Schlage BE365 Programming/Operating Manual
Door lock
Hide thumbs
Also See for BE365:
- User manual ,
- Installation instructions manual (9 pages) ,
- User programming manual (5 pages)
Table of Contents
Advertisement
P515-549
BE365
FE575
FE595
Preset Codes
Programming Code: 123456
User Code A: 4321
User Code B: 5678
Example
Example
Preset User Codes
BE365, FE575, FE595
Programming/Operating Guide
Table of Contents
BE365 Features .......................................................2
Lock Operation ............................................2
Changing the Battery ...................................3
FE575 Features .......................................................4
Lock Operation ............................................4
Changing the Battery ...................................5
FE595 Features .......................................................6
Lock Operation ............................................6
Changing the Battery ...................................7
Programming for All Models ....................................8
Keeping Your Lock Secure .....................................10
Key Override ..........................................................10
Troubleshooting Guide ...........................................11
Emergency Lock Override .....................................12
S/N: 1-00000000
Model: BE365
Preset Programming Code
Serial Number
Lock Series
Place Label Here
Advertisement
Table of Contents
Related Manuals for Schlage BE365
Summary of Contents for Schlage BE365
-
Page 1: Table Of Contents
BE365, FE575, FE595 Programming/Operating Guide P515-549 Table of Contents BE365 Features ............2 Lock Operation ..........2 Changing the Battery ........3 FE575 Features ............4 BE365 Lock Operation ..........4 Changing the Battery ........5 FE595 Features ............6 Lock Operation ..........6 Changing the Battery ........7 Programming for All Models ........8... -
Page 2: Be365 Features
E. Inside Thumbturn 2. Use to program the lock. (See page 8.) Extends and retracts the deadbolt from the inside. BE365 Lock Operation To Retract the Deadbolt To Extend the Deadbolt a. Enter a valid four-digit user code. a. Push button. -
Page 3: Changing The Battery
BE365 Lock Operation Continued Locked - Deadbolt Extended Unlocked - Deadbolt Retracted Locked - Unlocked - User code No user code Deadbolt required required for entry for entry BE365 Changing the Battery For low battery indications, see page 11. NOTE: Replace with premium 9V alkaline battery. -
Page 4: Fe575 Features
FE575 Features Button B. Keypad C. Key Override D. Outside Knob/Lever E. Inside Knob/Lever Button C. Key Override (See page 10.) 1. Press to turn on backlight. 2. Press to clear an incorrect code entry. D. Outside Knob/Lever B. Keypad Always rotates. -
Page 5: Changing The Battery
FE575 Changing the Battery For low battery indications, see page 11. NOTE: Replace with premium 9V alkaline battery. Reverse steps to assemble lock. -
Page 6: Fe595 Features
FE595 Features Button B. Keypad C. Key Override D. Thumbturn E. Outside Knob/Lever F. Inside Knob/Lever Button D. Thumbturn Switches between locked and unlocked. 1. Press to turn on backlight. 2. Press to clear an incorrect code entry. (See below.) B. -
Page 7: Changing The Battery
FE595 Lock Operation Continued To Unlock the Lock (While thumbturn is in locked position) a. Enter a valid four-digit user code. (See note.) b. The button will fl ash green c. Rotate outside knob/lever within fi ve seconds to open door. d. -
Page 8: Keypad Codes
Example Example • Won't program lock Schlage Button (on front of lock) • Lights orange while in programming mode. • Flashes green when programming is successful. • Lights red when there is an error. Retry steps or see troubleshooting guide on page 11. - Page 9 IMPORTANT: Lock will be reset to the preset programming and user codes. All existing user codes and current programming code will be erased. 1. Disconnect the battery. (For FE575, see page 3. For FE595, see page 5. For BE365, see page 7.) 2. Press and release 3. Reconnect the battery and wait until is no longer lit.
-
Page 10: Keeping Your Lock Secure
Rotate knob/lever. back to relock. remove key. 270° 270° Key cannot be removed in this position. BE365 Only NOTE: Key will both extend and retract deadbolt. Rotate key and Push key into Insert key. Rotate key 90°. thumbturn 90°. thumbturn. -
Page 11: Troubleshooting Guide
None seconds, then replace battery. numbers are pressed. For FE575, see page 3. For FE595, see page 5. For BE365, see page 7. Battery is low and should be replaced. There is a delay before unlock High/Low, Red then For FE575, see page 3. -
Page 12: Emergency Lock Override
Emergency Lock Override If the outside thumbturn does not freely rotate or the lock is malfunctioning, you can enable the emergency override feature. When emergency override is engaged, a key must be used to extend/retract the deadbolt. a. Remove screws and thumbturn assembly. b.
Need help?
Do you have a question about the BE365 and is the answer not in the manual?
Questions and answers
Model BE65 does not allow dead bolt to lock when Schlage button is pressed after wire harness was disconnected
If the Schlage BE365 deadbolt does not lock when the Schlage button is pressed after the wire harness has been disconnected, it may need to be reset. To reset the lock:
1. Disconnect the battery.
2. Press the Schlage button.
3. Reconnect the battery.
4. Press and hold the Schlage button until it lights green and the lock beeps.
5. Enter a default code to confirm the reset.
This process restores the lock to factory settings, which may resolve the issue.
This answer is automatically generated
Model BE65. After replacing battery, the schlage button blinked green after putting in code but handle doesn't seem to be attached to deadbolt. Handle just turns but no control of dead bolt.
If the Schlage BE365 handle turns without controlling the deadbolt after replacing the battery, the lock may be malfunctioning. You can try the following steps:
1. Check Installation – Ensure the inside components are correctly installed.
2. Factory Reset – Perform a reset by:
- Disconnecting the battery.
- Pressing the Schlage button.
- Reconnecting the battery while holding the Schlage button until it lights green and beeps.
3. Emergency Lock Override – If the issue persists, enable the emergency override:
- Remove screws and the thumbturn assembly.
- Disconnect and remove the battery.
- Use a screwdriver to rotate the slot inside.
If the problem continues, refer to the manual for troubleshooting or consider replacing the lock.
This answer is automatically generated
Is their a “secret” code for police and emergency personnel in case of an accident and they need entry into the home?
How can you disable key bypass
Do we need to enter the user codes given and then change them to preferred codes?
No, the Schlage BE365 lock comes preset with two unique default User Codes. You can use these default codes to unlock the lock initially. You do not need to enter and change them unless you prefer to use your own custom codes.
This answer is automatically generated
My lock will lock as intended but will unlock with out using a code only have to push the Schlage button.
The Schlage BE365 lock may unlock without using a code because the internal mechanism is not staying engaged after locking. This could be due to a mechanical failure, misalignment, or worn internal parts. Pressing the Schlage button is supposed to engage the lock for code entry, but if the bolt disengages freely without requiring a code, it indicates the locking mechanism is not functioning correctly. This may require disassembly and inspection of the internal components or replacing worn parts.
This answer is automatically generated