Page 1
/ VOLUME PHONES SPEED AMP + FX EFFECT STORE FX ONLY VOLUME COPY FUNCTION TUNER PEDAL CONFIGURE BASS EQ PRESENCE NOISE G. REVERB COMPR. DELAY MODUL. BYPASS/TUNER User Manual X V-AMP LX1-X Ultra-Flexible Modeling Amp/Multi-Effects Processor with Integrated Expression Pedal...
X V-AMP LX1-X User Manual Table of Contents Important Safety Instructions ........3 Legal Disclaimer ............. 3 Limited Warranty ............3 1. Introduction ............... 5 1.1 Before you get started ............5 2. Control Elements and Connectors ......5 2.1 Basic advice on using the controls ....... 5 3.
A list of authorized resellers can dangerous voltage inside the moving the cart/apparatus be found on BEHRINGER’ s website behringer. com under enclosure - voltage that may be suffi cient to constitute a combination to avoid “Where to Buy”, or you can contact the MUSIC Group offi ce risk of shock.
X V-AMP LX1-X User Manual • connection or operation of the unit in any way “Support” at behringer. com. If your country is not (3) This warranty does not detract from the seller’ s listed, please check if your problem can be dealt with...
Otherwise, you may void your warranty. “EFFECTS PROCESSOR”). Always make sure your X V-AMP gets enough air flow and never put it near the By keeping TAP depressed, 2nd FUNCTION (13) is activated. By doing this, heating or other heat-emitting equipment to avoid damage to the device.
Page 6
2 seconds and then powering up the You get to the second-layer effects (gray) by keeping the TAP key depressed X V-AMP (i.e. you start the procedure when your X V-AMP is off). while you are turning the FX/AMPS control; the 2nd FUNCTION LED lights (3) NOISE G.
Page 7
(e. g. volume, effect intensity etc.). See also (10) . (19) LINE OUT/PHONES. You can take the audio signal of your X V-AMP at the When editing effect blocks, ADJUST lets you access the second function layer for parameter settings.
(according to your own needs and speaker and amp LOUDNESS: Increasing bass and highs desires) will be fed to the outputs. To optimally adjust your X V-AMP to various simulations) PRESENCE: Accentuation of upper mids, lowering of bass tones studio and live situations, you can select one of the 9 possible configurations.
Vox successfully implemented by means Editing presets on your X V-AMP is quick and easy to do. One way to do this is to of “revolutionary” bass and treble controls. Brian May and U2’s The Edge are call up a preset of your choice and then modify it according to your own taste.
If you hook The X V-AMP takes a half of the time interval measured between the taps on TAP. up a decent tube amp to your X V-AMP (e. g. the BEHRINGER AC112), with this The echo velocity doubles.
Tri Stereo Chorus, with its 12 (!) voices that are modulated against each other. The X V-AMP offers you this Ambience: short room simulation without reverb tail.
In doing so, the X V-AMP is switched into bypass mode. Use ADJUST to modify bypass volume. The input of your BEHRINGER X V-AMP is a mono 1/4" TS connector. The line out/headphone output comes as 1/4" TRS stereo connector. The line output works 7.1 Tuning your guitar...
Shipping weight approx. 4.40 lbs / 2 kg Line/Headphone Output BEHRINGER constantly strives to maintain the highest quality standards. Modifications may be made, Type 1/4" TRS stereo connector, balanced if necessary, without prior notice. The specifications and appearance of the equipment may therefore differ from those listed or illustrated.
Page 14
X V-AMP LX1-X User Manual FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION X V-AMP LX1-X MUSIC Group Services US Inc. Responsible Party Name: 18912 North Creek Parkway, Address: Suite 200 Bothell, WA 98011, Phone: +1 425 672 0816 Phone/Fax No.: Fax: +1 425 673 7647 X V-AMP LX1-X complies with the FCC rules as mentioned in the following paragraph:...
Need help?
Do you have a question about the X V-AMP and is the answer not in the manual?
Questions and answers