Kenmore 69317 Owner's Manual page 10

OPERATING INSTRUCTIONS (CONT.)
ELECTRONIC AUTO-OFF
The Kenmore ELECTRONIC Iron is
equipped with an electronic auto-off
feature. The electronic auto-off switches
the iron off if it has been left standing
unmoved in any position (sideways, flat or
upright) for approximately 7-9 minutes. A
red light on the LED display panel will
flash when the iron switches itself off.
(Fig. 7) To switch the iron back on, just
shake the iron side-to-side several times.
Flash
Fig. 7
EMPTYING THE IRON
1. Always empty iron after each use.
2. When finished using the iron, turn
the variable steam control dial to
"0" and press the electronic
temperature control button until the
power light is lit.
3. Unplug the iron from the electrical
outlet.
4. Turn the iron upside down over the
sink with the tip pointing downward
and allow the water to flow from the
opening.
5. Place iron upright and allow to cool
before storing.
CAUTION!
Use caution when
emptying the iron. Burns may occur
from touching hot metal surfaces,
hot water or steam.
SELF CLEANING
It is important to "Self Clean" the iron at
least every two weeks to remove scale,
calcium, etc. The harder the water, the
more often the iron should be self
cleaned.
1. Set the variable steam control dial
to any steam position.
2. Fill the water tank up to the "MAX"
level.
3. Stand the iron on its heel. Plug the
iron into the electrical outlet.
4. Press the electronic temperature
control button until you get the
"MAX" temperature setting on the
display panel and wait until the iron
heats up and temperature setting
light stops flashing.
5. Turn the variable steam control dial
all the way to right to the self-cleaning
position and hold the iron horizontally
over the sink. (Fig. 8).
6. Boiling water and steam will now be
ejected from the holes in the
soleplate. The impurities and scale
are washed away with it.
7. Move the iron back and forth as this
happens.
8. If there is any water left in the water
tank after the iron stops steaming,
just empty the remaining water in a
sink following the instructions for
emptying the iron.
9. Turn the variable steam control dial to
the "0" position when the water tank
is empty.
10. Place the iron back upright on its
heel to cool down before storing.
Fig. 8
8
DISPOSITIVOS DE LA PLANCHA ELECTRÓNICA KENMORE
3
1 2
4
BOTÓN DE CHORRO CORTO O
1.
LARGO DE VAPOR
Gire este botón completamente a la
izquierda para chorros cortos de vapor
que ayudan a eliminar las arrugas
rebeldes de las telas como el denim o
mezclilla, telas de algodón o de lino
Para chorros largos de vapor, gire este
botón completamente a la derecha.
Así la plancha puede usarse para
planchar vertical u horizontalmente.
BOTÓN ATOMIZADOR DE AGUA
2.
Presionando éste botón, se aplica un
horro definido de agua que moja la tela
levemente.
REGULADOR DE VAPOR
3.
Regula el vapor entre mínimo y máximo
para diferentes tipos de materiales.
Este dispositivo lava automáticamente
la suela de la plancha por dentro con
agua.
BOTÓN DE CONTROL
4.
ELECTRÓNICO DE
TEMPERATURA
Presione este botón para graduar la
temperatura de la plancha según el tipo
de tela.
Función Anti Goteo
5.
Corta el agua cuando la temperatura de
la plancha está demasiado baja.
Panel de diodos indicadores
PANEL DE DIODOS
6.
INDICADORES
Indica la selección de tela en la
izquierda y de temperatura en la
derecha.
TOMA DE AGUA
7.
La tapa evita que el polvo y cuerpos
extraños entren al tanque de agua
de la plancha y que el agua se
derrame al planchar.
FILTRO DE CALCIO
8.
INCORPORADO
Evita la acumulación de calcio y
prolonga la vida de la plancha.
SUELA DE ACERO
9.
INOXIDABLE
Provee el máximo de
desplazamiento y retención de
calor.
CORDÓN PIVOTANTE
10.
Para uso con mano derecha o
izquierda. Pivotea de arriba a
abajo, evitando arrastrarse sobre la
tela. El protector flexible del cordón,
evita que se deshilache.
16