Related Manuals for D.T. System Micro-iDT PLUS Series
Summary of Contents for D.T. System Micro-iDT PLUS Series
- Page 1 SUPER TRAINER SUPER TRAINER Micro-iDT™ PLUS SERIES Electronic Dog Trainer Owner’s Manual • Micro-iDT™ PLUS (One Dog Trainer with Add-On Capability)
- Page 2 NOTICE! According to how you use your transmitter, transmitting range might be much different. You will have more range if you use your transmitter apart from your body as follows: Maximum Range Typical Range Minimum Range...
-
Page 3: Table Of Contents
TABLE OF CONTENTS • Table of Contents ........... 3 • Introduction ............ 4 • Package Contents .......... 5 • Model Features ..........5 • Parts & Functions ........... 6 • SmartLED............10 • Charging the Collar Batteries ......11 • Turning ON and OFF........ -
Page 4: Introduction
The automatic safety shut-off feature stops the stimulation after 8 seconds to prevent accidental or prolonged stimulation. Thanks again for choosing D.T. Systems to help bring out the best in your best friend! IMPORTANT NOTE: Please read this owner’s manual in its entirety before operating this unit. -
Page 5: Package Contents
PACKAGE CONTENTS • Transmitter* • Collar Receiver • Rechargeable Batteries for the Collar (already installed in collar unit) • Battery Charger • Splitter/Adaptor Charging Cable • Test Light • Owner’s Manual *9-volt transmitter battery not included MODEL FEATURES • Digital Technology •... -
Page 6: Parts & Functions
PARTS & FUNCTIONS Antenna Collar Selecting Switch Intensity Selection Dial Indicator Light Momentary “Nick” Stimulation Vibration Button Button Continuous Stimulation Button Magnet Indicator Model (Red Mark) Number Battery Cover (back side) Transmitter Intensity Selection Dial The Intensity Selection Dial can be set from level 1 to level 16 to find the exact stimulation level for your dog (see page 16). - Page 7 PARTS & FUNCTIONS Transmitter Antenna Be sure to check that the Antenna is securely fastened to the Transmitter before each use. Hand-tightened only. Be careful when screwing the Antenna into the Transmitter. Over-tightening the Antenna can cause damage to the Antenna or the antenna mount. Magnet Indicator (Red Mark) The Red Mark indicates the Magnet location and is used to turn the Collar Receiver ON/...
-
Page 8: Collar Receiver
PARTS & FUNCTIONS Collar Belt with Embedded Re- ceiver Antenna Contacts Magnetic Switch Battery Charging Indicator Receptacle (Red Mark) SmartLED Indicator Light Collar Receiver Collar SmartLED Indicator Light When the Collar Receiver is turned on, the SmartLED light will flash green once every two seconds if the rechargeable battery has 51% to 100% charge left and flash red once every two seconds if it has 21% to 50% charge left. - Page 9 PARTS & FUNCTIONS Magnetic Switch Indicator (Red Mark) The Red Mark indicates the location of the Magnet Switch in the Collar Receiver and is used to turn the Collar Receiver ON/OFF and for ID Programming. Collar Belt with MAXX-Range™ Antenna The embedded Collar Antenna is woven into the Collar Belt and runs the entire length of the belt.
-
Page 10: Smartled
*Charging Error - If the SmartLED has a long blink every other second while charging, the rechargeable battery pack will need to be replaced. New batteries may also initially give an error light. Contact D.T. Systems if the problem persists after a few charging sessions. -
Page 11: Charging The Collar Batteries
CHARGING THE COLLAR BATTERIES Micro-iDT™ PLUS Series collars are equipped with rechargeable Nickel Metal Hydride (NiMH) batteries, which are not memory sensitive and do not require depletion before recharging. Although batteries come partially charged from the factory, it is recommended that they are given a full charge (about 12 hours) before initial use. -
Page 12: Turning On And Off
TURNING ON AND OFF The Transmitter is always in a permanent sleep state. It is only ON when a button is being pressed and does not need to be turned off by the user. Turning the Collar Receiver ON 1. Hold the Magnet Indicator (Red Mark) on the Transmitter directly on the Magnet Switch Indicator (Red Mark) on the Collar Receiver. -
Page 13: Testing
TESTING NOTE: Before testing, make sure that both units are fully charged and the Collar Receiver is “ON”. To Test the Electronic Stimulation 1. Place the tester firmly on the contacts of the Collar Receiver. 2. Set the intensity (note - an intensity level setting of 4 or less might not be enough to light the tester). -
Page 14: Programming
PROGRAMMING When adding an “Add-On” collar, the collar will need to be programmed to the transmitter. If your current collar unit is not responding to the transmitter, it may also need to be reprogrammed to the transmitter. 1. Select the desired Collar Selecting Switch position on the transmitter. -
Page 15: Properly Fitting The Collar
PROPERLY FITTING THE COLLAR NOTE: Proper collar tightness and position are very important to insure safe and consistent collar use. All electronic collars need to be very snug around the dog’s neck to work properly. They must be just tight enough to allow the “contacts”... -
Page 16: Setting The Intensity Level
SETTING THE INTENSITY LEVEL It is very important to set the correct intensity level on your Micro-iDT PLUS Training System before beginning your training sessions to provide the proper level of stimulation without over-stimulating your dog. 1. Place the Intensity Selection dial so that the system is set on Level 1. -
Page 17: Maintenance
MAINTENANCE Micro- It is very important to periodically clean your iDT™ PLUS Series systems maximum performance. Regular cleaning will also lengthen the life of your unit. Micro-iDT™ • Clean the PLUS Series collar box with lukewarm water and a mild anti-bacterial soap. •... -
Page 18: Important Safety Notes
IMPORTANT SAFETY NOTES • Before training, your dog should be examined by a veterinarian to assure that your dog is in good health. • Never leave your dog unattended with the unit on. Since no electronic device is perfect, there is a very slight possibility that your dog may receive an unintentional electric stimulation. -
Page 19: Warranty
WARRANTY All Micro-iDT™ PLUS Trainer systems have a one year parts and labor warranty effective from the original date of purchase. A copy of the original sales receipt is required to validate the date of purchase. The Micro-iDT™ PLUS Trainer has been made with State of the Art equipment. Any fine adjustment should be performed only by D.T. -
Page 20: Contact Information
2872 Walnut Hill Lane Dallas, Texas 75229 Tel: (214) 350-9446, (888) 588-8364 Fax: (214) 350-7847 Website: www.dtsystems.com E-mail: customerservice@dtsystems.com 1-iDT PLUS 2011.06.07 Printed in Korea...
Need help?
Do you have a question about the Micro-iDT PLUS Series and is the answer not in the manual?
Questions and answers