Memory Mode; Troubleshooting And Special Indications; Technical Specifications - ReliOn Digital Temple Thermometer Instructions For Use

Memory Mode

Recalling Memory:
1. If the power is on, turn off the power first.
2. Press and hold the Power button for about 3 seconds until the last recorded
Temperature is displayed.
3. Pressing the Power button repeatedly will take you to each recorded temperature
in the memory.
4. After you release the Power button the unit will return to all segments display.
5. Wait for the hourglass icon to disappear, then two beeps will be heard to indicate that
the thermometer is now "ready to measure".
(2)
(4)
(5)
Two "Beeps"
Deleting Memories:
1.Repeat the first two steps of "Recalling Memories".
2.Press and hold the Power button for three seconds until "dEL" is displayed.
3. (a) To delete:
Press and release the Power button to erase all of the records in the unit. A beep
is heard.
(b) To cancel:
DO NOT press the Power button for 10 seconds, the unit will return to all
segments display.Wait for the hourglass icon to disappear, then two beeps will be
heard to indicate that the thermometer is now "ready to measure".
(2) (3b)
5
Indication 1: The thermometer is too cold or too hot
to operate.
Verify room temperature is within product
Instruction:
range 60.8°F to 104.0°F (16°C to 40°C).
Retake temperature using proper technique (see section 3).
Indication 2: Temperature did not register because of
poor contact, patient movement or poor
placement.
Turn the unit OFF, wait two minutes,
Instruction:
turn it ON again and retake temperature
using proper technique (see section 3).
Indication 3: Unit malfunctioned.
Instruction: Do not use the thermometer – contact
distributor for instructions (see section 7).
Low Batteries Indication: Battery icon is on continuously.
Instruction: The batteries have enough remaining life
for approximately 30 more measurements.
Drained Batteries Indication: Displays OFF with battery
icon flashing when thermometer is turned
on and the device automatically turns itself
OFF after 15 seconds.
Instruction: The batteries are drained - replace batteries
(see section 2).
7
(3)
Two "Beeps"
IMPORTANT:
" Clean the thermometer after each use (see section 4).
" In order to ensure accurate measurement,please wait at least two minutes
between consecutive measurements for the unit to readjust to room
temperature.
" If the thermometer is not turned off, it will shut off automatically within 1 minute.
" Once the thermometer is "ready to measure", it will shut off automatically after 1
minute if it has not made good contact or maintained good contact with the patient's skin.
" Because the thermometer is a very sensitive device, the patient and thermometer should
be in the same room temperature (approx. 60.8~104.0? ) for at least 20 minutes before
using to avoid any incorrect measurements.
4. Care and Cleaning:
* Wipe the tip and probe with an alcohol swab or cotton swab moistened with
70% isopropyl alcohol before & after each use. * After cleaning, wait at least 2
minutes before taking a measurement for the unit to readjust to room temperature.
* Use only a soft dry cloth to clean the body of the thermometer (if necessary).
* Never use an abrasive cleanser or submerge the thermometer in
water or other liquids.
* Do not expose the thermometer to extreme temperatures, humidity, direct
sunlight or shock. Store at room temperature.

5. Troubleshooting and Special Indications:

The thermometer has been designed to display feedback/warnings to ensure proper usage
and accurate temperature measurement. When an error or indication appears, one "beep"
signal will be heard once every second for 5 seconds and then the thermometer will turn
off automatically. In the event of a malfunction or incorrect temperature measurement,
the following warnings will be displayed:
Indication: The measured temperature is below 95°F
(35°C) Display will read LO.
Instruction: Turn the unit OFF to wait at least 2 minutes
and then ON again. Retake temperature using
proper technique (see section 3).
Indication: The measured temperature is above 107.6°F
(42°C). Display will read HI.
Instruction: Turn the unit OFF to wait at least 2 minutes
and then ON again. To verify the reading,
retake temperature using proper technique
(see section 3).
* * WARNING - A high fever condition requires seeking immediate
medical attention * *
HIGH FEVERS ARE DANGEROUS
6

6. Technical Specifications:

Feature Performance / Data
Measurement time 6 –10 seconds
Measurement locations Temporal artery area of the forehead
Measurement range 95.5°F to 107.6°F (35°C to 42°C)
Operation environment 60.8°F to 104.0°F (16°C to 40°C)
Humidity: 15-95% (non condensing)
Storage environment -4°F to 122°F (-20° C to 50° C),
Humidity: 15-95% (non condensing)
Measurement readout Fahrenheit or Celsius
Accuracy Complies with ASTM E 1112-00 standard requirements
Display TN LCD 1" x 1" (27.0mm x 27.0mm)
Batteries 2 AAA 1.5volt batteries
Battery life Minimum 1000 full duty cycles over 24 month period
Weight 2.24oz (56.2gr) including batteries
Dimensions 3.86" x 1.79" x 1.17" (9.9 cm x 4.6 cm x 3.0 cm)
Memory Nine sets
Auto shut off After 60 seconds
Case material Food grade ABS plastic
Probe material Stainless steel and food grade ABS plastic
Warranty 1 year
7. Warranty and Service Information:
This thermometer has a One Year Limited Warranty against manufacturers defect under
normal use. Following the directions closely will ensure years of dependable operation.
If the thermometer does not function properly, first check the batteries (see Battery
Replacement instructions – section 2). Replace if necessary.
If the thermometer does not function properly, please write BESTMED, LLC at 331
Corporate Circle, Ste E, Golden, CO 80401 or you may call customer service at 1-877-
299-6700. Our representative will provide further instruction on how to correct the
trouble or will ask you to return it for repair or replacement.
* Internally powered device * Type - BF Applied part.
* Degree of protection against ingress of water: Ordinary
Read the Instructions For use
Distributed by: BESTMED, LLC" Golden, CO 80401
Manufactured by: K-jump Health Co., Ltd.
Made in China
Applied part type BF equipment
8