Table of Contents
Advertisement
the fuel reserve tripmeter manually, it
will reset itself automatically and the
display will return to the prior mode af-
ter refueling and traveling 5 km (3 mi).
NOTE:
The display cannot be changed back to
"TRIP F" after pushing the "RESET"
button.
Fuel meter
With the key in the "ON" position, the
fuel meter indicates the amount of fuel
in the fuel tank. The display segments
of the fuel meter disappear towards "E"
(Empty) as the fuel level decreases.
When the fuel level reaches the bottom
segment near "E", the fuel level warn-
ing indicator and the bottom segment
will flash. Refuel as soon as possible.
Coolant temperature meter
With the key in the "ON" position, the
coolant temperature meter indicates
the temperature of the coolant. The
coolant temperature varies with chang-
es in the weather and engine load. If
the top segment and coolant tempera-
ture warning indicator flash, stop the
INSTRUMENT AND CONTROL FUNCTIONS
vehicle and let the engine cool. (See
page 6-40.)
CAUTION:
Do not operate the engine if it is
overheated.
Oil change indicator "OIL"
This indicator flashes at the initial 1000
km (600 mi), then at 5000 km (3000 mi)
and every 5000 km (3000 mi) thereafter
to indicate that the engine oil should be
changed.
After changing the engine oil, reset the
oil change indicator. (See page 6-13.)
If the engine oil is changed before the
oil change indicator comes on (i.e. be-
fore the periodic oil change interval has
3-7
been reached), the indicator must be
reset after the oil change for the next
periodic oil change to be indicated at
the correct time. (See page 6-13.)
The electrical circuit of the indicator can
be checked according to the following
procedure.
1. Set the engine stop switch to "
and turn the key to "ON".
2. Check that the indicator comes on
for a few seconds and then goes
off.
ECA10020
3. If the indicator does not come on,
have a Yamaha dealer check the
electrical circuit.
NOTE:
The oil change indicator may flash
when the engine is revved with the
scooter on the centerstand, but this
does not indicate a malfunction.
V-belt replacement indicator
"V-BELT"
This indicator flashes every 20000 km
(12500 mi) when the V-belt needs to be
replaced.
The electrical circuit of the indicator can
be checked according to the following
2
"
3
4
5
6
7
8
9
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
Need help?
Do you have a question about the MAJESTY 400 and is the answer not in the manual?
Questions and answers
How can I reset the v-belt indicator
To reset the V-belt indicator on a Yamaha Majesty 400, follow these steps:
1. Remove the cover labeled "Cen" using a pointy tool, such as a flathead screwdriver. Push in the centerpiece of the quick fasteners, then use your fingernails to pull them out.
2. Take note of how the cover fits before removing it completely.
3. Turn the bike on and ensure the kill switch is in the "Run" position.
4. Release the parking brake if it is engaged.
5. Follow the remaining steps in the owner's manual (page 7-78) to complete the reset process.
This will clear the V-belt replacement indicator from the display.
This answer is automatically generated
Como se prende tiene el botón pero lo aprieto y no hace nada
If the Yamaha Majesty 400 does not respond when the start button is pressed, try the following steps:
1. Make sure only one immobilizer key is near the main switch. Multiple keys may cause signal interference and prevent the engine from starting.
2. Try starting the engine using standard keys (non-immobilizer). If the engine starts, turn it off and try again with the standard keys.
3. If the standard keys do not start the engine, have the vehicle checked by a Yamaha dealer.
If an error code appears on the multi-function display, the vehicle should be inspected as soon as possible to avoid engine damage.
This answer is automatically generated
location of main electrical circuit breaker for 2008 Yamaha majesty 400