Advertisement
iNSTALLATiON
MANUAL
((((
..................................................................................................
.........
Risk of fire or electrical
shock
exists
if an
incorrect
size range cord kit is used or the Installation
Manua!
or strain
relief clamp are disregarded,
Do not loosen the nuts which secure
the factory-
installed
range wiring
to the terminal
block while connecting
range,
Electrica!
Nilure
or toss of" electrical
connection
may
Occur.
ELECTRICAL
SNOCR
NAZARD
* Electrical
ground
is required
on this range,
* Do not connect to the electrical supply until range is permaneNly
grounded.
* DISCONNECT
POWER
TO THE CIRCUIT
BREAKER
OR FUSE BOX BEFORE
MAKING
THE ELECTRICAL
CONNECTION.
* This range
must be connected
to a grounded,
metallic,
permanent
wiring system or the grounding
connector
of the
power cord should be connected
to the grounding
terminal or
wire lead on the range.
* Failure to heed these warnings
could result in a fire, personal
injury or electrica! shock.
208/240
VOlT
CONNNCTION
INSTNUCTION$
The range can be set %r 208V or 240V. The voltage setting %r your
range is pie-set
at 240V from the factory. Follow these steps to
change the voltage setting.
t
Locate
the voltage
switch
on the lower back side of the
range.
2
Remove the screw and rotate the switch plate 180 _ as indicated
in the Figure 3.
3
Reinsert
the switcl_ plate and replace
screw as indicated
in Figure
4. The voltage
setting is indicated
by the visible
marking.
3 & 4oWINN ELECTRICAL
WALL RECEPI"ACLE
TYPN$
&
NNCONMNNDND
NOUNYING
ONINNTATION
ON WALL
Figure
5A illustrates
4-wire
receptacle
required
for new and
remodeled
installations.
Figure 5B illustrates
3-wire receptacle
that is allowed _br existing
installations,
4-wire wall receptacle
(14-50%
Figure
5A
3-wire wall receptacle (10-50R)
Figure
5B
ACCESS
TO TNNNIlNAL
BLO¢I{
Loosen
screw on rear access cover and pull down as illustrated
in
Figm'e 6 to access terminal block wiring connection. 7ib close, retarn
to original location and secure screx_.
strain relief clamp
4
4-WINN
CONNECTION
INSTNUCTmON$oFIGUNN
8
Before wiring the range, re_ Jew the suggested power source location
drawing in Figure 2. If connecting
to a 4-wire electrical system for a
new branch-circuit
or mobile home use a 4-',_ ire connection.
t
Follow
the power
supply
kit manufacturer's
Installation
Instructions
supplied with the strain relief clamp and insta!l.
See Figure 7.
2
Insert the end connectors
for line 1, line 2 and neutral and
tighten securely to the terminal block.
DO NOT LOOSEN
the fz_ctory installed nut
connections
which
secure the range wiring to the terminal
block.
Electrical
fzdNre or loss of electrical
connection
may
occur if these 3 nuts are loosened
or removed.
3
You must disconnect
the ground strap. Remo*e the fz_ctory
installed ground screw and plate to release the copper ground
strap from the frame of the range. Cut and discard the copper
ground strap and plate. KEEP the ground screw.
4
Connect the green ground wire lead with the eyelet to the frame
of the range with the ground screw using the same hole in the
frame where the ground screw was originally
installed.
See
Figure 8.
5
Make sure all screws are tightened
securely and replace the
rear access cover. See Figure 6.
Advertisement
