Page 2: Introduction
Introduction Ford’s Commitment to You At Ford Motor Company, excellence is the continuous commitment to achieve the best result possible. It is dedication to learning what you want, determination to develop the right concept, and execution of that concept with care, precision, and attention to detail.
Page 3 This guide describes equipment and gives specifications for equipment that was in effect when this guide was approved for printing. Ford may discontinue models or change specifications or design without any notice and without incurring obligation.
Page 4 Canadian Owners — French Version French Owner Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3.
Page 5 You can get more protection for your new car or light truck by purchasing a Ford Extended Service Plan (Ford ESP). Ford ESP is the only extended service program with the Ford name on it and the only service contract backed by...
Page 6 Ford ESP is an optional service contract, backed and administered by Ford. It provides: protection against repair costs after your Bumper to Bumper Warranty expires; other benefits during the warranty period (such as: reimbursement for rentals; coverage for certain maintenance and wear items).
Page 7 The break-in period for new brake linings lasts for 100 miles (160 km) of city driving or 1,000 miles (1,600 km) of highway driving. Use only the type of engine oil that Ford recommends. See Engine oil recommendations in the Index. Do not use special “break-in”...
Page 9: Table Of Contents
Table of Contents Introduction ............ 1 Instrumentation ..........7 Audio .............. 25 Controls and Features ........ 55 Seating and Safety Restraints ....103 Starting ............149 Driving ............157 Roadside Emergencies ......181 Maintenance and Care ......209 Capacities and Specifications ....265 Reporting Safety Defects (U.S.
Page 11 The instrument panel (dashboard) on your vehicle is divided into several different sections. The illustrations on the following pages show the major parts of the instrument panel that are described in this chapter. Some items shown may not be on all vehicles. In your vehicle, the warning lights and gauges are grouped together on the instrument panel.
Page 14 The Cluster The following warning lights and gauges are on the cluster. All of the warning lights and gauges alert you to possible problems with your vehicle. Some of the lights listed are optional. The following sections detail what each of these indicators means.
Page 15 Anti-Lock Brake System Light (If equipped) This warning light will go on each time you start your vehicle. If it remains on for longer than five seconds, you should shut off your engine and restart. If the anti-lock brake light stays on, this indicates that the anti-lock feature is disabled and should receive immediate attention by a qualified service technician.
Page 16 WARNING If the anti-lock brake system warning light remains on or comes on while driving, have the braking system checked by a qualified service technician as soon as possible. NOTE: If a fault occurs in the anti-lock system, and the brake warning light is not lit, the anti-lock system is disabled but normal brake function remains operational.
Page 17 If the light fails to illuminate, continues to flash, remains on, or you hear a beeping sound, have the system serviced at your Ford or Lincoln-Mercury dealer immediately. The air bag readiness light Low Coolant Warning Light (If equipped)
Page 18 The low coolant warning light Charging System Light This light indicates that your battery is not being charged and that you need to have the electrical system checked. The charging system light This light illuminates every time you turn the ignition to the ON or START position (engine off).
Page 19 This light tells you that the Transmission Control Switch (TCS) has been pushed. When the light is on, the transmission will not shift into overdrive. Depressing the control will return the vehicle to “overdrive on” mode. The transmission will be in the “overdrive on”...
Page 20 Check Engine Warning Light This light illuminates when the engine’s Emission Control System requires service. It will also illuminate when the ignition key is in the ON position and the engine is off. The check engine warning light Anti-Theft Alarm Light Anti-theft alarm light This light is used when you set the anti-theft alarm system.
Page 21 Fuel Gauge The fuel gauge The fuel gauge displays approximately how much fuel is in the fuel tank only when the ignition switch is ON. For proper fuel gauge indication after adding fuel, turn the ignition switch OFF while refueling the vehicle. The fuel gauge indicator may vary slightly when the vehicle is in motion.
Page 22 conditions, and under certain driving conditions such as, heavy stop and go traffic, or driving up hills in hot weather, for the pointer to indicate at the top of the NORMAL band. If, under any circumstances, the pointer moves above the NORMAL band, the engine is overheating and continued operation may cause engine damage.
Page 23 Speedometer The speedometer (GT similar) The speedometer tells you how many miles (kilometers) per hour your vehicle is moving. Odometer The odometer tells you the total number of miles (kilometers) your vehicle has been driven. Trip Odometer If you want to track your mileage up to 999.9 miles (kilometers), use the trip odometer.
Page 24 Tachometer The tachometer (GT similar) The tachometer displays the approximate engine revolutions per minute (rpm), or how fast the engine is running. The white zone shows the highest number of engine revolutions per minute (rpm) at which you should drive your car. Driving with the pointer in the red zone may cause engine damage.
Page 25 Battery voltage gauge Engine Oil Pressure Gauge This gauge indicates the engine oil pressure, not the oil level. However, if your engine’s oil level is low, it could affect the oil pressure. With the engine running, the pointer should move into the NORMAL band.
Page 26 If you lose engine oil pressure: 1. Pull off the road as soon as safely possible. 2. Shut off the engine immediately or severe engine damage could result. 3. Check the engine’s oil level, following the instructions on checking and adding engine oil, see the Engine Oil in the Index.
Page 28 Electronic Stereo Cassette Radio Using the Controls on Your New Radio How to turn the radio on and adjust the volume Press the “POWER” button to turn the radio on. Press it again to turn it off. Press the right (+) side of the “VOLUME” button to increase the volume.
Page 29 Using the “AMS” function to manually tune your radio You can change the frequency up or down one increment at a time by first pressing the “AMS” button, (display shows “TUNE”) then pressing and releasing either the right a or left b side of the “SEEK”...
Page 30 Setting the Station Memory Preset buttons Your radio is equipped with 6 station memory buttons. These buttons can be used to select up to 6 preset AM stations and 12 FM stations (6 in FM1 and 6 in FM2). Follow the easy steps below to set these buttons to the desired frequencies: 1.
Page 31 Speaker features and operation Adjusting speaker balance Balance control allows you to adjust the sound distribution between the right and left speakers. Push the “AUDIO” button repeatedly until the display reads “BAL.” Push the right (+) side of the “VOLUME” button to shift the sound to the right speakers, and push the left ( ) side to shift the sound to the left speakers.
Page 32 How to locate a desired track on the tape NOTE: The tape track or side number indicated in the display does not necessarily correspond to the tape track or side number on the cassette label. It is used only to indicate when the tape mechanism reverses tracks.
Page 33 In order to keep your cassette tape player performing the way it was meant to, read and follow these simple precautions: Using a Ford Cassette Cleaning Cartridge or equivalent to clean the tape player head after 10-12 hours of play will help maintain the best playback sound and proper tape operation.
Page 34 If a tape is loose inside the cassette, tighten it before playing by putting your finger or a pencil into one of the holes and turning the hub until the tape is tight. Loose labels on cassette tapes can become lodged in the mechanism.
Page 36 Ford Compact Disc Player The Ford Compact Disc Player operates when the Audio System is on and a disc is inserted (label side up). Handle the disc by its edge only. (Be sure to read and follow all of the care...
Page 37 NOTE: Once a disc is inserted, the disc opening is secured to prevent the accidental insertion of a second disc. NOTE: The CD player has heat protection circuitry to protect the laser diode. If the temperature of the player reaches 167˚F (75˚C), the heat detection circuit will shut off the player and “HOT”...
Page 38 How to fast forward or reverse your CD player To quickly search for a particular point in a selection, press the right e side of the “REV/FF” button (to fast forward) or the left f side (to rewind). While either side of the button is pressed, the disc goes forward or backward at two different speeds depending on how long the button is held down.
Page 39 Special Features of Your CD Player Compression The compression feature will bring soft and loud passages closer together for a more consistent listening level. To turn the compression on, press the “COMPRESS” button. When on, the compression indicator (“COMP”) will appear in the display.
Page 40 How To Take Care of and Clean Your CD Player and Discs To ensure the continued performance of your Ford Compact Disc Player, carefully read the following precautions: Always handle the disc by its edge. Never touch the playing surface.
Page 41 CD format. Because of this, a new disc that is free of dust and scratches could be defective and may not play on your Ford Compact Disc Player.
Page 42 If play does not begin after the CD button is pushed: The radio is not on. The unit is in the stop mode. Moisture may have condensed on the lenses within the unit. If this occurs, remove the disc and wait approximately an hour until the moisture evaporates.
Page 44 Mach 460 Sound System Using the Controls on Your New Radio How to turn the radio on and off Press the “POWER” button to turn the radio on. Press it again to turn it off. How to adjust the volume Press the side of the “VOLUME”...
Page 45 Using the “TUNE” function You can change the frequency up or down one increment at a time (FM changes in increments of 200 kHz; AM changes in increments of 10 kHz) by first pressing the “SCAN/TUNE” button twice (display shows “TUNE”), then —...
Page 46 Using the “SCAN” function Pressing the “SCAN/TUNE” button once enters the scan mode (display will indicate “SCN”). Pushing the right a side of the “SEEK” button will begin the scan mode up the frequency band, stopping on each listenable station for approximately a five-second sampling.
Page 47 Using the Automatic Memory Load feature If no stations are in memory preset, you can activate the Auto Memory Load feature by pressing and holding the “AUTO PRESET” button for approximately three seconds. Auto Memory Load sets all memory buttons in AM, FM1 and FM2 sequentially by seeking out the first six strong stations for the respective band and storing them in memory...
Page 48 To deactivate the Auto Memory Store mode and return to the manually-set memory button stations (or those stations set using Auto Memory Load), simply push the “AUTO PRESET” button. Display will show “AUTO” then “OFF.” The next time Auto Memory Store is activated on that band, the radio will store the next set of five strong stations.
Page 49 Adjusting speaker fader Fade control allows you to adjust the sound distribution between the front and rear speakers. Push the “AUDIO” button repeatedly until the display reads “FADE.” Push the right (+) side of the “VOLUME” button to shift the sound to the front speakers, and push the left ( ) side to shift the sound to the rear speakers.
Page 50 How to locate a desired track on the tape There are four ways to quickly locate a desired selection on the tape. You can use the fast forward, rewind, “SEEK” or “SCAN” function. Following are brief descriptions of each. Fast forwarding the tape To fast forward the tape, press the “FF”...
Page 51 Using the “SCAN” function with your cassette tape player Press the “SCAN/TUNE” button to enter the scan mode (display indicates “SCN”). Pushing the right a side of the “SEEK” button will begin the forward scan mode on the tape currently playing, stopping on each tape selection for approximately an eight-second sampling.
Page 52 How to store the tape Press the “AM/FM” button to stop the tape player and resume radio play. The cassette will be stored in the tape player and the X symbol in the display will be lit until you push the “PLAY PROG”...
Page 53 In order to keep your cassette tape player performing the way it was meant to, read and follow these simple precautions: Using a Ford Cassette Cleaning Cartridge or equivalent to clean the tape player head after 10-12 hours of play will help maintain the best playback sound and proper tape operation.
Page 54 Common Radio Reception Conditions Several conditions prevent FM reception from being completely clear and noise-free, such as the following: 1. Distance/Strength The strength of the FM signal is directly related to the distance the signal must travel. The listenable range of an average FM signal is approximately 25 miles (40 kilometers).
Page 55 To minimize these conditions, a stereo/mono blend circuit has been incorporated into this system. This feature automatically switches a weak stereo signal to a clearer monaural signal, which improves the quality of reception. Several sources of static are normal conditions on AM frequencies.
Page 56 Ask your dealer for a copy of this limited warranty. Service At Ford, we stand behind our audio systems with a comprehensive service and repair program. If anything should go wrong with your Ford audio system, return to your dealer for service.
Page 57: Controls And Features
Controls and Features The main controls for the climate control system, clock, and radio are on the instrument panel. NOTE: Any cleaner or polish that increases the gloss (shine) of the upper part of the instrument panel should be avoided. The dull finish in this area is to help protect the driver from undesirable windshield reflection.
Page 58 The controls for the optional heating and air conditioning system The heating system in the optional heating and air conditioning system operates the same as the heater only system. See The Heater Only System. To cool your vehicle quickly in warm weather, turn the SELECT control to MAX A/C, turn the TEMP control all the way to the end of the blue range (full left) and turn the FAN control to HI.
Page 59 Under normal conditions, the SELECT control should be left in any position other than MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct. The Heater Only System (If equipped) You can heat the inside of your vehicle, defrost the windshield, or use the vents by adjusting the three controls in the center of the instrument...
Page 60: Rear Window Defroster
To heat the inside of your vehicle and defrost the windshield and side windows at the same time, turn the SELECT control to MIX, turn the TEMP control into the red range, as required, and turn the FAN control to the desired speed between LO and HI.
Page 61: The Interior And Exterior Lights
Clear away any snow that is on the rear window before using the defroster. With the engine running, push the defrost button. After approximately 10 minutes, the defroster will turn off. If the window is still not clear, turn the defroster on again. The defroster will turn off when the ignition key is turned to the OFF position.
Page 62 R WARNING The Daytime Running Light (DRL) system will not illuminate the tail lamps and parking lamps. Turn on your headlamps at dusk. Failure to do so may result in a collision. Turning On the Exterior Lights To turn on the headlamps, parking lamps, license plate lamps, side markers, and tail lamps, use the control knob that is to the left of the steering wheel.
Page 63 To turn on the parking lamps, license plate lamps, tail lamps and marker lamps, move the knob to the first position. To turn on the headlamps, parking lamps, license plate lamps, tail lamps and marker lamps, move the knob to the second position. For more information about how the high beams work, see the high beam section later in this chapter.
Page 64 Clock The digital clock 1. To set the hour, press and hold the H button. When the desired hour appears, release the button. 2. To set the minutes, press and hold the M button. When the desired minute appears, release the button.
Page 65 Power Point Electrical Outlet The power point outlet is located on the console to the right of the shift lever. This outlet should be used in place of the cigarette lighter for optional electrical accessories. NOTE: Do not plug optional electrical accessories into the cigarette lighter.
Page 66 Your vehicle may have several small storage compartments: a glove compartment that locks (if equipped). coin holders located behind the ashtray. These are deleted if fog lamps or convertible top are ordered. Using the Remote Control for the Trunk (If equipped) You can use the remote control inside your glove compartment to unlock and open the trunk.
Page 67 Ignition Understanding the Positions of the Ignition The positions of the key in the ignition ACC allows some of your vehicle’s electrical accessories such as the radio and the windshield wipers to operate while the engine is not running. You must push the key release button to turn to the ACC position if your vehicle has a manual transmission.
Page 68 Removing the Key From the Ignition 1. Put the gearshift in P (Park) (automatic transmission) or 1 (First) (manual transmission). 2. Set the parking brake fully. 3. Turn the ignition to the OFF (manual transmission) or LOCK (automatic transmission). 4. Push in the key release button until it catches and stays in (manual transmission only).
Page 69 R WARNING Always set the parking brake fully and make sure that the gearshift is latched in P (Park) (automatic transmission) or 1 (First) (manual transmission). R WARNING Do not leave children, unreliable adults, or pets unattended in your vehicle. The Turn Signal Lever You can use the turn signal lever on the left side of the steering column to:...
Page 70 Turn Signals Move the lever up to signal a right turn. Move it down to signal a left turn. The corresponding indicator light in the instrument cluster will flash. If the turn signal stays on after you turn, move the lever back to the center (off) position. For lane changes, move the lever far enough to signal but not to latch.
Page 71: Windshield Wipers And Washer
Windshield Wipers and Washer To turn on the windshield wipers, the ignition key must be turned to the ON or ACC position. Rotate the end of the lever away from you to activate the wipers. The first seven detents are interval wipe positions, the eighth detent is the LO position and the ninth detent is the HI position.
Page 72 If the washer does not work, check the washer fluid level and fill it if it is low. See the Maintenance and Care chapter. If there is enough fluid, consult your nearest Ford or Lincoln-Mercury dealer. Do not try to clean the windshield when the...
Page 73 Hazard Flasher The hazard flasher serves as a warning to other drivers to be careful when approaching or passing your vehicle. The control for the hazard flashers...
Page 74: Tilt Steering
Horn To sound the horn, push the center pad area of the steering wheel. The horn on the steering wheel Tilt Steering R WARNING Never adjust the steering wheel when the vehicle is moving.
Page 75 The lever to tilt the steering wheel To change the position of the steering wheel, pull the release lever on the column toward you. Tip the steering wheel to the desired position. Release the lever to lock the steering wheel in place.
Page 76 Speed Control (If equipped) The speed control switches on the steering wheel To Turn Speed Control Off Press OFF, OR Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. To Turn Speed Control On Press ON To Set a Speed Press SET ACCEL.
Page 77 Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill. If your vehicle speed is faster than the set speed while driving on a downhill in j (Overdrive), you may want to shift to the next lower gear to reduce your vehicle’s speed.
Page 78 To Set a Lower Set Speed Press and hold COAST. Release the switch when the desired vehicle speed is reached. Press and release COAST. Each press will decrease the set speed by 1 mph (1.6 km/h). Depress the brake pedal. When the desired vehicle speed is reached, press SET ACCEL.
Page 79 Map and Reading Lamps Your vehicle has two map lamps for the passenger and the driver. To turn on the map lamps, push the switch next to each lamp. Front seat map and dome lamps (coupe only) The dual beam map lamps are located on each side of the dome lamp.
Page 80 R WARNING Make sure you can see clearly through the rearview mirror at all times. Do not block your vision. If you cannot see through the mirror, it could result in a collision, injuring yourself and others. Rearview Mirror and Lamp Assembly (convertible only) This rearview mirror contains two lamps which function as courtesy lamps when the doors are...
Page 81: Sun Visors
Sun Visors Turning on the Mirror Light on the Sun Visors (If equipped) To turn on the visor mirror light, lift the mirror cover. The mirror on the sun visor Doors Power Door Locks (If equipped) If your vehicle has power door locks, the controls to lock the doors are on the trim panel of the front door.
Page 82 The power locks on the driver’s door Windows Using the Power Windows (If equipped) Each door has a power control that opens and closes the window on that door. The driver’s door has a master control panel that operates the windows.
Page 83 The master controls on the driver’s door — convertible shown To lock out all window switches except the master controls, press the window lock switch once. To restore control to the individual windows, press the switch again. There is also an Express Down feature on the driver’s power window.
Page 84 Adjusting the Side View Mirrors The switch for controlling the dual electric remote control mirrors is located on the driver’s door. Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products. The mirror controls on the driver’s door To adjust the side mirrors: 1.
Page 85 The Right Side Convex Mirror The side view mirror on the right is a convex mirror. This mirror gives you a wider view of the lanes on your right and behind you. R WARNING The right side view mirror makes objects appear smaller and farther away than they actually are.
Page 86 Fog Lamps (If equipped) The fog lamps switch is located on the console to the left of the parking brake. The fog lamps act as a supplement to the low beam headlamps under limited visibility conditions such as rain, snow, dust or fog and operate only when the low beam headlamps are on.
Page 87 Convertible (If equipped) NOTE: Do not store articles behind rear seat. Articles stored in the convertible top stowage compartment may break the rear glass window when the top is lowered. Lowering the Convertible Top The convertible top can be lowered with the side windows either up or down.
Page 88 5. If the top has not been lowered for some time and sticks to the windshield header, push the front of the top up slightly with your hand to loosen it. Convertible top header clamps 6. Push the convertible top switch on the console in front of the armrest and hold until the top is completely stored.
Page 89 Installation of the Boot To install the boot: 1. Insert boot tongue into groove located on rear seat.
Page 90 2. Push boot forward until rear attachment engages under molding. 3. Push forward flap of boot until both clips engage under trim panel edge. Repeat on other side of vehicle.
Page 91 4. Tuck side attachments under molding. Repeat on other side of vehicle. 5. Push and pull front of boot to ensure tongue is engaged into groove.
Page 92 6. Removal Raising the Convertible Top NOTE: CONVERTIBLE TOP WILL NOT OPERATE UNLESS PARKING BRAKE IS ENGAGED. Do not raise the top while the vehicle is moving because the top may be severely damaged. To raise the convertible top: 1. Bring the vehicle to a complete stop. Engage the parking brake.
Page 93 Convertible Top and Padded Molding Care To avoid damage to the vinyl top and moldings, use only an approved Ford cleaner, or equivalent. Do not use stiff bristle brushes or abrasive material or cleaners. Hot waxes applied by automatic car washes can affect the cleanability of vinyl material.
Page 94 The positive location floor mat hook Anti-Theft Alarm System When armed, this system helps protect your vehicle against break-ins or theft. When an unauthorized entry occurs, the system triggers and will: flash the parking lamps, and alarm indicator lamp honk the horn disable the starting circuit to prevent the vehicle from being started...
Page 95 NOTE: The factory installed Remote Entry System has a PANIC feature that also honks the vehicle horn and flashes the interior/exterior lamps when the PANIC button on the remote entry transmitter is pushed. The PANIC alarm and the Anti-Theft alarm are two separate features.
Page 96 4. Close all doors. The alarm indicator light will then remain on steadily for approximately 30 seconds and then go out. When the light goes out, the system is armed. NOTE: Be sure to close all doors completely. If not, the alarm indicator light will remain on.
Page 97 Triggering the Alarm System The armed system will be triggered if: any door is opened without disarming the system first (see previous paragraphs) the trunk lock cylinder is removed NOTE: You can open the trunk with your key without setting off the alarm. Disarming a Triggered System The alarm can be disarmed by: unlocking a front door with the key...
Page 98 Be sure to purchase only coded keys with a Ford or Mercury logo on it to ensure proper functionality. If both supplied keys are lost or stolen, the vehicle must be brought to the dealership for re-initialization.
Page 99: Remote Entry System
If the key has been coded, the theft indicator will illuminate for two seconds. The key can then be used to start the vehicle. Repeat until all chosen keys have been coded (max=16). If the key coding failed, the theft indicator will flash and the vehicle cannot be started.
Page 100 Remote Unlocking the doors and opening the trunk To unlock the driver’s door, press the UNLOCK control. To unlock the other doors, press the UNLOCK control a second time within five seconds of unlocking the driver’s door. To open the trunk, press the TRUNK control. Locking the doors To lock all the doors, press the LOCK control.
Page 101 When you use the remote entry UNLOCK, TRUNK or PANIC controls, the illuminated entry system turns on the interior lights for 25 seconds. You can turn these lights off with the LOCK control or by turning the ignition to the RUN position.
Page 102 Replacement batteries can be purchased at most pharmacies, watch stores or at your Ford or Lincoln-Mercury dealer. NOTE: The operating range of the remote entry system can also be affected by...
Page 103 Replacing the batteries The remote can be snapped apart to replace the batteries by twisting a thin coin between the two halves of the remote. DO NOT TAKE THE FRONT PART OF THE REMOTE APART. When installing the new batteries, be sure to place the positive (+) side down as marked.
Page 104: Seating And Safety Restraints
Seating and Safety Restraints Seats Head Restraints If you use them properly, head restraints will help protect your head and neck in a collision. A head restraint helps protect you best if you position it behind your head and not behind your neck.
Page 105 Adjusting Manual Seats In the front seats, you can move the whole seat forward or backward or tilt the back of the seat forward or backward. To move the seats forward or backward: 1. Find the adjustment lever at the lower left corner of the front seat.
Page 106 The front seat adjustment lever To recline the front manual seats: 1. On the side of the seat, find the handle for the recliner. 2. Lift the handle up and hold it in place. 3. Lean against the back of the seat and adjust it to the position you want.
Page 107 Seatback Recline Front seatback release levers It is necessary to use the seatback release when folding the back of the front seat forward for rear seat passenger entry or exit. This release handle is located on the lower outboard back of the seat.
Page 108 Using the Power Seat (If equipped) If your vehicle has a driver side power seat, you can adjust it in several directions. Using the seat adjustment switch, located on the front outboard corner of the driver’s seat, you can raise or lower the whole front seat and move the seat forward or backward.
Page 109 Sport Seat Controls (If equipped) Using the Power Lumbar Supports You can inflate a lumbar support pad in the seat back. To inflate the lumbar pad, push the forward portion of the rocker control. To deflate push the rear portion of the control. GT seat controls...
Page 110 Rear Seat Entry Coupe models Entering the rear seat (coupe) The rotating boot on the lap belt is designed to allow rear seat entry/exit. To enter the rear seat: 1. Remove seat belt from seat belt guide on top of front seat. 2.
Page 111 Convertible models Entering the rear seat (convertible) To enter the rear seat: 1. Remove the shoulder belt from the seat belt guide on top of front seat. 2. Remove the lap belt from the seat belt guide on side of seat. 3.
Page 112 Rear seat release straps To raise the rear seatback: 1. Push the seatback upward until it locks in place. 2. Make sure the seatback is firmly latched by pushing forward and backward on it. WARNING Check to see that the seat and seatback are latched securely in position.
Page 113: Instrumentation
the shoulder belt is snug against the chest the knees are straight forward seat belt is placed in guide on top of seat To help you remember to fasten your safety belt, a warning light may come on and a chime may sound.
Page 114 (if equipped) and child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after any collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision was minor and a...
Page 115: Combination Lap And Shoulder Belts
Combination Lap and Shoulder Belts While your vehicle is in motion, the combination lap and shoulder belt adjusts to your movement. However, if you brake hard, corner hard or if your vehicle receives an impact of 5 mph (8 km/h) or more, the lap and shoulder belt locks and helps reduce your forward movement.
Page 116 Fastening the front seat combination lap and shoulder belt (convertible models) Fastening the rear seat combination lap and shoulder belt coupe and convertible NOTE: Be sure to read and understand Important Safety Belt Information in this chapter. Safety Belts for Front Passenger (Coupe Only) and Rear (Coupe and Convertible) Outboard Seating Positions Your vehicle is equipped with a dual locking...
Page 117 Dual locking mode retractors operate in two ways: Vehicle sensitive (emergency) locking mode In this operating mode, the shoulder belt retractor will allow the occupant freedom of movement, locking tight only on hard braking, hard cornering or impacts of approximately 5 mph (8 km/h) or more.
Page 118 To switch the retractor from the emergency locking mode to the automatic locking mode, perform the following steps: 1. Buckle the lap/shoulder combination belt. 2. Grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and, when allowed to retract, a clicking sound is heard.
Page 119 Automatic locking mode In this operating mode, the lap belt retractor will remain locked and does not allow the occupant freedom of movement. This mode provides the following: A tight lap/shoulder belt on the occupant. Child safety seat installation. This mode must be used when installing a forward facing child safety seat on the front passenger seat.
Page 120 NOTE: When the combination lap/shoulder belt is unbuckled and allowed to retract completely, the retractor will switch to the vehicle sensitive (emergency) locking mode. See the detailed instructions under Safety Seats for Children in this chapter. WARNING The lap belts should fit snugly and as low as possible around the hips, not around the waist.
Page 121 To unfasten all the belts: 1. Push the release button on the end of the buckle. This allows the tongue to unlatch from the buckle. Unfastening the front (coupes) and rear outboard lap/shoulder belts Unfastening the Mustang convertible front outboard lap/shoulder belts...
Page 122 2. While the belt retracts, guide the tongue to its stowed position. If you do not guide the tongue, it may strike you or part of the vehicle. 3. (Coupe only). Place the belt in the belt holder at the top of the seatback. The retracted belt should be stored on this holder when not in use, except when a passenger is entering or leaving the rear seat area of the...
Page 123 4. (Convertible only). Place the shoulder belt in the belt holder at the top of the seatback and place the lap belt in the belt guide at the side of the seat cushion. The retracted belt should be stored on this holder and in the belt guide when not in use, except when a passenger is entering or leaving the rear seat area of the vehicle.
Page 124: Safety Belt Maintenance
(slide bar) (if equipped), child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after any collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision...
Page 125 Failure to follow these instructions may increase the risk of personal injury in the event of a collision. WARNING Do not attempt to service, repair, or modify the air bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer.
Page 126 WARNING If you are close to an inflating air bag, it could seriously injure you. Position your seat such that it is as far back from the steering wheel as possible but still allows you to properly control the vehicle. Children and Air Bags NOTE: For additional important safety information on the proper use of seat...
Page 127 quickly deflate. After the air bag deployment, you may notice a smoke-like, powdery residue or smell the burnt propellant. This is normal. The residue may consist of cornstarch or talcum powder (which is used to lubricate the air bag) or sodium compounds, such as sodium carbonates (e.g.
Page 128 The Air Bag Supplemental Restraint System consists of: driver and passenger air bag modules (which include the inflators and air bags), one or more impact and safing sensors, a system diagnostic module, a readiness light and tone, and the electrical wiring which connects the components.
Page 129: Safety Restraints For Children
If any of these things happen, even intermittently, have the Air Bag Supplemental Restraint System serviced at your Ford or Lincoln-Mercury dealer immediately. Unless serviced, the system may not function properly in the event of a collision. Disposal of Air Bags and Air Bag...
Page 130 When possible, put children in the rear seat of your vehicle. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating positions. WARNING Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle.
Page 131 Safety Seats for Children Use a safety seat that is recommended for the size and weight of the child. Always follow the safety seat manufacturer’s instructions when installing and using the safety seat. When installing a child safety seat, be sure to use the correct safety belt buckle for that seating position, and make sure the tongue is securely fastened in the buckle.
Page 132 Installing Safety Seats in the Front Seat — Convertible Your Mustang Convertible is equipped with a dual locking mode retractor on the lap belt portion of the lap/shoulder belt at the front passenger seat.
Page 133 If you choose to install a child safety seat in the front seat: 1. Position the child seat in the front passenger seat of the vehicle. 2. Pull up on the lap belt, Figure 1.
Page 134 3. Following the child seat manufacturer’s instructions, route the lap/shoulder belt through the child seat or infant carrier and insert the belt tongue into the buckle until you hear and feel the latch engage, Figure 2. Routing the lap/shoulder belt...
Page 135 4. Grasp the lap portion of the belt below the child seat label. Pull upward until all of the belt is extracted and a click is heard. At this time, the lap belt retractor is in the automatic locking mode (child seat restraint mode), Figure 3.
Page 136 5. Allow the belt to retract. A clicking sound will be heard as the belt retracts. This indicates the retractor is in the automatic locking mode, Figure 4. Allowing belt to retract...
Page 137 6. Push down on the child seat while you pull down on the belt to remove any slack in the belt, Figure 5. Removing slack from the belt...
Page 138 7. Before placing the child in the child seat or infant carrier, forcibly tilt the seat from side to side, and also tug it forward to make sure that the seat is securely held in place, Figure 6. Checking that the seat is secure...
Page 139 8. Double check that the retractor is in the automatic locking mode. Try to pull more belt out of the retractor, if you cannot, the belt is in the automatic locking mode, Figure 7. Checking the retractor 9. Check to make sure that the child seat or infant carrier is properly secured prior to each use.
Page 140 Installing Safety Seats in the Front Seat (Coupe only) and Rear Seating Positions (Coupe and Convertible) For seating positions equipped with a dual locking mode retractor, use the following procedure. If you choose to install a forward-facing child safety seat in the front seating positions, move vehicle seat as far back as possible.
Page 141 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. See Figure 2. Be sure that the belt webbing is not twisted. Routing the lap/shoulder belt...
Page 142 4. Insert the belt tongue into the buckle for that seating position until you hear and feel the latch engage. See Figure 3. Make sure tongue is latched securely to buckle by pulling on tongue. Buckling the belt 5. Grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard.
Page 143 Setting the retractor to automatic locking mode 6. Allow the belt to retract. Pull up on the shoulder webbing. A clicking sound will be heard as the belt retracts. This indicates the retractor is in the automatic locking mode. Push down on the child seat while you pull up on the belt to remove any slack in the belt.
Page 144 Allowing shoulder belt to retract Removing slack from belt...
Page 145 7. Before placing the child in the child seat, forcibly tilt the seat from side to side, and tug it forward to make sure that the seat is securely held in place. See Figure 7. Checking that the seat is secure...
Page 146 8. Double check that the retractor is in the automatic locking mode. Try to pull more belt out of the retractor. If you cannot, the belt is in the automatic locking mode. See Figure 8. Checking the retractor 9. Check to make sure that the child seat is properly secured prior to each use.
Page 147 Tether anchor hardware kits (Part Number 613D74), including instructions, may be obtained at no charge from any Ford or Lincoln-Mercury dealer. All vehicles built for sale in Canada include a tether anchor hardware kit. Safety Belts for Children Children who are too large for child safety seats should always wear safety belts.
Page 148 To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards. Belt-positioning booster seats raise the child and...
Page 149: Starting
Starting Fuel-Injected Engines When starting a fuel-injected engine, the most important thing to remember is to avoid pressing down on the accelerator before or during starting. Only use the accelerator when you have problems getting your vehicle started. See Starting Your Engine in this chapter for details about when to use the accelerator while you start your vehicle.
Page 150 3. If you have an automatic transmission, make sure that the gearshift is in P (Park) and the parking brake is set before you turn the key. If you have a manual transmission, make sure that the parking brake is fully set, push the clutch pedal to the floor, and put the gearshift into Neutral before you turn the key.
Page 151 For a cold engine: At temperatures 10˚F (-12˚C) and below: If the engine does not start in fifteen (15) seconds on the first try, turn the key to OFF, wait approximately ten (10) seconds so you do not flood the engine, then try again. At temperatures above 10˚F (-12˚C): If the engine does not start in five (5) seconds on the first try, turn the key to OFF, wait...
Page 152 If the engine does not start after two attempts: 1. Turn the ignition key to the OFF position. 2. Press the accelerator all the way to the floor and hold it. 3. Turn the ignition key to the START position. 4.
Page 153 To turn the heater on, simply plug it into a grounded 110-volt outlet. Ford recommends that you use a 110-volt circuit that is protected by a ground fault circuit interrupter.
Page 154 Guarding Against Exhaust Fumes Carbon monoxide, although colorless and odorless, is present in exhaust fumes. Take precautions to avoid its dangerous effects. R WARNING Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine.
Page 155 If the engine is idling while you are stopped in an open area for long periods of time, open the windows at least one inch (2.5 cm). Also, the heating or air conditioning system should be set to any function except MAX A/C or AUTO. If you use the heater, set the fan speed on MEDIUM or HIGH with the function control knob at any desired position.
Page 156: Driving
Driving Brakes Applying the Brakes Braking non ABS models All models have power 4-wheel disc brakes. They adjust automatically as the brake pads or linings wear down. Apply the brake pedal gradually. Use the “squeeze” technique — push on the brake pedal with a steadily increasing force.
Page 157 Braking with ABS brakes On vehicles equipped with an antilock braking system (ABS), a noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS braking events. Pedal pulsation coupled with noise while braking under panic conditions or on loose gravel, wet or snowy roads is normal and indicates proper functioning of the vehicle’s antilock brake system.
Page 158 Ford Motor Company has not found any detrimental effects of popular mobile radio transmitting equipment installed on vehicles with the anti-lock brake system, if the equipment is installed according to the manufacturer’s...
Page 159 The parking brake WARNING Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission). To release the parking brake, pull the handle upward, push in the button, then lower the handle.
Page 160: Steering Your Vehicle
The parking brake system is designed for static parking only and is not designed to stop a moving vehicle, but you can use the parking brake to stop your vehicle in an emergency if the normal brakes fail. However, since the parking brake applies only the rear brakes, the stopping distance will increase greatly and the handling of your vehicle will be adversely...
Page 161 Never hold the steering wheel to the extreme right or left for more than five seconds if the engine is running. This can damage the power steering pump. Procedures for driving your vehicle will vary depending on which type of transmission your vehicle has.
Page 162 feature is active when the ignition is in the ON position. If the gearshift lever CANNOT be moved from P (Park) with the brake pedal depressed: 1. Turn the engine off and remove the ignition key. 2. Apply parking brake. 3.
Page 163 The positions of the console-mounted gearshift Once the gearshift is secure in the desired position, release the brake pedal and use the accelerator as necessary. R (Reverse) With the gearshift in the R (Reverse) position, the vehicle will move backward. You should always come to a complete stop before shifting into or out of R (Reverse).
Page 164 Driving Your vehicle’s gearshift is console-mounted on the floor. The Transmission Control Switch (TCS) is located on the gearshift handle. The Transmission Control Indicator Light (O/D OFF) is located on the instrument panel. You can put the gearshift lever in any of the several positions.
Page 165 However, Overdrive also shifts into a fourth gear —an overdrive gear — when your vehicle cruises at an appropriate consistent speed for any length of time. This fourth gear will increase your fuel economy when you travel at cruising speeds. When to use D (Overdrive) —...
Page 166: Driving With A Manual Transmission
WARNING Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn off the ignition whenever you leave your vehicle. WARNING Never leave your vehicle unattended while it is running. You can tell a console-mounted gearshift is securely latched in P (Park) if the lever is adjacent to the P (Park) and you cannot move it without pushing in the thumb button.
Page 167 Shifting the Gears The gearshift can be in one of seven possible positions, as shown below. The positions of the floor-mounted gearshift Always push the clutch pedal all the way in when you shift. You should upshift according to the speeds given in the chart in this section. Backing up To shift into R (Reverse): 1.
Page 168 Upshifting Most of the time, you should upshift at the following speeds: Shift Speeds for 3.8L Engine Models Shift Speeds for 4.6L Engine Models * In these gears, you may sometimes shift at lower speeds than those we suggest to improve fuel economy.
Page 169 Downshifting When you slow down or climb a steep hill, always downshift before the engine starts to lose power. Downshifting reduces the chance of stalling and gives your vehicle better acceleration to increase speed again. When you drive down steep hills, downshifting helps you keep a safe speed and helps prevent unnecessary wear on the brakes.
Page 170 You can find your vehicle’s GVWR and GAWR on the Safety Compliance Certification Label on the left front door lock facing or the door latch post pillar. The weight limits of your vehicle’s tires affect the GVWR or GAWR limitations. Usage of replacement tires with higher weight limits than originals does not increase GVWR or GAWR.
Page 171 If you do not know the actual weights of these items, use the following procedure to figure the weight of a load: 1. Weigh your vehicle without the driver, passengers and luggage. You might take your vehicle to a shipping company or an inspection station for trucks.
Page 172: Trailer Towing
Trailer Towing Your vehicle does not come from the factory fully equipped to tow. No towing packages are available through Ford or Lincoln/Mercury dealers. Because towing a trailer puts extra strain on your vehicle, you must follow certain precautions for your safety and the good of your...
Page 173 If you are not certain that you are using the right equipment in the proper manner, see your Ford or Lincoln-Mercury dealer. Do not use hitches that clamp onto your vehicle’s bumper. The bumper is not designed to bear the load.
Page 174 Connecting the safety chains Always attach the trailer’s safety chains to your vehicle. They help protect your trailer if the hitch breaks. To connect the trailer’s safety chains: 1. Cross the chains under the trailer tongue and attach them to your vehicle’s frame or hook retainers.
Page 175 To get the proper equipment for hooking up your trailer’s lights, see your local trailer dealer and your Ford dealer. Be sure to follow their instructions carefully. If you do not install trailer lights correctly, you may cause damage to the vehicle’s lighting...
Page 176 If you use the speed control while you are towing on very long, steep grades, the speed control may shut off. Servicing Your Vehicle If You Tow If you tow a trailer for a long distance, your vehicle will need to be serviced more frequently than usual.
Page 177 WARNING To avoid losing control on slippery roads, do not downshift into Low with the automatic transmission when moving faster than 20 mph (32 km/h). Do not downshift into First with the manual transmission when moving faster than 5 mph (8 km/h). WARNING Do not use the speed control in heavy traffic or on roads that are winding,...
Page 178 High water Do not drive through flooded areas unless you are sure that the water is below the bottom of the wheel rims. If you must drive through high water, drive slowly. You may have limited traction or wet brakes, so allow extra stopping distance because your vehicle will not stop as quickly as usual.
Page 179: Roadside Emergencies
Roadside Emergencies Hazard Flashers The flashers work whether your vehicle is running or not. The flashers work for up to two hours when the battery is fully charged and in good condition without draining the battery excessively. If the flashers run for longer than two hours or if the battery is not fully charged, the battery can be drained.
Page 180 The instrument panel fuse panel location The instrument panel fuse panel...
Page 181 The Instrument Panel Fuses, Circuit Breakers and Relays...
Page 183 These, like fuses, open when the circuit load exceeds their amperage rating. High current fuses may be purchased from your Ford or Lincoln-Mercury dealer. The high current fuse panel is located in the engine compartment on the left-hand fender apron.
Page 184 The high current fuse panel...
Page 185 The high current fuses and relays...
Page 186 Checking and Replacing Fuses If you need to check a fuse, follow these steps: 1. Find the fuse panel cover below and to left of the steering column, in the instrument panel. Pull outward on the handle below the word “fuses” to expose the fuse panel. Squeeze the two backing tabs and pull to remove the cover.
Page 187 WARNING Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. 5. Replace the cover. Circuit Breakers If you need to check a circuit breaker that is on the fuse panel, see Checking and replacing fuses in this chapter to find out how to locate the fuse panel.
Page 188 Since the circuit breaker for the headlamps is mounted in the headlamp switch, you must replace the entire switch to install a new circuit breaker. If the Engine Cranks but Does Not Start or Does Not Start After a Collision Fuel Pump Shut-off Switch If the engine cranks but does not start or does not start after a collision, the fuel pump shut-off...
Page 189: Changing A Tire
WARNING If you see or smell fuel, do not reset the switch or try to start your vehicle. Have all the passengers get out of the vehicle and call the local fire department or a towing service. If your engine cranks but does not start after a collision or substantial jolt: 1.
Page 190 The Temporary Spare Tire You have a high pressure temporary spare tire. This spare tire is smaller than a regular tire and is designed for emergency use only. Use it only when you get a flat tire and replace it as soon as you can.
Page 191 use the wheel for any other type of vehicle. drive through an automatic car wash with this tire. Because the temporary spare tire is smaller than a conventional tire, it reduces the ground clearance. Your vehicle may get caught in the rails and it could be damaged. Spare Tire Location The spare is stored in the trunk.
Page 192 Preparing to Change the Tire 1. Make sure that your vehicle will not move or roll. If you have an automatic transmission, put the gearshift in P (Park). If you have a manual transmission, put the gearshift in 1 (First). Set the parking brake and block the wheel that is diagonally opposite the tire that you are changing.
Page 193 2. Get out the spare tire and jack. 3. The exposed lug nut wheel cover screws onto the lug nuts. It is removed by using the wheel lug nut wrench to turn each lug nut cover counter-clockwise. This will NOT loosen the wheel lug nuts.
Page 194 WARNING To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire.
Page 195 The improper lift point NOTE: Never use the differential housing as a lift point. 2. Turn the jack handle clockwise until the wheel clears the ground. Remove the wheel lug nuts. 3. Replace the flat tire with the spare tire, making sure that the air valve stem is facing outward.
Page 196 6. Remove the jack and fully tighten the lug nuts in the order shown in the following illustration. As soon as possible, have your dealer or a qualified service technician check the lug nuts for proper torque specifications. The lug nuts on the wheel 7.
Page 197 Anti-Theft Wheel Lug Nuts (If equipped) The aluminum wheels on Mustang 4.6L engine vehicles are secured with locking lug nuts. One of the lug nuts on each wheel must be removed and installed with a special key.
Page 198: Jump-Starting Your Vehicle
Removing the anti-theft lug nut Insert the key over the locking lug nut. Make sure that you hold the key square to the lug nut. If you hold the key on an angle, you may damage the key and the lug nut. Place the lug nut wrench over the lug nut key and apply pressure on the key with the wrench.
Page 199 WARNING Applying too much pressure on the ends when lifting a battery could cause acid to spill. Lift the battery with a carrier or with your hands on the opposite corners. WARNING Batteries contain sulfuric acid which burns skin, eyes, and clothing. If the acid touches someone’s skin, eyes, or clothing, immediately flush the area with water for at least 15 minutes.
Page 200 2. Do not disconnect the battery of the disabled vehicle. You could damage the vehicle’s electrical system. 3. Park the booster vehicle close to the hood of the disabled vehicle. Make sure the vehicles do not touch each other. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts.
Page 201 3. Connect one end of the second cable to the negative ( ) terminal of the booster battery — NOT to the discharged battery. 4. Connect the other end of that cable to a good metallic surface on the engine or frame of the disabled vehicle making sure it is clear of any rotating engine components.
Page 202 The 3.8L SFI engine...
Page 203 The 4.6L SFI Engine...
Page 204 Jump-Starting 1. Make sure that the jumper cables are not in the way of moving engine parts, then start the booster vehicle. Run the engine at a moderate speed. 2. Let the discharged battery charge for a few minutes and then start the disabled vehicle. It may take a couple of tries before the vehicle starts.
Page 205: Towing Your Vehicle
Mustang Convertible DO NOT TOW WITH SLINGBELT EQUIPMENT. Ford Motor Company has not developed or approved a T-hook sling-type procedure. Use wheel lift or flatbed equipment. If your vehicle is to be towed from the rear...
Page 206 When calling for a tow truck, tell the operator what kind of vehicle you have. A towing manual is available from Ford Motor Company for all authorized tow truck operators. Have your tow truck driver refer to this manual for the proper hook-up and towing procedures for your vehicle.
Page 207: Maintenance And Care
Maintenance and Care Service Made Easy Ford has two goals for servicing your vehicle. 1. When we can, we design parts that do not need to be serviced. 2. We want to make servicing your vehicle as easy as possible. To help you:...
Page 208 Motorcraft parts are designed and built to provide the best performance in your vehicle. Using these parts for replacement is your assurance that Ford-built quality stays in your vehicle. NOTE: Always dispose of used automotive fluids in a responsible manner. Follow your community’s standards for...
Page 209 Do not work on a vehicle in an enclosed space with the engine running, unless you are sure you have enough ventilation. Never get under a vehicle while it is supported only by a jack. If you must work under a vehicle, use safety stands. Keep all lit cigarettes and other smoking materials away from the battery and all fuel-related parts.
Page 210 Opening the Hood 1. Inside the vehicle, pull the hood release located under the lower left corner of the instrument panel. 2. Go around to the front of the vehicle, and release the auxiliary catch that is located under the front edge of the hood at the center of the vehicle.
Page 211: Engine Compartment
Engine Compartment Your vehicle has one of these types of engines: a 3.8 liter SFI engine a 4.6 liter SFI engine The following pages show diagrams of each engine type and where to find items that you should regularly service.
Page 214 Engine Oil Recommendations We recommend using Motorcraft oil or an equivalent oil meeting Ford Specification WSS-M2C153-F and displaying the American Petroleum Institute CERTIFICATION MARK on the front of the container. The API Certification Mark Never use: “Non-Detergent” oils Oils labeled API SA, SB, SC, SD, SE, SF or SG...
Page 215 Checking and Adding Engine Oil Since the proper amount of engine oil is important for safe engine operation, check the oil using the dipstick each time you put fuel in your vehicle. Remember the engine must be off, the oil must be warm and the vehicle must be parked on level ground.
Page 216 Engine oil dipstick — 3.8 liter engines 6. Carefully, pull the dipstick out again. If the oil level is below the “ADD 1 QT” line (3.8L) or at the “MIN” mark (4.6L), add engine oil as necessary. If the oil level is beyond the letter “F”...
Page 217 (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, startup engine noises or knock may be experienced. It is recommended you use the appropriate “Motorcraft”...
Page 218: Brake Fluid
If the fluid is low, carefully clean and remove the filler cap from the reservoir. Fill the reservoir to the MAX line with Ford High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent fluid meeting Ford...
Page 219 R WARNING If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes. Do not fill the reservoir above the MAX line. The brake fluid reservoir — 3.8L engines The brake fluid reservoir — 4.6L engines If you find that the fluid level is excessively low —...
Page 220 R WARNING Do not let the reservoir for the master cylinder run dry. This may cause the brakes to fail. The Clutch The clutch on your vehicle is operated by a cable that adjusts itself with a little help from you.
Page 221: Windshield Washer Fluid
Windshield Washer Fluid Washer Fluid Check the level of the windshield washer fluid periodically. The reservoir for washer fluid is located on the driver’s side of the engine compartment. Do not operate the washer when the reservoir is empty. The reservoir for the windshield washer fluid R WARNING Do not put windshield washer fluid in the container for the engine coolant.
Page 222: Engine Coolant
as methanol should be used in freezing weather (temperatures below 32˚F [0˚C]). State or local regulations on Volatile Organic Compounds (VOCs) may restrict use of the most common antifreeze, methanol. Washer fluids containing non-methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle’s paint finish, wiper blades, and windshield washer system.
Page 223 The engine coolant recovery reservoir — 3.8L The engine coolant recovery reservoir — 4.6L engines...
Page 224 Checking Hoses Inspect all engine and heater system hoses and hose connections for deterioration, leaks, and loose hose clamps as specified in the Maintenance Schedule booklet. Repair or replace with Motorcraft hoses or equivalent as necessary. Adding Engine Coolant R WARNING Do not put engine coolant in the container for the windshield washer fluid.
Page 225 Ford specification ESE-M97B44-A. Ford Premium Engine Coolant is an optimized formula that will protect all metals and rubber elastomers used in Ford cooling systems for 4 years or 50,000 miles (80,000 km). Do not use alcohol or methanol antifreeze or any engine coolants mixed with alcohol or methanol antifreeze.
Page 226 Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill Capacities in the Capacities and Specifications chapter. Have your dealer check the engine cooling system for leaks if you have to add more than a quart (liter) of engine coolant per month.
Page 227 3.8L engine only Open the vent plug. Remove coolant recovery reservoir cap. Remove radiator pressure cap. With the engine off and cool, add a 50/50 mixture of recommended cooling system fluid and water to the radiator until full, then add to the reservoir until the reservoir is at the FULL-HOT level.
Page 228 Check for leaks at the draincock, block plug and vent plug. Recheck the engine coolant level, using the recommended procedure, after one or two occasions of vehicle use. 4.6L (2V) engine only — GT models With the engine OFF and cool, remove the pressure cap, located on the coolant reservoir.
Page 229: Power Steering Fluid
Reinstall the pressure cap securely. Check for leaks at the draincock. Recheck the engine coolant level, using the recommended procedure, after one or two occasions of vehicle use. Power Steering Fluid Check the level of the power steering fluid at least twice a year (i.e., every Spring and Fall).
Page 230 6. When you are finished, put the dipstick back in and make sure that it fits snugly. The dipstick for power steering fluid Use only power steering fluid that meets Ford Specification Mercon ATF XT-2-QDX or an equivalent. If the power steering fluid is low, do not drive your vehicle for a long period of time before adding fluid.
Page 231 4.6L SFI engine (check cold) NOTE: The brakes on the 4.6L engine vehicles are powered by power steering fluid from the power steering pump. The fluid level in the power steering reservoir will rise and fall due to the amount of charge in the brake booster accumulator.
Page 232: Automatic Transmission Fluid
Fluid level for power steering Use only power steering fluid that meets Ford Specification Mercon ATF XT-2-QDX or an equivalent. NOTE: If the power steering fluid is low, do not drive your vehicle for a long period of time before adding fluid.
Page 233 Checking the Automatic Transmission Fluid It is preferable to check the transmission fluid level at normal operating temperature 150˚F-170˚F (66˚C-77˚C), after approximately 20 miles (30 km) of driving. However, if necessary, you can check the fluid level without having to drive 20 miles (30 km) to obtain a normal operating temperature if outside temperatures are above 50˚F (10˚C).
Page 234 NOTE: If the vehicle has been operated for an extended period at high speeds or in city traffic during hot weather, or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow the fluid to cool before checking. Adding Automatic Transmission Fluid Before adding any fluid, be sure that the correct type will be used.
Page 235: Manual Transmission Fluid
Manual Transmission Fluid The fluid level and quality should not deteriorate under normal driving conditions. However, it is suggested that you have the fluid level checked occasionally. If fluid is required, see Lubricant Specifications in the Index. Battery Your vehicle may have a Motorcraft maintenance-free battery.
Page 236: Wiper Blades
Help Us Protect Our Environment Ford Motor Company strongly recommends that used lead-acid batteries be returned to an authorized recycling facility for disposal. Battery recycling symbol Because your vehicle’s engine is electronically controlled by a computer, some control conditions are maintained by power from the battery.
Page 237 If the blades do not wipe properly, clean both the windshield and the wiper blades. Use undiluted windshield washer solution or a mild detergent. Rinse thoroughly with clear water. Do not use fuel, kerosene, paint thinner, or other solvents to clean your wiper blades. These will damage your blades.
Page 238 R WARNING Improperly inflated tires can affect vehicle handling and can fail suddenly, possibly resulting in loss of vehicle control. Tire Rotation Because your vehicle’s front and rear tires perform different jobs, they often wear differently. To make sure your tires wear evenly and last longer, rotate them as indicated in the following diagram.
Page 239 Replacing the Tires Replace any tires that show wear bands. When your tire shows a wear band, it has only 1/16 inch (2 mm) of tread left. A worn-out tire Because your vehicle’s tires may wear unevenly, you may need to replace them before a wear band appears across the entire tread.
Page 240 Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation — Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear...
Page 241 Traction A B C The traction grades, from highest to lowest, are A, B, and C, and they represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
Page 242 Snow tires must be the same size and grade as the tires you currently have on your vehicle. For your Mustang GT models equipped with 17 in. tires, to achieve the best traction during snow and ice conditions, purchase 245/45ZR17 mud...
Page 243 Use chains on the tires only in an emergency or if the law requires them where you live. If you choose to use chains on your vehicle’s tires, be aware of the following: Make sure the chains are the right size for your tires.
Page 244: Filling The Fuel Tank
Filling the Fuel Tank The fuel door is outside the car on the passenger side near the back. To fill the fuel tank: NOTE: If the fuel tank is filled while the ignition key remains in the “ON” position, there will be a significant delay in fuel indication due to the “anti-slosh”...
Page 245 NOTE: If you replace your fuel cap with an aftermarket fuel filler cap, the customer warranty may be void for any damage to the fuel tank and/or fuel system. Choosing the Right Fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle.
Page 246 Clean air Ford approves the use of gasolines to improve air quality, including reformulated gasolines that contain oxygenates such as a maximum of 10% ethanol or 15% MTBE. There should be no more than 5% methanol with cosolvents and additives to protect the fuel system.
Page 247 Safety Information Relating to Automotive Fuels R WARNING Automotive fuels can cause serious injury or death if misused or mishandled. Turn vehicle off when refueling. Do not smoke when refueling. Fuels are extremely flammable. Do not siphon any fuel by mouth. R WARNING Gasoline or gasoline blended with methanol can cause blindness and...
Page 248: Calculating Fuel Economy
beverage. In sensitive individuals, serious personal injury or sickness could result. Consult a physician promptly if you experience an adverse reaction. Running Out of Fuel NOTE: Avoid running out of fuel because this situation may have an adverse effect on modern powertrain components.
Page 249 Comparisons With EPA Estimates EPA fuel economy figures are obtained from laboratory tests under simulated road conditions and may not reflect the actual conditions you experience or your style of driving. The EPA fuel economy estimate is not a guarantee that you will achieve the fuel economy shown.
Page 250: Emission Control System
Self-Service Pointers If you choose to do your own fueling, you should also perform a few simple maintenance routines. This extra effort will save you additional money and contribute to the driving efficiency of your vehicle. The following procedures require only a tire gauge, a rag, an oil can spout and windshield washer fluid.
Page 251 Ford strongly recommends the use of genuine Ford replacement parts. If other than Ford or Motorcraft parts or Ford authorized remanufactured parts are used for maintenance replacements or for the service of components...
Page 252 R WARNING Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Watch for fluid leaks, strange odors, smoke, loss of oil pressure, the charge warning light, the check engine light, or the temperature warning light.
Page 253 Information about your vehicle’s emission control system is on the Vehicle Emission Control Information decal located on or near the engine. This decal identifies engine displacement and gives some tune-up specifications. How to Prepare Your Vehicle for Inspection/Maintenance (I/M) Testing In some localities it may become a legal requirement to pass an Inspection/Maintenance (I/M) test of the...
Page 254 Lights and Bulb Replacement It is a good idea to check the operation of the following lights frequently: headlamps tail lamps brakelamps hazard flasher high-mount brakelamp turn signals license plate lamps fog lamps (if equipped) The alignment of your headlamps should be checked if: oncoming motorists frequently signal you to turn off your vehicle’s high beams when you...
Page 255 Headlamp Bulb The headlamps on your vehicle use replaceable bulbs. When the lamp burns out, simply replace the bulb, rather than the whole lamp. R WARNING Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass.
Page 256 Removing the headlamp bulb 1. Make sure that the headlamp switch is in the OFF position. 2. Open the hood and locate the headlamp. Headlamp access covers 3. Remove the electrical connector from the bulb by lifting the connector clip upward while pulling the connector rearward.
Page 257 Installing the headlamp bulb 1. With the flat side of the bulb’s plastic base facing upward, insert the glass end of the bulb into the socket. You may need to turn the bulb left or right to line up the grooves in the plastic base with the tabs in the socket.
Page 258 Using the Right Bulbs...
Page 259: Cleaning Your Vehicle
Ford, however, believes that continual improvement in customer satisfaction is a high priority. For this reason, Ford has authorized its dealers to repair, at no charge to the owner, the surfaces of new vehicles damaged by...
Page 260 Cleaning Chrome and Aluminum Parts Wash chrome and aluminum parts with a mild detergent. Do not use steel wool, abrasive cleaners, fuel, or strong detergents. Cleaning Plastic Parts Some of your vehicle’s exterior trim parts are plastic. Clean with a tar and road oil remover if necessary.
Page 261 Cleaning the Instrument Panel Lens Clean the instrument panel lens with a soft cloth and a glass cleaner, such as Ford Ultra-Clear Spray Glass Cleaner, or equivalent. Do not use paper towel or any abrasive cleaner to clean the lens as these may cause scratches.
Page 262 Cleaning the Engine A clean engine is more efficient because a buildup of grease and dirt acts as an insulator, keeping the engine warmer than usual. Extreme care must be used if a power washer is used to clean the engine. The high pressure fluid could penetrate sealed parts and assemblies causing damage or malfunctions.
Page 263: Capacities And Specifications
Capacities and Specifications Refill Capacities, Motorcraft Parts, and Lubricant Specifications Motorcraft Parts If a spark plug is removed for examination, it must be reinstalled in the same cylinder. For 3.8L engines: Cylinders #1, #2, #3 have an EG suffix. Cylinders #4, #5, #6 have an E suffix. For 4.6L (2V) engines: Cylinders #1, #2, #3, #4 have a PG suffix.
Page 264 Fluid Specifications and Capacities NOTE: Rear axle lube quantities must be replaced every 100,000 miles (160,000 km) or if the axle has been submerged in water. Otherwise, the lube should not be checked or changed unless a leak is suspected or repair required.
Page 265 Lubricant Specifications NOTE: Rear axle lube quantities must be replaced every 100,000 miles (160,000 km) or if the axle has been submerged in water. Otherwise, the lube should not be checked or changed unless a leak is suspected or repair required.
Page 266: Vehicle Storage
Vehicle Storage Maintenance Tips If you plan on storing your vehicle for an extended period of time (60 days or more), refer to the following maintenance recommendations to ensure your vehicle stays in good operating condition. General Store all vehicles in a dry, ventilated place. Protect from sunlight, if possible.
Page 267 Cover chrome and stainless steel parts with a thick coat of auto wax to prevent discoloration. Re-wax as necessary when the vehicle is washed. Lubricate all hood, door and trunk lid hinges and latches with a light grade oil. Cover interior soft trim to prevent fading. Keep all rubber parts free from oil and solvents.
Page 268 Ford Gas Stabilizer should be added whenever actual or expected storage periods exceed 60 days. Follow the instructions on the label. The vehicle should then be operated at idle speed to circulate the additive throughout the fuel system. Cooling system Protect against freezing temperatures.
Page 269 Brakes Make sure brakes and parking brake are fully released. Tires Maintain recommended air pressure. Miscellaneous Make sure all linkages, cables, levers and clevis pins under vehicle are covered with grease to prevent rust. Move vehicles at least 25 feet (8 m) every 15 days to lubricate working parts and prevent corrosion.
Page 270: Reporting Safety Defects (U.s. Only)
National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 271: Customer Assistance
Customer Assistance Roadside Assistance Ford Motor Company has set up a 24-hour, seven-day-a-week hotline with trained operators who put you in touch with the help you need if you experience a problem with your vehicle. This complimentary service is provided to you throughout your warranty period of 3 years or 36,000 miles (60,000 km), whichever comes first.
Page 272 1-800-241-FORD (in Canada call 1-800-665-2006). If You Have a Service Problem Ford Motor Company has authorized Ford and Lincoln-Mercury dealerships that can service your vehicle for you. This chapter tells you how to get service or maintenance for your vehicle.
Page 273 If you are away from home when your vehicle needs to be serviced, or if you need more help than the dealer gave you, contact the Ford Customer Assistance Center to find an authorized dealership that may be able to help.
Page 274: The Dispute Settlement Board
Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and...
Page 275 Review? The Board reviews all warranty performance complaints on Ford, Mercury and Lincoln cars and Ford and Mercury light trucks under the new vehicle limited warranty that have not been resolved by either a dealer or Ford Motor Company, except those involving:...
Page 276 DSB’s independent administrator Your dealership and a Ford Motor Company representative are asked to submit statements at this time.
Page 277 Ford Motor Company the names (if known) of all the people you contacted at the dealership a description of the action you expect to...
Page 278 Board’s decision. The decisions of the Board are binding on the dealer and Ford, but not on consumers who may elect to pursue other remedies available to them under state or federal law. Decisions of the...
Page 279 Mediation/Arbitration Program (Canada Only) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Page 280 Use of leaded fuel in your vehicle without a proper conversion may damage the effectiveness of your emissions control system and may cause engine knocking or serious engine damage. Ford Motor Company is not responsible for any damage that is caused by use of improper fuel.
Page 281 If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write to: If you are in other foreign countries, contact the nearest Ford dealership.
Page 282: Accessories
Accessories Ford Accessories for Your Vehicle Ford has many fine products available from your dealer to clean your vehicle and protect its finishes. For best results, use the following, or products of equivalent quality: A wide selection of accessories is available through your local authorized dealer.
Page 283 Safety, Comfort, and Convenience...
Page 284 NOTE: Use only hook and pad design roof racks. Follow all manufacturers recommendations including vehicle speed, rack loads and tie down procedures. Also, DO NOT over torque the hook clamp, as vehicle damage may occur. NOTE: When adding accessories, equipment, passengers, and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front...
Page 285 5 watts or less will not ordinarily affect your vehicle’s operation.) NOTE: Because we have no control over the installation, design, or manufacture of such systems, Ford cannot assume responsibility for any adverse effects or damage that may result if you use this equipment.
Page 287 Label Locations...
Page 298: Index
Index ABS warning light (see Anti-lock brake system) ..12 Accessories ....Accessory position on the ignition ..65 Accessory power source, power point outlet .
Page 299: Audio
Anti-theft system arming the system ... 93 disarming an untriggered system ..94 disarming a triggered system..95 triggering ... . . 92, 94 Appeals (see Dispute settlement board) .
Page 300 Brake fluid ....brake warning light ... 11 checking and adding ..description .
Page 301 Canada, customer assistance ..Canada, warranty information ..Canadian Motor Vehicle Arbitration Plan (CAMVAP) ....Capacities for refilling fluids .
Page 302 Circuit breakers checking and replacing ..see also fuses... . . Cleaning your vehicle ..CD player and discs .
Page 303 Crankcase emission filter ..Customer Assistance Center, Ford (U.S.) . . Customer Assistance Centre, Ford of Canada ..277, 283 Daytime running light system ..59 Defrost rear window .
Page 304 Doors ....79 lubricant specifications ..Driving under special conditions ..bad weather ... . . heavy load .
Page 305 Engine check engine warning light ..17 does not start ... 152, 190 fuel injected engine, starting ..149–150 fuel pump shut-off switch ..preparing to start .
Page 306 Exhaust fumes ... . . Extended Service Plan, Ford ..Fan ....
Page 307 Fuel cap ....removing ....replacing ....Fuel filler door .
Page 308 GAWR (Gross Axle Weight Rating) calculating ....definition ....driving with a heavy load ..location .
Page 309 Heating heater only system ... 57 heating and air conditioning system . . . 55 High beams indicator light ... . . 16 operation .
Page 310 Jack ....operation ... . 194–195 positioning ... . 194–196 storage .
Page 311 Lights, warning and indicator (continued) engine oil pressure ... 22 hazard warning light ..71 high beam ....16 low coolant .
Page 312 Master cylinder, brakes ..Mirrors....77 rearview ....77 side view mirrors .
Page 313 Power point electrical outlet ..63 Power steering dipstick ....driving with power steering ..fluid, checking and adding .
Page 314 Roadside assistance ... Roadside emergencies ..Rotating the tires ... . Safe driving tips .
Page 315 Seat belts (see Safety restraints) ..Seats ....adjusting the seat, manual ..adjusting the seats, power .
Page 316 Speedometer ....20 Starting your vehicle preparing to start your vehicle ..starting a cold engine ..starting after a collision .
Page 317 Tires (continued) tire grades ... . 241–242 treadwear ... . 241–242 wear bands ....Towing a trailer (see Trailer towing) .
Page 318 Upshift speeds ... . . Used engine oil, disposal ..210, 219, 236 Vanity mirror ....79 Variable interval wipers .
Page 319 Warm engine, starting ..Warning chimes key in ignition ... . . 66 safety belt ....13 Warning lights (see Lights) .
Page 320 Windshield, washing ... 69 Windshield washer fluid and wipers ..69 checking and adding fluid ..checking and replacing wiper blades . . liftgate reservoir .
Page 321: Service Station Information
Service Station Information...

This manual is also suitable for:

Mustang gt Mustang 1997 Mustang convertible

Ford Mustang Owner's Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Ford Mustang

Summary of Contents for Ford Mustang

This manual is also suitable for:

Table of Contents