Table of Contents
Advertisement
Operating and maintenance instructions for
Everdure Lumina Series II
Australian made by:
Everdure
A Division of Shriro Australia Pty Limited
101 Sheffield Road, Welshpool, Western Australia, 6106
SHRIRO AUSTRALIA PTY. LIMITED
23-27 CHAPLIN DRIVE, LANE COVE, NSW 2066
Telephone: 1300 766 066
FOR PEACE OF MIND AND THE HIGHEST LEVEL OF AFTER SALES
SERVICE, REGISTER YOUR PRODUCT ON:
www.everdure.com
-
(Refer to the Everdure Product Warranty Registration Form on this
manual)
IMPORTANT
PLEASE READ THESE INSTRUCTIONS CAREFULLY
BEFORE USING YOUR NEW EVERDURE HEATER
1
EVB 0480
Advertisement
Table of Contents
Related Manuals for Everdure Lumina II Series
Summary of Contents for Everdure Lumina II Series
- Page 1 Telephone: 1300 766 066 FOR PEACE OF MIND AND THE HIGHEST LEVEL OF AFTER SALES SERVICE, REGISTER YOUR PRODUCT ON: www.everdure.com (Refer to the Everdure Product Warranty Registration Form on this manual) IMPORTANT PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USING YOUR NEW EVERDURE HEATER...
- Page 2 EVERDURE MODEL LUMINA SERIES II The Everdure Convection gas space heaters are described as thermostatically controlled, portable, flueless convection heaters for use with Natural gas. The heater is supplied with an approved flexible hose. A label is attached to the rear of the heater stating the type of gas for which it has been manufactured and adjusted.
- Page 3 DATA LABEL The Data Label, as shown below, is located on the rear panel of the heater. EVERDURE CONVECTION HEATER MODEL LUMINA SERIES II Gas Type N.G. Nom Gc Mj/Hr Burner Pressure Hi 0.82 Main Burner Injector 2.30 Turn down Injector A.G.A.
- Page 4 The heater can be switched off automatically using the Sleep Timer. POWER FAILURE Your Everdure heater will not operate in the event of a power failure. Should the power fail while the heater is operating, the heater will stop running. When the power is re-established, it will be necessary to press the reset button before operating the heater.
- Page 5 Important Warnings Do not spray aerosols in the vicinity of the heater while operating. Keep combustible materials away from heater. See page 2 for details. Do not sit on or lean against the heater. Do not place any obstructions in front of the heater. See page 2 for details. Do not allow children to place items into the louvre section of the heater.
- Page 6 CONTROL PANEL FUNCTIONS LCD DISPLAY: Displays the current settings P1 BUTTON: P2 BUTTON: Press this button to Press this button to set a second set a program time program time MINUTES BUTTON: HOURS BUTTON: Press this button to set Press this button to the minutes on the set the hours on the time and for...
- Page 7 Press the ‘OFF’ button on the heater control panel. Your new Everdure Lumina heater is know functional with your remote control. The remote control is also supplied with a remote control holder. The holder can be attached to the unit or any other area of the room by placing the double sided tape supplied onto the holder and then to the position desired.
- Page 8 TURNING HEATER ON AND OFF 4) Starting the heater. After the time and desired temperatures have been set, the heater can be started by pushing the ‘ON’ button. When this is done, the orange LED will light up next to the green LED, to indicate that the heater is now working in the high mode.
- Page 9 9) Setting program times. The heater can be programmed to switch ON and OFF automatically, twice per day. This function is particularly useful when you want the heater to turn ON before you wake up and turn OFF as you leave for work.
- Page 10 11) Sleep Timer The sleep timer is used to automatically turn OFF the heater after a pre-determined amount of time. This function will only operate whilst the heater is running. Please note: this function does not operate with the fan mode. To set the sleep timer, press the ‘Sleep’...
- Page 11 3) Flame Failure This message is displayed when the heater has failed to ignite. Press the ‘Reset’ button, and then press the ‘On’ button to restart the heater. If the heater fails to ignite and the same message appears, see the fault finding FLAME section of this booklet.
-
Page 12: Fault Finding
This is quite normal. If there is a fault with the heater which continues and cannot be rectified by consulting the fault finding chart, contact your nearest EVERDURE service centre or contact Everdure on 1300 766 066 from anywhere in Australia. - Page 13 CLEANING The Everdure Lumina Series II convection heater only requires a small amount of cleaning to keep the heater operating at safe and efficient levels. IMPORTANT DISCONNECT GAS AND ELECTRICAL SUPPLIES BEFORE CLEANING ANY SURFACES The outer surface of the heater should only be cleaned or dusted with a damp cloth. Never use harsh or abrasive cleaners or cloths when cleaning the heater.
- Page 14 4. Damage or expense incurred as a result of incorrect or unauthorised installation, accident, interference by unauthorised persons or misuse, is NOT covered by this warranty. 5. Any claim under this warranty must be made direct to Shriro Australia Pty Limited - Everdure Division, or their authorised service centre.
- Page 15 Everdure Product Warranty Registration Thank you for choosing an Everdure product. We are confident that it will give you excellent service and satisfaction. Registering your purchased product will allow us to contact you in the unlikely event of a service issue or if you are making a claim under the terms of our warranty.
- Page 16 Privacy policy: Everdure is committed to protecting your personal privacy. Your personal information that you have provided in this form (e.g. name, street address, e-mail address and telephone/mobile number) is used solely by Everdure for the express purpose for which it was collected (e.g. to respond to your enquiry regarding your product).
Need help?
Do you have a question about the Lumina II Series and is the answer not in the manual?
Questions and answers