Page 2
MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.
INTRODUCTION Foreword We are proud to offer the Model G0538 Oscillating Spindle Sander. This machine is part of a grow- ing Grizzly family of fine woodworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s com-...
Machine Data Sheet Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0538 1/3 HP OSCILLATING SPINDLE SANDER Product Dimensions: Weight... 34 lbs. Length/Width/Height... 20 x 14 x 11-1/2 in. Foot Print (Length/Width)... 20 x 14 in.
Page 6
The information contained herein is deemed accurate as of 11/29/2005 and represents our most recent product specifications. Model G0538 Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 2 OF 2 G0538 Oscillating Spindle Sander...
B. Table C. Sanding Sleeve D. Spindle Washer E. Throat Plate G. Accessory Storage Area H. ON⁄OFF Paddle Switch with Lockout Key G0538 Oscillating Spindle Sander Identification Figure 1. Identification. Sander Body 5-15 Plug and Power Cable ⁄ " Dust Port (not shown)
Wear protective hair covering to con- tain long hair and wear non-slip footwear. 6. NEVER OPERATE MACHINERY WHEN TIRED, OR UNDER THE INFLUENCE OF OPERATING DRUGS OR ALCOHOL. Be mentally alert at all times when running machinery. OPERATING MACHINERY. G0538 Oscillating Spindle Sander...
Page 9
Follow instructions for lubricating and changing accessories. 16. MAKE SURE GUARDS ARE IN PLACE AND WORK CORRECTLY BEFORE USING MACHINERY. G0538 Oscillating Spindle Sander 17. REMOVE WRENCHES. Make a habit of checking for keys and adjusting wrenches before turn- ing machinery ON.
UNATTENDED MACHINE. Never leave the machine running unattended. Like all machines there is danger associ- ated with the Model G0538. Accidents are frequently caused by lack of familiarity or failure to pay attention. Use this machine with respect and caution to lessen the pos- sibility of operator injury.
DO NOT connect the machine to the power source until instructed to do so. Amperage Draw The Model G0538 motor draws the following amps under maximum load: Motor Draw ... 4 Amps Circuit Recommendations...
Wrench ⁄ " ... 1 Unpacking The Model G0538 was carefully packed when it left our warehouse. If you discover the machine is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice.
OMMEND that you read books, trade maga- zines, or get formal training before begin- ning any projects. Regardless of the con- tent in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training. G0538 Oscillating Spindle Sander ⁄...
Tug the hose to ensure it does not come off. Figure 6. Dust port. DO NOT operate the Model G0538 without an adequate dust collection system. This saw creates substantial amounts of wood dust while operating. Failure to use a dust collec- tion system can result in respiratory illness.
(Figure 7) from the paddle switch. Figure 7. Removing key to disable switch. Sleeve Installation The G0538 Oscillating Spindle Sander comes with six different-sized sanding drums and sleeves. Always refer to the table below when determing the appropriate throat plate, sanding drum, and spindle washer size for a particular sleeve.
Turn on the spindle sander and allow it to reach full speed. Using both hands, guide the workpiece against the sanding sleeve in a right-to-left direction, as shown in Figure 10. DO NOT force the workpiece against the sanding sleeve. Figure 10. Sanding. G0538 Oscillating Spindle Sander...
Belt Cleaners. ® G0538 Oscillating Spindle Sander H5430-H5459 Sanding Sleeves Grizzly stocks a wide variety of aluminum oxide sanding sleeves of varying sizes and grits. All our 4½" long sanding sleeves are available in 60 to 150 grit and from in packs of three.
Clean⁄vacuum dust buildup from inside the sander body and off the motor. -16- Cleaning Cleaning the Model G0538 is relatively easy. Follow the Sleeve Installation instructions on Page 15, taking special care to clean every area thoroughly. However, sawdust and other particles can also work their way under the rotation mark plate.
Sanding surfaces 1. Too much pressure against sleeve. clog quickly 2. Sanding softwood. burn. G0538 Oscillating Spindle Sander Troubleshooting Possible Solution 1. Check power line voltage and correct if necessary. 2. Inspect all motor connections for loose or open connec- tions.
Page 20
1. Dry stock properly before sanding. 2. Use different stock. Or, accept the characteristics of the stock and plan on cleaning⁄replacing belts⁄discs fre- quently. 1. Move workpiece against direction of spindle rotation (right-to-left). 2. Start workpiece on a trailing corner. G0538 Oscillating Spindle Sander...
SAFETY PADDLE SWITCH WIRES TO 110V POWER SUPPLY G0538 Oscillating Spindle Sander Wiring Diagram �������� ����� ������ ����� ����� ������������ Disconnect power from machine before perform- ing any electrical ser- vice. Failure to do this will result in a shock haz-...
MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels. G0538 Oscillating Spindle Sander...
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Need help?
Do you have a question about the G0538 and is the answer not in the manual?
Questions and answers