1. Manuals
  2. Brands
  3. Strong Manuals
  4. Receiver
  5. SRT 7335 CI
  6. User manual

Strong SRT 7335 CI User Manual

Digital high definition satellite receiver
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SRT 7335 CI and is the answer not in the manual?

Questions and answers

Related Manuals for Strong SRT 7335 CI

Summary of Contents for Strong SRT 7335 CI

  • Page 2: Table Of Contents

    PART 1 • English TABLE OF CONTENTS 1.0 INTRODUCTION 1.1 Safety Instructions 1.2 Storage 1.3 Equipment Set-up 1.4 Features & Accessories 2.0 YOUR RECEIVER 2.1 Front Panel 2.2 Rear Panel 2.3 Remote Control Unit 3.0 CONNECTIONS 3.1 Connecting to Satellite Dish 3.2 Connecting to TV &...

  • Page 3: Introduction

    Never use any type of liquid or aerosol cleaner, or any type of organic solvent to clean this product. Attachments-For your safety, and to avoid damaging the product, use only accessories recommended by STRONG. Water and Moisture- Never use this product around water (near a bathtub, kitchen sink, laundry tub, wet basement.

  • Page 4: Storage

    PART 1 • English GENERAL PRECAUTIONS - SAFETY PRECAUTIONS Lightning- If a lightning storm occurs while using a specified AC adapter, remove it from the wall outlet immediately. To avoid damage from unexpected power surges, always unplug the AC adapter from the power outlet and disconnect it from the receiver when the receiver is not in use.

  • Page 5: Equipment Set-Up

    PART 1 • English 1.3 Equipment Set-up We recommend you consult a professional installer to set up your equipment. Otherwise, please follow the instructions below: Refer to the user manual of your TV and your antenna. Make sure that Audio/Video cables and outdoor components are in a good condition and the SCART connections are well shielded.

  • Page 6: Your Receiver

    PART 1 • English 2.0 YOUR RECEIVER 2.1 Front Panel Figure 1 1. POWER Switches the receiver power On and Standby. 2. MENU Gets into Main Page screen. 3. OK Executes the selected item. 4. pq CH Up/Down Channel up/down or selects the item of Menu. 5.

  • Page 7: Rear Panel

    PART 1 • English 2.2 Rear Panel 1. SAT IN To connect the coaxial cable from your LNB on the satellite dish to this connector. 2. SAT OUT Gives you the possibility to connect an extra satellite receiver (analogue or digital). 3.

  • Page 8: Remote Control Unit

    PART 1 • English Important: Connect all components before plugging any power cords into the wall outlet and switching on the receiver and TV set. Always turn on the receiver first, then the TV. 2.3 Remote Control Unit Enables or disables the audio. Switches the receiver between operation and standby mode.
  • Page 9 PART 1 • English 18. INFO Displays the program information box on the screen. 19. V+/V- Turns volume up or down. 20. CH+/CH- Changes channels up or down. Moves up a page in the channel list. In viewing mode selects zoom In/out. Moves down a page in the channel list.

  • Page 10: Connections

    PART 1 • English 3.0 CONNECTIONS 3.1 Connecting to Satellite Dish Connecting a fixed satellite dish to your receiver Make your choice of which satellite you want to receive your signals from, and have your dealer aim your dish at the requested satellite. Connect a coax cable to your LNB and the other end directly to the SAT IN connector of your receiver.

  • Page 11: Connecting To Tv & Vcr

    PART 1 • English Connecting a dish on a motorized positioner to your receiver. Another possibility for watching programs from multiple satellites is by mounting a dish to a motorized DiSEqC 1.2 positioner. Have your dealer mount the dish to the positioner, set the correct angle of the elevation and let him set the center point for your positioner.

  • Page 12: Connecting To Digital Audio Amplifier

    Connect the RS-232 connector on the back of your receiver to the Serial port of your computer using a serial cable. Instructions how to download software can be found on our website www.strong.tv (support -> download). However, this receiver can download new system software by OTA update from satellite.

  • Page 13: Connecting To External Usb - Harddisk

    Ensure that your satellite receiver is correctly connected to your television and dish and your satellite signal is of good quality. Ask your local STRONG dealer to check your installation or satellite signal if you are not sure how to do this.

  • Page 14: Dish Adjustment

    PART 1 • English 4.3 Dish adjustment After selection of ASTRA1C,1E(19E) or HOT BIRD(13E) menu WIZARD-DISH ADJUSTMENT will appear. Adjust your dish position in small steps until the signal strength and quality bars turn green or yellow. Try to reach the maximum possible strength and quality level. Once you are sure the signal cannot be improved, fix the dish on this position and press OK on your remote control to start the channel search.
  • Page 15 PART 1 • English Sort (RED button) Press RED button to select one of available sort options. Original Order the order of the channels will be restored to last stored order Alphabet A-Z or Z-A channels will be sorted in alphabet order Frequency Low-High channels will be sorted in frequency order: first channels with low frequency, then with higher frequency...

  • Page 16: Satellite Search

    PART 1 • English Lock Lock function can be used in order to block access to some channels. Press GREEN button to lock/ unlock channel of your choice. Locked channel will be marked by Lock symbol. In order to watch locked channel you will need to enter PIN code.
  • Page 17 PART 1 • English Network search: if this item is set to “No” then receiver will search for the channels that are available from preset transponder list of selected satellite. If this item is set to “Yes” then receiver in addition will search for the channels from transponders information about that can be found from broadcast.
  • Page 18 PART 1 • English Step by step recommendations of position setup Select reference transponder in order to check signal strength and quality during position setup. If you do not know current direction of your dish then move menu focus to Centre position item and press OK.

  • Page 19: Installation

    PART 1 • English 5.2.3 Edit satellites In this menu you can edit satellite’s name, angle, location and transponder, as well as add new satellite. Press RED button to edit a satellite’s properties. Press GREEN to add new satellite. Edit existing satellite and add new satellite functions are identical. Name: press OK button to edit name of the satellite.
  • Page 20 PART 1 • English Power On Channel Use tu to select an item. If your choice is Fixed channel: press OK button to display a channel list, select a channel and confirm selection with OK button. Your receiver will always start with defined channel.
  • Page 21 Function of this feature depends from broadcast and STRONG would not take any responsibility if it doesn’t work. The default PIN code is 0000.

  • Page 22: Timer

    PART 1 • English 5.3.7 Factory Reset Use Factory Reset only when you want to return the receiver to the condition of factory default. This will delete all user settings and installed channels. 5.4 Timer You can set the timer to make the receiver perform designated actions including timer based wake up or sleep instructions to the receiver.

  • Page 23: Common Interface

    PART 1 • English To format USB memory device Please press YELLOW button (Format). A warning window will appear to get your confirmation of operation. To delete file Press BLUE button (Delete). A warning window will appear to get your confirmation of operation. TIP: When USB memory device is not inserted to the USB port, OSD would not show any files.

  • Page 24: Other Operations

    PART 1 • English 6.0 OTHER OPERATIONS 6.1 Program Guide (EPG) EPG shows the program schedule for the current channel. Availability of EPG depends from broadcast and may not be available for all channels. In no-menu state, press EPG button, the EPG Menu will appear. Screen is divided to 3 main parts: at the left channel list, at the right program schedule list and bottom part provide short program description with program start-end time.

  • Page 25: Pdr Functions

    USB device. STRONG cannot guarantee for USB devices used. Especially when Timeshift is activated at channels with high data rate, STRONG cannot guarantee an accurate Playback of the Timeshift file. Any risk of the PDR function usage shall not be passed to STRONG! 6.4.1 Record...
  • Page 26 PART 1 • English 6.4.2 Play Press u (PLAY) button in TV mode and the Recording File List will appear on screen. Select with the pq buttons the file you want to watch and start playback by pressing OK. You can activate Fast Forward or Fast Rewind during playback by pressing the button.

  • Page 27: Troubleshooting

    PART 1 • English A.1 TROUBLESHOOTING There may be various reasons for the abnormal operation of the receiver. Check the receiver according to the procedures shown below. If the receiver does not work properly after checking it, please contact the dealer.

  • Page 28: Specifications

    PART 1 • English A.2 SPECIFICATIONS Demodulator Demodulation: QPSK, 8-PSK Input Symbol Rate: DVB-S QPSK: 1 ~ 45 Ms/s DVB-S2 8-PSK / QPSK: 10 ~ 30 Ms/s FEC Decoder: 1/2, 2/3, 3/4, 5/6, 7/8 in DVB-S mode; 1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9, 9/10, in DVB-S2 mode Video Decoder Profile Level: MPEG-2 MP@ML, MP@HL, MPEG-4 H.264/AVC...

  • Page 29: Power Consumption

    Communications, CryptoWorks and Irdeto are trademarks of Irdeto Access B.V., Conax is a trademark of Telenor Conax AS, Viaccess is a trademark of France Telecom, Mediaguard is a trademark of Nagra France, all other product names are trademarks or registered trademarks of their respective owners © STRONG 2008. All rights reserved. 12/2008...

  • Page 30: Environmental Issues

    Environmental Issues ENVIRONMENTAL ISSUES STRONG is committed to reducing the impact of its products on the environment. To maximise the benefits of our design enhancements, your co-operation is required. Electronic product recycling Packaging Do not dispose of this product with your When disposing of this domestic rubbish.
  • Page 31 Environmental Issues...

Table of Contents