Stanley DL07 User Manual
Hydraulic
Hide thumbs
Also See for DL07:
- Operation and service manual (23 pages) ,
- Service manual (22 pages) ,
- User manual (16 pages)
Related Manuals for Stanley DL07
Summary of Contents for Stanley DL07
- Page 1 DL07 HYDRAULIC DRILL afety peratiOn and aintenance USer ManUaL © 2010 Stanley Black & Decker, Inc. New Britain, CT 06053 U.S.A. 49234 12/2012 Ver. 7...
-
Page 2: Declaration Of Conformity
Provisiones especiales: Disposizioni speciali: Representative in the Union: Patrick Vervier, Stanley Dubuis 17-19, rue Jules Berthonneau-BP 3406 41034 Blois Cedex, France. Vertreter in der Union/Représentant dans l’union/Representante en la Union/Rappresentante presso l’Unione Done at/Ort/Fait à/Dado en/Fatto a Stanley Hydraulic Tools, Milwaukie, Oregon USA... -
Page 3: Table Of Contents
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest authorized and certified dealer, call Stanley Hydraulic Tools at the number listed on the back of this manual and ask for a Customer Service Representative. -
Page 4: Safety Symbols
Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. 4 ► DL07 User Manual... -
Page 5: Safety Precautions
Do not operate a damaged, improperly adjusted, or the space provided in this manual. incompletely assembled drill. The model DL07 Hydraulic Drill will provide safe and • Never wear loose clothing that can get entangled in dependable service if operated in accordance with the the working parts of the tool. -
Page 6: Tool Stickers & Tags
OPERATION MANUAL. OPERATION MANUAL. TAG TO BE REMOVED ONLY BY TAG TO BE REMOVED ONLY BY TOOL OPERATOR. TOOL OPERATOR. SEE OTHER SIDE SEE OTHER SIDE SAFETY TAG P/N 15875 (Shown smaller then actual size) 6 ► DL07 User Manual... -
Page 7: Hose Type
HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS. -
Page 8: Hose Recommendations
HOSE RECOMMENDATIONS 8 ► DL07 User Manual... -
Page 9: Htma Requirements
2000 psi 2000 psi 2000 psi (at the power supply outlet) (172 bar) (138 bar) (138 bar) (138 bar) (138 bar) NOTE: These are general hydraulic system requirements. See tool specification page for tool specific requirements DL07 User Manual ◄ 9... -
Page 10: Operation
(CC) OPERATION come dull. The Stanley HD08 should be used for this application. The DL07 can be configured to run on OC or CC circuits. 1. Determine the system type. 2. Remove the hex plug (81) from the spring cap. -
Page 11: Cold Weather Operation
Each bit selected must always be too large to thread and jam into an existing hole; otherwise the bit may break and endanger the operator. DL07 User Manual ◄ 11... -
Page 12: Tool Protection & Care
This can cause damage to internal seals. • Always replace hoses, couplings and other parts with replacement parts recommended by Stanley Hydraulic Tools. Supply hoses must have a mini- mum working pressure rating of 2500 psi/172 bar. 12 ► DL07 User Manual... -
Page 13: Troubleshooting
Refer to Operation section for correct fluid/ hot. circuit specifications. Oil leak at motor cap face. Fasteners loose. Refer to Service Manual. Face O-ring worn or missing. Replace as required. Motor cap/main housing dam- Replace as required. aged. DL07 User Manual ◄ 13... -
Page 14: Specifications
Declared vibration emission value in accordance with EN 12096 Measured vibration emission value: a 1.4 m/sec² Uncertainty: K 0.35 m/sec² Values determined according to ISO 8662-1, ISO 5349-1,2 14 ► DL07 User Manual... -
Page 15: Accessories
15/16 inch dia × 18 inch Carbide Tipped Auger Bit (22 inch OAL) ..............27863 1-1/16 inch dia × 18 inch Carbide Tipped Auger Bit (22 inch OAL) ..............27864 13/16 inch dia × 36 inch Carbide Tipped Auger Bit (48 inch OAL) ..............27869 DL07 User Manual ◄ 15... -
Page 16: Dl07 Parts Illustration
DL07 PARTS ILLUSTRATION 16 ► DL07 User Manual... -
Page 17: Dl07 Parts List
MOTOR CAP ASSY (INCLUDES 1 BUSHING ITEM 15 & 2 DOWEL PINS ITEM 6) 20782 IDLER SHAFT 03972 3/8 NPT FLUSHFACE COUPLER BODY PART OF SET 03971 (PARKER) OR 47436 (AEROQUIP) FOR DL07552S, 552SUP, 572S DL07 User Manual ◄ 17... - Page 18 Stanley Hydraulic Tools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www.stanleyhydraulic.com IMPORTANT To fill out a Product Warranty Recording form, and for information on your warranty, visit Stanleyhydraulic.com and select the Warranty tab.
Need help?
Do you have a question about the DL07 and is the answer not in the manual?
Questions and answers