Related Manuals for Haier 42EP24STV
Summary of Contents for Haier 42EP24STV
- Page 1 PLASMA TV OWNER`S MANUAL MODELS: 42EP24STV Please read this manual carefully and completely before operating the unit, and retain this manual for future reference.
-
Page 2: Warning
WARNING : To reduce the risk of electric shock do not remove cover or back. No user-serviceable parts inside refer service to qualified service personnel. Safety of operators has been taken into consideration at the design and manufacture phase, but inappropriate operation may cause electric shock or fire. To prevent the product from being damaged, the following rules should be observed for the installation, use and maintenance of th product. -
Page 3: Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS Read all of the instructions before using this appliance. When using this appliance, always exercise basic safety precautions, including the following: 1)Save these Instructions ---the safety and operating instructions should be retained for future reference. 2)All warning on the appliance and in the operating instructions should be followed. 3)Cleaning --- Unplug from the wall outlet before cleaning. - Page 4 SAVE THESE INSTRUCTIONS Thank you for using our Haier product. This easy-to-use manual will guide you in getting the best use of your product. Remember to record the model and serial number. They are on label in back of the unit.
-
Page 5: Table Of Contents
Warning...2 Safety Instructions... 3-4 Introduction Controls...6 Connection Options...7 emote Control Key Functions ...8 Installing Batteries...8 Installation Installation instructions...9 VCR Setup ..10 Cable TV Setup ..10 External A/V Source Setup...11 DVD Setup...11 DTV Setup ...12 Monitor Out Setup...12 PC Setup...13 Install the Speakers...14 Install the Stand...15... -
Page 6: Controls
Menu exit Signal source input option Down/Up. Sel ct desired option on MENU or tune to the desired channel. VOLUME Buttons MENU Button 6 Plasma TV Front panel controls EXIT INPUT Power On/Off Button Power Standby Indicator illuminates red in standby mode,illuminates blue when the display is turned on Remote Control Sensor MENU... -
Page 7: Connection Options
VGA Input/Audio input VGA IN AUDIO OUT AUDIO Pr/Cr DVD/DTV Input Connect a component video/audio device to these jacks AUDIO output Real panel controls DVI Input/Audio input connect your cable/PC through the input COMPONENT IN DVI IN Pb/Cb L-AUDIO-R AUDIO External audio/ video output S-Video Input... -
Page 8: R Emote Control Key Functions
When using the remote control. Aim it towards the remote sensor on the TV. Function introduction FREEZE Freezes the currently-viewed picture. Press this key to set sleeptimer. Select PC source Auto adjust for PC FAVORITE no available MTS/SAP Selects MTS sound: Mono, Stereo, and SAP in Analog mode. -
Page 9: Installation Installation Instructions
Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product. Speaker unit(X2) 1 M4X12 Screws 4 Standx1 - The TV can be installed in various ways such as on a wall, or on a desktop etc. - The TV is designed to be mounted horizontally. -
Page 10: Vcr Setup
- To avoid picture noise (interference), leave an adequate distance between the VCR and TV Do not leave a still picture from a VCR on the screen for a long If the 4:3 format is used, the fixed images on the sides of the screen may remain visible on the screen, if this format is used day after day. -
Page 11: External A/V Source Setup
How to connect Connect the audio and video cables from the external equipment's output jacks to the TV`s AV IN input jacks, as shown in the figure. When connecting the TV to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). -
Page 12: Dtv Setup
- To watch digitally broadcast programs, purchase and connect a digital set-top box. How to connect Use the TV`s COMPONENT (Y, Pb, Pr) IN jacks, VGA or DVI IN port for video connections, depending on your set-top box connections available. Then, make the corresponding audio connections. -
Page 13: Pc Setup
How to connect To get the best picture quality, adjust the PC graphics card, if necessary. Use the `s VGA IN or DVI (Digital Visual Interface) IN port for video connections, depending on your PC connector. If the graphic card on the PC does not output analog or digital RGB simultaneously, connect only one of either VGA IN or DVI IN to display the PC on the... -
Page 14: Install The Speakers
Install the Speakers Face the PDP screen upside down on a clean blanket or a bracket and pay attention not to indent the casing. Lay the two speaker aside of the PDP. . Fix 4 ST4X16 screws to the speaker. (position . -
Page 15: Install The Stand
Install the Stand Install the PMMA Baffle After installing the brace pole(see figure below) rip the protective sheet off of the PMMA and put the baffle into the stand. Install the brace pole 1 After put the brace pole to the stand, use the screw 8 M4x12 to fix it. -
Page 16: Turning On The Tv
* In this manual, the OSD (On Screen Display) may be different from your an example to help you with the operation. Turning on the TV just after installation. . Connect power cord correctly. Press the SWITCH button on back of the TV. At this moment, the TV is switched to standby mode. Press the POWER button on the remote control or Turning on the TV . -
Page 17: Basic Function
Basic Function Basic Function Operation Menu 1.Press MENU button to open the main menu. Press VOL+/- button to select PIC., SOU., ADJ., SYS. , FUN. or TIME menu. 2.Press CH+/- button to select submenu, and press VOL+/- button to increase/decrease the value or select the setup. 3.Press MENU to return to the main menu. -
Page 18: System Menu
System Menu This TV set has three methods to set channels, which are respectively Automatic search, manual search In this section, how to use the remote control to set channel is explained. You can also use buttons on the TV set to set channel. Channel Type Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e., an antenna or a cable system). -
Page 19: Fine Tune
System Menu Fine Tune If the picture and/or sound are poor, try using the fine tune feature. Do not use this feature unless reception is poor. Repeat step 1-2, then press CH+/- buttons to select "Fine Tune" item. Press VOL-/+ buttons repeatedly to carry out fine tune, till the best picture and sound are obtained, then loosen the button. -
Page 20: Picture Quality Adjust Picture Quality Adjust
Picture Quality Adjust Picture Quality Adjust Picture Quality Adjust The TV menu gives you an overview of MENU you can select. Note: Depending on the input signal, one or more menu items may not be selectable. Press MENU and then use VOL+/- button to select the PIC. Menu. Press CH+/-button to select the desired items. -
Page 21: Sound Adjustment
Sound adjustment Sound adjustment Sound Adjust Sound can be adjusted for any input as follows: 1. Press MENU button and then use VOL+/- button to select the SOU.menu. 2. Press CH+/- button for desired option. 3. After your option is selected, press VOL+/- button to adjust. 4. -
Page 22: Adjustment Setup
Adjustment Setup Adjustment Setup Adjustment Setup In VGA and DVI input mode , H Position and V Position can be used to adjust the picture position. When VGA DVI input mode is set 1. Press MENU button on the remote controller and then use the VOL+/- to select the ADJ.menu. -
Page 23: Function Setup Function Setup
Repeat step 3 and 4 to select blue Screen between off or on. On is selected , and there is no signal to the TV for 2 minutes , the TV will be in standby condition . If Off is Haier will be on the screen . Menu Language English OSD Timeout... -
Page 24: Close Caption
Close Caption Closed captioning is a process which converts the audio portion of a television program into written words which then appear as subtitles on the television screen. Closed captions allow viewers to read the dialogue and narration of television programs. Using Closed Captions Captions are the subtitles of the dialogue and narration of television programs. - Page 25 Continue Parental Ratings for Movies previously shown in theaters: Movie Ratings : PG-13 NC-17 If you set PG-13 : G and PG movies will be available , PG-13, R, NC-17 and X will be blocked. Ratings for Television programs including made-for-TV movies : TV-Y TV-Y7 TV-G...
-
Page 26: Time Setup
Time Setup Time Setup If Off-time or On-time is intended in AV1/S-Video/YPbPr/YCbCr/VGA , follow the instructions as below: Clock Setting The clock will only work if the TV set is turned on or in standby. When the set is disconnect from the power supply or is turned off by the main power on the rear panel, the clock loses power and will need to be reset when the power is reconnected. -
Page 27: Lock Menu Options
Lock Menu Options Lock Menu Options - The TV has the function of security default lock. Password needs to be entered when the program lock mode is to be set. Lock Setup Press LOCK button on remote control, Password will appear on the screen. If password is correctly entered, the Lock set menu will be menu willl be entered. -
Page 28: Prog.num
Prog.Num Prog. Num is opted for setting up preset channel. Press CH+/- button to select Prog Num. Press VOL+/- button, to select channel number.(The item is not available except TV signal.) Source Lock Source Lock is opted to hinder external input modes, such as AV, S -Video and VGA. Press CH+/- button to select the option, and press VOL+/- button to display Source Lock menu. -
Page 29: Auto Adjustment
- RGB (PC) mode only; This function doesn`t work for RGB-DTV mode. - Automatically adjusts picture position and minimizes image shaking. - After adjustment, if the image is still not correct, your TV is functioning properly but needs further adjustment. - The Auto sync are not active in DVI mode. -
Page 30: Troubleshooting Checklist
No picture & No sound Picture OK & No sound The remote control doesn`s work Picture appears slowly after switching on No or poor color or poor picture Horizontal/vertical bars or picture shaking No output from one of the speakers Unusual sound from inside the TV 30 Plasma TV... -
Page 31: Maintenance
- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning. . Here`s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. -
Page 32: Product Specifications
Operating Temperature Range Operating Humidity Range Maximum Elevation Impedance Input consumption Speakers Size(WxHxD) (inches/mm) Weight (pounds/kg) The specifications shown above may be changed without notice for quality improvement. 32 Plasma TV 42EP24STV 41.3x3.4x26.1/1050x664x86 60.6/27.5 852x480(Dot) ~110/220 Volts , 50/60Hz 2x10W 4.3x21.9x2.4/110x556x62 2x5.5/2x2.5... - Page 33 V0.1 0090506987...