwheel 82089E (1) – 2012-04-10 FANG 20 / FANG 20T... -
Page 10: Accessories/Options
Maximum weight with batteries and full tanks brush motor power brush speed brush/pad-holder pressure with extra-pressure 19.0 20.5 function turned off brush/pad-holder pressure with extra-pressure function turned on FANG 20 / FANG 20T 82089E (1) – 2012-04-10... -
Page 11: Wiring Diagram (Fang20-Eu)
USER MANUAL ENGLISH wIrING dIAGrAM (FANG20-EU) WIRING DIAGRAM FOR FANG 20 BATTERY CAPACITY LIGHTS VACUUM BRUSH SOLUTION SWITCH SWITCH SWITCH (16AWG WHT) MAIN (16AWG WHT) CIRCUIT BREAKER 4 (16AWG GRN) (16AWG GRN) 01 KEY SWITCH TRIGGER SWITCH SOLUTION SOLENOID (12AWG RED) -
Page 12: Wiring Diagram (Fang20T-Eu )
ENGLISH USER MANUAL wIrING dIAGrAM (FANG20T-EU ) battEry insert translation solution switCH insert translation battEry CapaCity insert translation spEEd Control insert translation Control board board FANG 20 / FANG 20T 82089E (1) – 2012-04-10... -
Page 13: Operation
For battery choice and installation, apply to qualified battery dealers. set the machine and the battery charger according to the type of batteries installed (wEt or gEl) as shown in the following para- graph. 82089E (1) – 2012-04-10 FANG 20 / FANG 20T... - Page 14 (the wheels on the squeegee point to the back) FANG 20 / FANG 20T 82089E (1) – 2012-04-10...
- Page 15 Adjust amount of solution flow by turning the solution control knob (5). Turn to the right for more solution, or turn left for less solu- tion. notE For correct scrubbing/drying of floors at the sides of the walls, Viper suggests to go near the walls with the right side of the machine as shown. 82089E (1) – 2012-04-10...
- Page 16 (3) turns on, the autonomy is over. after a few seconds, the brush/pad-holder is automatically tuned off, while the vacuum system and the drive system stay on, to finish drying the floor and drive the machine to the appointed recharging area. FANG 20 / FANG 20T 82089E (1) – 2012-04-10...
-
Page 17: While Operating Machine
Once tank is rinsed, flushed and drained, reconnect the clear tube to the hose barb. Be sure the tube is pushed all the way up on 82089E (1) – 2012-04-10 FANG 20 / FANG 20T... -
Page 18: Maintenance
/ brush and clean with approved cleaner. drain recovery and solution tanks completely and rinse out with clean water. visually check the recovery tank for debris and clean out as necessary. FANG 20 / FANG 20T 82089E (1) – 2012-04-10... -
Page 19: Weekly Maintenance
Remove the transparent cover (D) (the water filter position is under the machine), then remove the filter strainer (B). Clean and install them on the support (a). notE The filter strainer (B) must be correctly positioned on the housing (E) of the support (A). 82089E (1) – 2012-04-10 FANG 20 / FANG 20T... -
Page 20: Squeegee Blade Check And Replacement
SOLUTION no power bad batteries replace batteries batteries need to be charged Charge batteries (see battery Charging) loose battery cable tighten loose cable(s) batteries not connected properly follow battery installation instructions FANG 20 / FANG 20T 82089E (1) – 2012-04-10... -
Page 21: Storage
“breathe” during storage. Drain the solution tank of all fluid. rECyCLING THE CLEANEr Make the old cleaner unusable immediately: 82089E (1) – 2012-04-10 FANG 20 / FANG 20T... - Page 22 As specified in European Directive 2002/96/EC on old electrical and electronic appliances, used electrical goods must be collected separately and recycled ecologically. Contact your local authorities or your nearest dealer for further information. FANG 20 / FANG 20T 82089E (1) – 2012-04-10...
- Page 24 Company information: www.vipercleaning.eu info-eu@vipercleaning.com...
Need help?
Do you have a question about the FANG 20 and is the answer not in the manual?
Questions and answers