Operating Your Ceiling Fan - Emerson OLYMPIA KF100AP00 Owner's Manual

STANDARD ON-OFF WALL
SWITCH OR OPTIONAL SW113
WALL CONTROL
BLACK
TO
(HOT)
120-
VOLT
SUPPLY
WHITE
GROUND
TWO-CONDUCTOR
CABLE (WITH
GROUND)
GREEN WIRE (GROUND)
FROM HANGER BALL AND
HANGER BRACKET
Figure 14
3. Push the wires and connectors up into
the outlet box while inserting the receiv-
er fully into the hanger bracket. Position
the antenna wire on top of the receiver.
4. Screw the two 1-1/4" threaded studs
(supplied) into the tapped holes in the
hanger bracket (Figure 13).
5. Lift the ceiling cover up to the threaded
studs and turn until the studs protrude
through the holes in the ceiling cover
(Figure 15).
6. Secure the ceiling cover in place by
sliding lockwashers (supplied) over the
threaded studs and installing the two
knurled knobs (supplied). (Figure 15).
Tighten the knurled knobs securely
until the ceiling cover fits snugly against
the ceiling.
CEILING
COVER
THREADED
LOCKWASHER
STUD (2)
(2)
KNURLED
KNOB (2)
Figure 15
BLACK
BLACK
WHITE
WHITE
BLACK
BLUE WHITE
BLACK
BLUE
WHITE
HANGER BALL
WARNING
!
To avoid possible fire or shock, make
sure that the electrical wires are
completely inside the outlet box and
not pinched between the ceiling
cover and the ceiling.
7. Screw an A19 100-watt (maximum)
medium base bulb into the light fitter
socket (Figure 16).
8. Place the lower glass in the lower ring
assembly (Figure 16). Unscrew four
bracket mounting screws from the four
lower ring posts.
BRACKET MOUNTING
SCREW (4)
LOWER RING
BRACKET
SOCKET
POST
LOWER RING
ASSEMBLY
LOWER GLASS
Figure 16
10
9. Securely grasp one of the lower ring
posts and raise the lower ring up to one
of the lower ring brackets. Secure the
lower ring post to the lower ring brack-
et using a bracket mounting screw
(Figure 16). Grasp the opposite post
and secure the post to the opposite
bracket using a bracket mounting
screw.
10. Secure the remaining two lower ring
posts to the lower ring brackets using
bracket mounting screws.
NOTE: It may be necessary to slightly
adjust the position of the remaining
two brackets so they align with the
posts. After the lower ring has been
mounted, check that the four bracket
mounting screws securing the four
brackets to the switch housing assem-
bly are tight.
Installation of
Storage Bracket
A storage bracket is supplied with the
remote control for holding the transmitter
when not in use. If you desire to use the
bracket, use the two screws (supplied)
and install it on a wall that is away from
excess heat or humidity. When installing,
orient the bracket so that the tab is at the
top and away from the wall (Figure 17).
REMOTE CONTROL
TRANSMITTER
TAB
FAN/OFF HI
FOR/REV MED
LIGHT LOW
DIMMER
STORAGE
BRACKET
®
Figure 17
Operating Your
Ceiling Fan
IMPORTANT
Fan installation must be completed,
including the installation of the fan
blades, before testing of the remote
control.
Your remote control has full control of your
fan and light.
1. Restore electrical power to the outlet
box by turning the electricity on at the
service panel.
2. To set the desired fan speed, press the
HI, MED, or LOW buttons to operate
your fan on high, medium, or low speed
(Figure 18).
3. To turn your fan off, press the FAN/OFF
button.
4. To change the airflow direction of the
fan blades, press the FOR/REV button.
The direction the fan blades turn will
change each time the FOR/REV button
is pressed.
5. To set the level of light brightness,
press and hold the LIGHT DIMMER
button. The light brightness will contin-
ue to increase then decrease while the
button is held down. When the light is
at the desired brightness, release the
button.
6. To turn the light ON and OFF, press
and release the LIGHT DIMMER but-
ton. The light will turn ON at the light
level previously set (see step 5).
Red light should turn on when any but-
ton is pressed. If the light does not
come on, replace the battery.
11