Advertisement
Quick Links
I
30" Slide-in Range
iNSTALLATiON ANDSERVICEMUSTDE PERFORMED BY A QUALiFiED iNSTALLER.
iMPORTANT: SAVE THiS iNSTALLATiON MANUAL FOR LOCAL ELECTRICAL
iNSPECTOR'S USE,
READANDSAVETHESEiNSTRUCTiONS FORFUTUREREFERENCE,
For SAFETY CONSiDERATiONS
do not install a range in any combustible
cabinetry
which
is not in
accord with the stated clearances
and dimensions
on page 2. See Figures 1 and 2.
RANGE MEASUREMENTS . .....................................
2
CLEARANCES ANDDIMENSIONS ..............................
2
iMPORTANT NOTES .............................................
3
UNPACKING ANDEXAMINING YOURRANGE .................
3
IMPORTANT SAFETYINSTRUCTIONS .........................
3
ELECTRICAL C ONNECTIONS ................................
4-6
ANTI-TIP ....................................................
6-7
MODELANDSERIAL NUMBER LOCATION ....................
8
CARE,CLEANING ANDMAINTENANCE......................
8
®
Insight
_"
Advertisement
Related Manuals for Sharp KB-4425JW
Summary of Contents for Sharp KB-4425JW
- Page 1 30" Slide-in Range iNSTALLATiON ANDSERVICEMUSTDE PERFORMED BY A QUALiFiED iNSTALLER. iMPORTANT: SAVE THiS iNSTALLATiON MANUAL FOR LOCAL ELECTRICAL iNSPECTOR'S USE, READANDSAVETHESEiNSTRUCTiONS FORFUTUREREFERENCE, For SAFETY CONSiDERATiONS do not install a range in any combustible cabinetry which is not in accord with the stated clearances and dimensions on page 2.
- Page 2 iNSTALLATiON MANUAL If using countertop with 31 1/4" integrated drip edge, remove 5/8-inch to make glass and flush as illustrated. minimum 30" to bottom of cabinet over cooktop 18 _r to upper: cabinets 36_+1/8" to bottom of cooktop surface 23 1/8" *_%_.back Figure 1 contains many range measurements for reference...
-
Page 3: Installation
Microwave Drawer and contact your be dangerous. dealer or a SHARP AUTHORIZED SERVICER. • Do not store or use gasoline or other flammable vapors and liquids near this or any other range. Explosions or fires could result. - Page 4 iNSTALLATiON MANUAL screw The installer or consumer is responsible for connecting the power supply cord to the connection block located behind the back panel access cover. This range may be connected by means of permanent "hard wiring" (flexible armored or nonmetallic shielded copper or aluminum cable), or by means of a power supply cord kit.
- Page 5 iNSTALLATiON MANUAL 3 & 4-WIRE PERMANENT WiRE CONNECTIONS 3-_ ire permanent connection - follo_ steps 1, 2 and 5 belong. 4-wire permanent connection - follow all steps below. 4-WIRE CONNECTION iNSTRUCTiONS Before wiring the range, review the suggested power source location Before wiring the range, review the suggested power source location drawings in Figure 2.
-
Page 6: Normal Installation
iNSTALLATiON MANUAL NORMAL INSTALLATION STEPS ANTI-TIP BRACKET INSTALLATION INSTRUCTIONS IMPORTANT SAFETY WARNING _ect/terminN block To reduce the risk of tipping of the range, the range must be secured Connect I_ne 1 here. to the 11oo1"by properly installed Anti-Tip bracket and screws packed Ground strap... - Page 7 iNSTALLATiON MANUAL 3 LEVEL AND POSiTiON RAHGE DRILL PILOT HOLES FASTEN BRACKET Level range by adjusting the (4) leveling legs with a wrench. Drill a t/S-inch pilot hole where screws are to be located. If bracket is to be mounted to the wall, drill pilot hole at an approximate Note: A minimum...
- Page 8 iNSTALLATiON MANUAL The name plate, including model and serial number, is located on Read the BEFORE YOU CALL and operating instruction sections the faceplate behind the Microwave Drawer front. in your Operation Manual. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship...