Table of Contents
Related Manuals for Panasonic NV-HV61GH
Summary of Contents for Panasonic NV-HV61GH
-
Page 1: Table Of Contents
Operating Instructions 使用說明書 Video Cassette Recorder Model No. NV-HV61GH Contents Page Warning and Important Information Controls and Components Connections Tuning the TV to Your VCR Storing TV Broadcasts in Your VCR Setting the Clock of Your VCR Settings Using the On Screen Display... -
Page 2: Warning And Important Information
Plus, [Alumina] Head Cleaner further enhanced cleaning such as a book case or similar unit. efficiency. • Based on in-house tests with Panasonic video cassettes. WARNING: Actual head life may vary according to conditions of use, To reduce the risk of fire, electric shock or product tape type, temperature, humidity, etc. -
Page 3: Controls And Components
ENGLISH Controls and Components (16) (17) (34) (35) (18) (19) EJECT TIMER REC REC/OTR TRACKING/V-LOCK (20) -/- - (36) (37) (14) (38) (20) (39) (40) (41) (22) (10) (12) (27) (21) CANCEL INPUT SEL AUDIO PROG PLAY (22) (23) TIMER PROG CHECK I-TIMER... -
Page 4: Connections
Notes: (6) AC Input socket (42) (1) Aerial (Not supplied) • If you are using a Panasonic TV, this setting has already ¢ To mains supply (2) TV Set (Not supplied) been made, and so you do not need to perform the above (3) Aerial Connector setting procedure. -
Page 5: Tuning The Tv To Your Vcr
If Auto Tuning stops halfway by turning the VCR off or a power failure, Or if the VCR is turned on without the aerial connected Panasonic VCR and all channels are skipped: 1 Disconnect the mains lead and then reconnect it. - Page 6 Auto Tuning Using the On Screen Display Manual Tuning Procedure Introduction If the VCR is not correctly tuned by Auto Tuning, follow the The VCR is tuned automatically by Plug in Auto Tuning. procedure below. However, Auto Tuning using the On Screen Display should be 1 Press [MENU] (9) to display the Main menu on the TV performed according to the following method if necessary.
-
Page 7: Setting The Clock Of Your Vcr
Setting the Clock of Your VCR Settings Using the On Screen Display In the event of a power failure, the clock will operate on its back up system for a minimum of 3 years. After 3 years, clock Preparations back up in the event of a power failure can only be •... -
Page 8: Option Setting
4 Tape running display Option Setting Stop, Eject Rewind, Review, Index Search:, OPTION MENU TAPE SELECT [AUTO] CLOCK SET Jet Search6, NTSC INPUT SELECT [AUTO] TUNER PRESET NTSC PB SELECT [onPALTV] SYSTEM JET NAVIGATOR [OFF] Jet Rewind OPTION DELETE NAVIDATA [NO] OSD REC [OFF]... -
Page 9: Playback
OSD REC: To set the conditions for the OSD Playback Recording function. • Press [2 1] (28) to select [ON] or [OFF]. Preparations • Confirm that the VCR is on. OFF: Initially set at this position. • Confirm that the TV is on and the VCR viewing channel is This setting enables OSD Recording. -
Page 10: Recording
To Play back S-VHS Cassette Tape Recording (SQPB=S-VHS Quasi Playback) It is also possible to play back tapes recorded in the S-VHS Preparations system. • Confirm that the VCR is on. • Some picture noise may occur depending on the type of •... - Page 11 To Display the Approximate Remaining Important Note for the NICAM System When The VCR is switched on, the tuner will automatically Tape Time switch to a NICAM broadcast, if NICAM is being transmitted. The remaining tape time can be displayed in the VCR display. At this time the NICAM signal is transmitted on stereo 1 Select [TAPE SELECT] from the On Screen Display and channels only, since the M1 and M2 formats are not yet...
-
Page 12: Recording From An External Source
Recording from an external source Operations 1 Press [PLAY] (8) to start playback. This function can be used to make up an edited tape from other recordings or video sources. 2 At the point where you want to join a new scene, press A new scene can be added to the end of previous one. -
Page 13: Timer Recording
9 Press [TIMER (REC)] (14) to switch the VCR over to Timer Recording the timer recording standby mode. • When [JET NAVIGATOR] is set to [ON] (see page 8), the [PROGRAMME IS COMPLETE. REMAINING Easy Timer Programming PROGRAMME 49.] message appears. Up to 16 timer programmes, including weekly and daily •... -
Page 14: To Check And Cancel A Timer Programme
Setting other Programmes in Succession Timer recording for the same programme Repeat steps 1-9 of Easy Timer Programming (page 13). on the next week (Intelligent Timer) When you wish to set the timer recording for programmes Programming a Timer Recording of a TV which will be recorded within 1 week and you have ever Programme Until its End recorded the programmes before, you can record them soon... -
Page 15: Search Functions
To Delete the Jet Navigator Data of a Search Functions Single Video Cassette Tape Keep [CANCEL] (5) pressed for more than 5 seconds while Jet Navigator the Jet Navigator list appears. This VCR can display a list of the recorded programmes on [ss] appears on the list. -
Page 16: Time Stamp Function
To Demonstrate the Jet Navigator Function Notes: • Searching in either direction is possible up to the 20th index Keep [NAVI] (25) pressed for more NO.01 JET NAVIGATOR signal. DATE CH ON CATEGORY than 5 seconds without inserting a 1 / 1 0 8 :0 0 M U S I C •... -
Page 17: Before Requesting Service
• The playback picture is distorted when record the tape in the Before Requesting Service EP mode using MESECAM system. #However, this is not a malfunction. #We recommend PAL system for recording in the EP mode. Message of On Screen Display Recording will not operate correctly The error message is indicated in brackets [ The symptom description is indicated in brackets [... -
Page 18: Specifications
If the Still Picture shaking (V-Lock Adjustment): If the problem still persists after performing above, contact a If the still picture shakes, perform the following operation. service personnel to request assistance. Specifications NV-HV61GH Power Source: 110–240 V AC 50/60 Hz Power Consumption: 13 W...