Panasonic PT-VW345NZ Specifications
Lcd projector
Hide thumbs
Also See for PT-VW345NZ:
- Operating instructions manual (140 pages) ,
- Operating instructions (functional manual) (140 pages)
Subscribe to Our Youtube Channel
Related Manuals for Panasonic PT-VW345NZ
Summary of Contents for Panasonic PT-VW345NZ
- Page 1 PT-VW345NZ P ro d u c t N u m b e r : LCD Projectors P ro d u c t N a m e : As of October 2013. Specifications and appearance are subject to change without notice.
-
Page 2: Specifications
PT-VW345NZ LCD Projectors Specifications Main unit Power supply 100 V, 100 –240 V AC, 50/60 Hz Power consumption 100–120 V: 300 W, 220–240 V: 280 W (0.4 W when Standby mode set to Eco* , 5 W when Standby mode set to... - Page 3 PT-VW345NZ LCD Projectors COMPUTER (RGB) 2IN/ 1OUT D-sub HD 15-pin (female) × 1 R, G, B (input/output selectable using on-screen menu) G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms; B, R: 0.7 Vp-p, 75 ohms; HD/VD, SYNC: high impedance, TTL (positive/negative) NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
-
Page 4: Microsoft ® Windows ® Xp
PT-VW345NZ LCD Projectors Wireless Manager ME 6.0.2 system requirements To use network functions, a PC is required that meets the conditions given below. Microsoft ® Windows Professional 32-bit, Home Edition 32-bit, Tablet PC ® Edition 2005 32-bit Windows Vista : Ultimate 32-bit/64-bit, Business 32-bit/64-bit, Home ®... - Page 5 PT-VW345NZ LCD Projectors Dimensions unit : mm (inch) NOTE: This illustration is not drawn to scale. (2-15/32) 176 (6-15/16) 352 (13-27/32) Terminals Computer 1 input Computer 2 input / computer 1 output HDMI input USB B connector USB A connector...
-
Page 6: Standard Setting-Up Position
PT-VW345NZ LCD Projectors Standard setting-up position NOTE: Illustrations show the projector installed using optional ceiling mount bracket ET-PKV100H and bracket ø38 assembly ET-PKV101B. (1-1/2) This illustration is not drawn to scale. Upper edge of projected image 153.9 125.5 (5-1/16) (4-15/16) -
Page 7: Installable Angle
PT-VW345NZ LCD Projectors Projection distance for 16:9 aspect ratio screen unit: meters (feet) Projection size Projection distance [L] Height from the edge of screen to center of lens [ H ] [diagonal] Min [wide] Max [telephoto] 0.76 m 30˝ (2.5) (3.9) -
Page 8: List Of Compatible Signals
PT-VW345NZ LCD Projectors List of compatible signals The signals that can be input to this projector are shown in the table below. Horizontal scanning fre- quencies of 15 kHz to 80 kHz (15 kHz to 100 kHz for RGB signals), vertical scanning frequencies of 50 Hz to 120 Hz (50 Hz to 100 Hz for RGB signals), and a dot clock of 162 MHz maximum imum for RGB signals) can be input. - Page 9 PT-VW345NZ LCD Projectors Display mode Display Scanning frequency Dot clock Format resolution frequency (dots)* (kHz) (kHz) (MHz) 1280 × 768 60.3 74.9 102.3 HDMI/RGB 1280 × 768 68.6 84.8 117.5 41.2 50.0 69.9 1280 × 800 1280 × 800 49.7 60.0...
-
Page 10: Serial Connector
PT-VW345NZ LCD Projectors Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, com- mands must be input through communication software, based on the format and satisfying the commu- nication conditions shown below. Pin assignments and signal names... -
Page 11: Cable Specifications
PT-VW345NZ LCD Projectors Cable specifications Projector PC (DTE) Control commands < > r < > r Power on (standby mode on) – – Power off (standby mode off) – – Input signal selection IIS:<input si gnal> IIS:<input signal> – –... -
Page 12: Status Request Commands
HD1 = HDMI, RG1 = computer 1, RG2 = computer 2, NWP = network <input signal> PA1 = memory viewer, MG1 = panasonic application, MV1 = Miracast, VID = video, SVD = S-Video 000 = power off (standby mode off), 001 = power on (standby mode on) <power condition>... - Page 13 PT-VW345NZ LCD Projectors Notes on projector placement and operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. Never place objects on top of the projector while it is operating. Make sure there is the unobstructed space as shown below or more around the projector’s exhaust openings.
-
Page 14: Operating The Projector Continuously
PT-VW345NZ LCD Projectors Operating the projector continuously If the projector is to be operated continuously 12 hours or more, lamp replacement cycle duration becomes shorter. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods (one hour or less).
Need help?
Do you have a question about the PT-VW345NZ and is the answer not in the manual?
Questions and answers